sam9x5 sam-ba

 调试参考 http://www.docin.com/p-872951702.html

AT91SAM9x5 EK Board

 

 

 

 

 

 

 

SoC Features

 

 

The Atmel® | SMART® ARM®-based SAM9x5 family is based on the ARM926EJ-S core. The SAM9x5 family runs at 400 MHz and features connectivity peripherals, high data bandwidth architecture, and a small footprint package option, making it an optimized solution for industrial applications. Peripherals include a soft modem supporting exclusively the Conexant SmartDAA line driver, High Speed (480Mbps) USB Host/Device ports and Full Speed USB Host with on-chip transceivers, 10/100 Ethernet MAC, two HS SDCard/SDIO/MMC interfaces, USARTs, SPIs, I2S, multiple TWIs and 10-bit ADC. It offers support for 8-bank DDR2 and for LPDDR, SDRAM/LPSDRAM, static memories, as well as specific circuitry for MLC/SLC NAND Flash with integrated ECC up to 24 bits. The SAM9x5 family is available in a 217-ball BGA package with 0.8mm ball pitch, as well as a 247-ball BGA package with 0.5mm ball pitch.

AT91SAM9x5 Chip Features


 

 

 

 

Kit Information

 

Kit Overview

 

AT91SAM9x5-EK

 

 

Access the console

 

 

 

 

The usual serial communication parameters are 115200 8-N-1 :

Baud rate 115200
Data 8 bits
Parity None
Stop 1 bit
Flow control None

 

 

 

 

 

Access the console on DBGU serial port

The DBGU serial console can be accessed from the RS-232 connector (marked as DBGU J11).

 

Using RS-232 connector (DBGU J11)

 

  • Connect a DB9 serial cable to the J11 connector
  • Now open your favorite terminal emulator with appropriate settings

 

    • For Linux users: identify the USB connection by monitoring the last lines of dmesg command. The /dev/ttyUSBx or /dev/ttyACMx number will be used to configure the terminal emulator. 
      [605576.562740] usb 1-1.1.2: new full-speed USB device number 17 using ehci-pci
[605576.660920] usb 1-1.1.2: New USB device found, idVendor=0403, idProduct=6001
[605576.660933] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[605576.660939] usb 1-1.1.2: Product: TTL232R-3V3
[605576.660944] usb 1-1.1.2: Manufacturer: FTDI
[605576.660958] usb 1-1.1.2: SerialNumber: FTGNVZ04
[605576.663092] ftdi_sio 1-1.1.2:1.0: FTDI USB Serial Device converter detected
[605576.663120] usb 1-1.1.2: Detected FT232RL
[605576.663122] usb 1-1.1.2: Number of endpoints 2
[605576.663124] usb 1-1.1.2: Endpoint 1 MaxPacketSize 64
[605576.663126] usb 1-1.1.2: Endpoint 2 MaxPacketSize 64
[605576.663128] usb 1-1.1.2: Setting MaxPacketSize 64
[605576.663483] usb 1-1.1.2: FTDI USB Serial Device converter now attached to ttyUSB0
      A /dev/ttyUSB0 node has been created.

 

  • Now open your favorite terminal emulator with appropriate settings

 

 

 

Demo

Demo archives

 

 

 

 

Media typeBoardScreenBinaryDescription
Yocto / Poky based demo
NAND Flash AT91SAM9x5-EK - linux4sam-poky-at91sam9x5ek-5.5.zip (~ 136 MB)
md5: 8f3ba092172b94ae5a3ca671dcc075a6 		Linux4SAM Yocto / Poky based demo
compiled from tag linux4sam_5.5
Follow procedure: #Flash_the_demo
SD Card image AT91SAM9x5-EK - linux4sam-poky-at91sam9x5ek-5.5.img.bz2 (~ 112 MB)
md5: a186147ac73476e2a0314463542b68be 		Linux4SAM Yocto / Poky based demo
compiled from tag linux4sam_5.5
Follow procedure: #Create_a_SD_card_with_the_demo
BuildRoot based demo
SD Card image AT91SAM9x5-EK - linux4sam-buildroot-at91sam9x5ek-5.5.img.bz2 (~ 24 MB)
md5: 4f45b0b0fd7a85011de7837abe0533c1 		Linux4SAM BuildRoot based demo
compiled from tag linux4sam_5.5
Follow procedure: #Create_a_SD_card_with_the_demo

 

 

 

 

 

 

Flash the demo

 

 

 

 

 

 

 

Run script to flash the demo

 

  • Download the demo package for the board.
  • Extract the demo package and launch the script to flash the demo:
    • For Microsoft Windows users: Launch the .bat file corresponding to the board that you are using
      This script will run SAM-BA with proper parameters.
    • For Linux users: if the /dev/ttyACMx that appears is different from /dev/ttyACM0, edit the .sh file and modify /dev/ttyACMx device number
    • For Linux users: Launch the .sh file corresponding to the board that you are using.
      This script will runs SAM-BA with proper parameters
  • When the logfile.log appears (this will take a few minutes), check that 
    ===== Done. =====
    is written at the end of the file.
  • Remove the USB cable.
  • Connect a serial link on DBGU and open the terminal emulator program as explained just above
  • Power cycle the board.
  • Look the system booting on the LCD screen or through the serial line

 

 

 

Play with the demo

 

 

 

Build From source code

 

Setup ARM Cross Compiler

 

 

  • Ubuntu:
    In Ubuntu, you can install the ARM Cross Compiler by doing: 
    sudo apt-get install gcc-arm-linux-gnueabi
export CROSS_COMPILE=arm-linux-gnueabi-

 

  • Others:
    For others, you can download the Linaro cross compiler and setup the environment by doing: 
    wget -c https://releases.linaro.org/14.11/components/toolchain/binaries/arm-linux-gnueabi/gcc-linaro-4.9-2014.11-x86_64_arm-linux-gnueabi.tar.xz
tar xf gcc-linaro-4.9-2014.11-x86_64_arm-linux-gnueabi.tar.xz
export CROSS_COMPILE=`pwd`/gcc-linaro-4.9-2014.11-x86_64_arm-linux-gnueabi/bin/arm-linux-gnueabi-

 

 

 

Build AT91Bootstrap from sources

 

This section describes how to get source code from the git repository, how to configure with the default configuration, how to customize AT91Bootstrap based on the default configuration and finally to build AT91Bootstrap to produce the binary. take the default configuration to download U-Boot from NandFlash for example.

 

Get AT91Boostrap Source Code

You can easily download AT91Bootstrap source code on the at91bootstrap git repository.

To get the source code, you should clone the repository by doing: 

$ git clone git://github.com/linux4sam/at91bootstrap.git
Cloning into 'at91bootstrap'...
remote: Reusing existing pack: 2476, done.
remote: Counting objects: 167, done.
remote: Compressing objects: 100% (167/167), done.
remote: Total 2643 (delta 135), reused 0 (delta 0)
Receiving objects: 100% (2643/2643), 2.06 MiB | 270 KiB/s, done.
Resolving deltas: 100% (1809/1809), done.
$ cd at91bootstrap/

 

Configure AT91Boostrap

 

Assuming you are at the AT91Bootstrap root directory, you will find a board/at91sam9x5ek folder which contains several default configuration files:

 

at91sam9x5eksd_uboot_defconfig
at91sam9x5ekdf_uboot_defconfig
at91sam9x5eknf_uboot_defconfig

TIP Tips: nf means to read nandflash, df means to read serial flash, sd means to read mmc card.
TIP Tips: linux means to load linux kernel to RAM, android means to load android kernel to RAM, uboot means to load u-boot to RAM, dt means to load dtb to RAM.

You can configure AT91Bootstrap to load U-Boot binary from NAND flash by doing: 

$ make mrproper
$ make at91sam9x5eknf_uboot_defconfig
If the configuring process is successful, the .config file can be found at AT91Bootstrap root directory.

 

 

 

Customize AT91Bootstrap

If the default configuration doesn't meet your need, after configuring with the default configuration, you can customize it by doing: 
$ make menuconfig
Now, in the menuconfig dialog, you can easily add or remove some features to/from AT91Bootstrap as the same way as kernel configuration.

 

Build AT91Bootstrap

Then you can build the AT91Bootstrap binary by doing: 
$ make

If the building process is successful, the final .bin image is binaries/at91bootstrap.bin.

 

 

 

Build U-Boot from sources

 

 

Getting U-Boot sources

 

Dedicated page on U-Boot wiki: http://www.denx.de/wiki/U-Boot/SourceCode

You can easily download U-Boot source code from Linux4SAM GitHub U-Boot repository:

 

  • clone the Linux4sam GitHub U-Boot repository 
       $ git clone git://github.com/linux4sam/u-boot-at91.git
   Cloning into 'u-boot-at91'...
   remote: Counting objects: 219350, done.
   remote: Compressing objects: 100% (40142/40142), done.
   remote: Total 219350 (delta 175755), reused 219350 (delta 175755)
   Receiving objects: 100% (219350/219350), 56.01 MiB | 1.24 MiB/s, done.
   Resolving deltas: 100% (175755/175755), done.
   $ cd u-boot-at91

 

  • The source code has been taken from the master branch which is pointing to the latest branch we use. If you want to use the other branch, you can list them and use one of them by doing: 
       $ git branch -r
   origin/HEAD -> origin/master
   origin/master
   origin/u-boot-2012.10-at91
   origin/u-boot-2013.07-at91
   origin/u-boot-2014.07-at91
   origin/u-boot-2015.01-at91
   origin/u-boot-2016.03-at91
   origin/uboot_5series_1.x
   $ git checkout origin/u-boot-2016.03-at91 -b u-boot-2016.03-at91
   Branch u-boot-2016.03-at91 set up to track remote branch u-boot-2016.03-at91 from origin.
   Switched to a new branch 'u-boot-2016.03-at91'

 

 

 

Cross-compiling U-Boot

Before compile the U-Boot, you need setup cross compile toolchain in the section.

 

 

Once the AT91 U-Boot sources available, cross-compile U-Boot is made in two steps : configuration and compiling. Check the Configuration chapter in U-Boot reference manual.

Pointing hand Go to the configs/ to find the exact target when invoking make.

The U-Boot environment variables can be store in different media, above config files can specified where to store the U-Boot environment.

   # To put environment variables in serial flash:
   at91sam9x5ek_spiflash_defconfig
   # To put environment variables in nandflash (default):
   at91sam9x5ek_nandflash_defconfig
   # To put environment variables in SD/MMC card:
   at91sam9x5ek_mmc_defconfig

Here are the building steps for the AT91SAM9x5-EK board:

# You can change the config according to your needs.
make at91sam9x5ek_nandflash_defconfig
make

The result of these operations is a fresh U-Boot binary called u-boot.bin corresponding to the binary ELF file u-boot.

  • u-boot.bin is the file you should store on the board
  • u-boot is the ELF format binary file you may use to debug U-Boot through a JTag link for instance.

 

 

 

 

Build Kernel from sources

 

 

 

Getting Kernel sources

To get the source code, you have to clone the repository:

 

$ git clone git://github.com/linux4sam/linux-at91.git
Cloning into 'linux-sama9x5-github'...
remote: Counting objects: 4524288, done.
remote: Compressing objects: 100% (721/721), done.
remote: Total 4524288 (delta 385), reused 1 (delta 1), pack-reused 4523564
Receiving objects: 100% (4524288/4524288), 1.22 GiB | 1.35 MiB/s, done.
Resolving deltas: 100% (3777338/3777338), done.
Checking connectivity... done.
Checking out files: 100% (49565/49565), done.

The source code has been taken from the master branch which is pointing on the latest branch we use.

Pointing hand Note that you can also add this Linux4SAM repository as a remote GIT repository to your usu

 

$ git remote add linux4sam git://github.com/linux4sam/linux-at91.git
$ git remote update linux4sam
Fetching linux4sam
From git://github.com/linux4sam/linux-at91
 * [new branch]                linux-2.6.39-at91 -> linux4sam/linux-2.6.39-at91
 * [new branch]                linux-3.10-at91 -> linux4sam/linux-3.10-at91
 * [new branch]                linux-3.15-at91 -> linux4sam/linux-3.15-at91
 * [new branch]                linux-3.18-at91 -> linux4sam/linux-3.18-at91
 * [new branch]                linux-3.4.9-at91 -> linux4sam/linux-3.4.9-at91
 * [new branch]                linux-3.6.9-at91 -> linux4sam/linux-3.6.9-at91
 * [new branch]                linux-4.1-at91 -> linux4sam/linux-4.1-at91
 * [new branch]                linux-4.4-at91 -> linux4sam/linux-4.4-at91
 * [new branch]                master     -> linux4sam/master

If you want to use an other branch, you can list them and use one of them by doing this:

 

$ git branch -r
  origin/HEAD -> origin/master
  origin/linux-2.6.39-at91
  origin/linux-3.10-at91
  origin/linux-3.15-at91
  origin/linux-3.18-at91
  origin/linux-3.4.9-at91
  origin/linux-3.6.9-at91
  origin/linux-4.1-at91
  origin/linux-4.4-at91
  origin/master
$ git checkout origin/linux-4.4-at91 -b linux-4.4-at91
Branch linux-4.1-at91 set up to track remote branch linux-4.4-at91 from origin.
Switched to a new branch 'linux-4.4-at91'

 

Configure and Build the Linux kernel

Now you have to configure the Linux kernel according to your hardware. We have two default configuration at91 SoC in arch/arm/configs 
arch/arm/configs/at91_dt_defconfig
arch/arm/configs/sama5_defconfig

 

  • at91_dt_defconfig: for at91sam ARM926 series chips
  • sama5_defconfig: for SAMA5 series chips

 

 

At this step, you can modify default configuration using the menuconfig

$ make ARCH=arm menuconfig

And build the Linux kernel image, before you build you need set up the cross compile toolchain, check this section.

 

$ make ARCH=arm

[..]

  Kernel: arch/arm/boot/Image is ready
  Kernel: arch/arm/boot/zImage is ready

Now you have an usable compressed kernel image zImage.

If you need an uImage you can run this additional step:

 

make ARCH=arm uImage LOADADDR=0x20008000

[..]

  Kernel: arch/arm/boot/zImage is ready
  UIMAGE  arch/arm/boot/uImage
Image Name:   Linux-4.1.0-linux4sam_5.3+
Created:      Fri Sep  9 17:02:45 2016
Image Type:   ARM Linux Kernel Image (uncompressed)
Data Size:    3441072 Bytes = 3360.42 kB = 3.28 MB
Load Address: 20008000
Entry Point:  20008000
  Image arch/arm/boot/uImage is ready

 

make ARCH=arm dtbs

[..]

  DTC     arch/arm/boot/dts/at91rm9200ek.dtb
  DTC     arch/arm/boot/dts/mpa1600.dtb
  DTC     arch/arm/boot/dts/animeo_ip.dtb
  DTC     arch/arm/boot/dts/at91-qil_a9260.dtb
  DTC     arch/arm/boot/dts/aks-cdu.dtb
  DTC     arch/arm/boot/dts/ethernut5.dtb
  DTC     arch/arm/boot/dts/evk-pro3.dtb
  DTC     arch/arm/boot/dts/tny_a9260.dtb
  DTC     arch/arm/boot/dts/usb_a9260.dtb
  DTC     arch/arm/boot/dts/at91sam9261ek.dtb
  DTC     arch/arm/boot/dts/at91sam9263ek.dtb
  DTC     arch/arm/boot/dts/tny_a9263.dtb
  DTC     arch/arm/boot/dts/usb_a9263.dtb
  DTC     arch/arm/boot/dts/at91-foxg20.dtb
  DTC     arch/arm/boot/dts/at91-kizbox.dtb
  DTC     arch/arm/boot/dts/at91sam9g20ek.dtb
  DTC     arch/arm/boot/dts/at91sam9g20ek_2mmc.dtb
  DTC     arch/arm/boot/dts/tny_a9g20.dtb
  DTC     arch/arm/boot/dts/usb_a9g20.dtb
  DTC     arch/arm/boot/dts/usb_a9g20_lpw.dtb
  DTC     arch/arm/boot/dts/at91sam9m10g45ek.dtb
  DTC     arch/arm/boot/dts/pm9g45.dtb
  DTC     arch/arm/boot/dts/at91sam9n12ek.dtb
  DTC     arch/arm/boot/dts/at91sam9rlek.dtb
  DTC     arch/arm/boot/dts/at91-ariag25.dtb
  DTC     arch/arm/boot/dts/at91-ariettag25.dtb
  DTC     arch/arm/boot/dts/at91-cosino_mega2560.dtb
  DTC     arch/arm/boot/dts/at91-kizboxmini.dtb
  DTC     arch/arm/boot/dts/at91sam9g15ek.dtb
  DTC     arch/arm/boot/dts/at91sam9g25ek.dtb
  DTC     arch/arm/boot/dts/at91sam9g35ek.dtb
  DTC     arch/arm/boot/dts/at91sam9x25ek.dtb
  DTC     arch/arm/boot/dts/at91sam9x35ek.dtb

If the building process is successful, the final images can be found under arch/arm/boot/ directory.

 

 

 

 

Build Yocto/Poky rootfs from sources

 

 

Note that building an entire distribution is a long process. It also requires a big amount of free disk space.

The support for Atmel AT91 SoC family is included in a particular Yocto layer: meta-atmel. The source for this layer are hosted on Linux4SAM GitHub account: https://github.com/linux4sam/meta-atmel

 

Building environment

A step-by-step comprehensive installation is explained in the Yocto Project Quick Start. The following lines have to be considered as an add-on that is AT91 specific or that can facilitate your setup.

 

Prerequisite

Here are the reference pages for setting up a Yocto building environment: What You Need and How You Get It.

 

Step by step build procedure

Note here is a copy of the README procedure available directly in the meta-atmel layer. This file in the meta-atmel layer repository must be considered as the reference and the following copy can be out-of-sync.

 

Supported SoCs / MACHINE names
==============================
- SAMA5D2 product family / sama5d2-xplained
- SAMA5D4 product family / sama5d4ek, sama5d4-xplained
- SAMA5D3 product family / sama5d3xek, sama5d3-xplained
- AT91SAM9x5 product family (AT91SAM9G15, AT91SAM9G25, AT91SAM9X25, AT91SAM9G35 and AT91SAM9X35) / at91sam9x5ek
- AT91SAM9RL / at91sam9rlek
- AT91SAM9G45 / at91sam9m10g45ek


Sources
=======
- meta-atmel
URI: git://github.com/linux4sam/meta-atmel.git
URI: https://github.com/linux4sam/meta-atmel.git
Branch: krogoth


Dependencies
============
This Layer depends on :
- meta-openembedded
URI: git://git.openembedded.org/meta-openembedded
URI: http://cgit.openembedded.org/meta-openembedded/
Branch: krogoth

Optionally:
- meta-qt5
URI: git://github.com/meta-qt5/meta-qt5.git
URI: https://github.com/meta-qt5/meta-qt5
Branch: krogoth


Build procedure
===============
0/ Create a directory
mkdir my_dir
cd my_dir

1/ Clone yocto/poky git repository with the proper branch ready
git clone git://git.yoctoproject.org/poky -b krogoth

2/ Clone meta-openembedded git repository with the proper branch ready
git clone git://git.openembedded.org/meta-openembedded -b krogoth

3/ Clone meta-qt5 git repository with the proper branch ready
git clone git://github.com/meta-qt5/meta-qt5.git -b krogoth

4/ Clone meta-atmel layer with the proper branch ready
git clone git://github.com/linux4sam/meta-atmel.git -b krogoth

5/ Enter the poky directory to configure the build system and start the build process
cd poky

6/ Initialize build directory
source oe-init-build-env build-atmel

7/ Add meta-atmel layer to bblayer configuration file
vim conf/bblayers.conf

# POKY_BBLAYERS_CONF_VERSION is increased each time build/conf/bblayers.conf
# changes incompatibly
POKY_BBLAYERS_CONF_VERSION = "2"

BBPATH = "${TOPDIR}"
BBFILES ?= ""

BSPDIR := "${@os.path.abspath(os.path.dirname(d.getVar('FILE', True)) + '/../../..')}"

BBLAYERS ?= " \
  ${BSPDIR}/poky/meta \
  ${BSPDIR}/poky/meta-poky \
  ${BSPDIR}/poky/meta-yocto-bsp \
  ${BSPDIR}/meta-atmel \
  ${BSPDIR}/meta-openembedded/meta-oe \
  ${BSPDIR}/meta-openembedded/meta-networking \
  ${BSPDIR}/meta-openembedded/meta-python \
  ${BSPDIR}/meta-openembedded/meta-ruby \
  ${BSPDIR}/meta-openembedded/meta-multimedia \
  ${BSPDIR}/meta-qt5 \
  "

BBLAYERS_NON_REMOVABLE ?= " \
  ${BSPDIR}/poky/meta \
  ${BSPDIR}/poky/meta-poky \
  "

8/ Edit local.conf to specify the machine, location of source archived, package type (rpm, deb or ipk)
Pick one MACHINE name from the "Supported SoCs / MACHINE names" chapter above
and edit the "local.conf" file. Here is an example:

vim conf/local.conf
[...]
MACHINE ??= "sama5d3-xplained"
[...]
DL_DIR ?= "your_download_directory_path"
[...]
PACKAGE_CLASSES ?= "package_ipk"
[...]
USER_CLASSES ?= "buildstats image-mklibs"

To get better performance, use the "poky-atmel" distribution by also adding that
line:
DISTRO = "poky-atmel"

9/ Build core minimal image
bitbake core-image-minimal

10/ We found that additional local.conf changes are needed for our QT demo
image. You can add these two lines at the end of the file:
vim conf/local.conf
[...]
LICENSE_FLAGS_WHITELIST += "commercial"
SYSVINIT_ENABLED_GETTYS = ""

11/ Build Atmel demo images
bitbake atmel-qt5-demo-image


Typical bitbake output
======================
Build Configuration:
BB_VERSION        = "1.30.0"
BUILD_SYS         = "x86_64-linux"
NATIVELSBSTRING   = "universal"
TARGET_SYS        = "arm-poky-linux-gnueabi"
MACHINE           = "sama5d2-xplained"
DISTRO            = "poky-atmel"
DISTRO_VERSION    = "2.1"
TUNE_FEATURES     = "arm armv7a vfp thumb neon       callconvention-hard       cortexa5"
TARGET_FPU        = "hard"
meta
meta-poky
meta-yocto-bsp    = "krogoth:6c1c01392d91f512e2949ad1d57a75a8077478ba"
meta-atmel        = "krogoth:28c4b5d70f3f7df6f8b108a01f621ca0cf23c1a4"
meta-multimedia
meta-networking
meta-python
meta-ruby
meta-oe           = "krogoth:abd1795729501a13608da67054b9cbf185404be3"
meta-qt5          = "krogoth:4ec27e218d725677279d265ac1fc256443d665f7"

 

 

 

Using SAM-BA to flash components to board

 

 

NAND Flash demo - Memory map

demo_nandflash_map_lnx4sam.png

 

 

Launch SAM-BA tools

 

  • According to this section make sure that the chip can execute the SAM-BA Monitor.

 

 

 

  • Start SAM-BA GUI application.
  • Select the board: "at91sama9x35-ek" in the drop-down menu and choose the USB connection.
samba_board_select_at91sam9x35ek.png

 

  • Click the "Connect" button, the SAM-BA main window show up:
samba_main_window_nand_at91sam9x35ek.png

 

 

 

 

 

Configure NAND ECC

 

Using OS default PMECC parameters

 

 

  1. Choose the NandFlash tab in the SAM-BA GUI interface.
  2. Initialize the NandFlash by choosing the Enable NandFlash action in the Scripts rolling menu, then press Execute button.
  3. Enable the PMECC by choosing the Enable OS PMECC parameters action, then press Execute button.
samba_scripts_menu.png

 

 

Configure PMECC parameters (optional)

 

 

 

 

Programming components into NAND

 

 

Program AT91Bootstrap binary

 

 

  • Choose Send Boot File action, then press Execute button to select the at91bootstrap binary file and to program the binary to the NandFlash.

scripts_menu_send_boot_file.png

 

Program U-Boot binary

 

  1. Modify the Address to 0x40000
  2. Choose Send File Name open file dialog and select the U-Boot binary file and to program the binary to the NandFlash.
  3. Click Send File button to program the binary to the NandFlash in address 0x40000.
samba_send_file_nand.png

 

 

Program Linux dtb file

 

  1. Modify the Address to 0x180000
  2. Choose Send File Name open file dialog and select the dtb binary file and to program the binary to the NandFlash.
  3. Click Send File button to program the binary to the NandFlash in address 0x180000.
samba_send_file_nand.png

 

 

Program Linux Kernel file

 

  1. Modify the Address to 0x200000
  2. Choose Send File Name open file dialog and select the Linux kernel binary file and to program the binary to the NandFlash.
  3. Click Send File button to program the binary to the NandFlash in address 0x200000.
samba_send_file_nand.png

 

 

Program rootfs UBI file

Make sure you erased the nand area (0x800000~END of nand) before you program it.

 

  1. Modify the Address to 0x800000
  2. Choose Send File Name open file dialog and select the UBI filesystem binary file and to program the binary to the NandFlash.
  3. Click Send File button to program the binary to the NandFlash in address 0x800000.
samba_send_file_nand.png

 

 

 

 

 

 

Recent FAQ

 

 

AT91sam9x5-ek boards

• Shutdown Wake Up: Use the Wakeup Feature of the Shutdown Controller.. (Kernel, linux-4.4-at91)
• Real Time: Enable Real Time support for AT91SAM9 Soc. (Kernel)
• Yocto Project FAQ: Some Yocto Project FAQ entries. (YoctoProject)

posted on 2016-11-02 09:13  嵌入式操作系统  阅读(1298)  评论(0)  编辑  收藏  举报

导航