本文主要记录I.MX6 U-boot是如何配置PWM，发现文中的pwm0对应的引脚和真正的电路板的pwm0不是一个，也就意味着其实是引脚连接错了，另外之前一直有一个疑问：为什么双屏显示的时候，有一个屏在U-boot阶段和Kernel阶段总是不亮。原因应该是这里只初始化了一个显示控制部分，也就是不会初始两个PWM。
/*******************************************************************************
* I.MX6 U-boot PWM hacking
* 说明：
* 本文主要记录I.MX6 U-boot是如何配置PWM，发现文中的pwm0对应的引脚和真正的
* 电路板的pwm0不是一个，也就意味着其实是引脚连接错了，另外之前一直有一个
* 疑问：为什么双屏显示的时候，有一个屏在U-boot阶段和Kernel阶段总是不亮。原因
* 应该是这里只初始化了一个显示控制部分，也就是不会初始两个PWM。
*
* 2016-3-7 深圳 南山平山村 曾剑锋
******************************************************************************/
cat bootable/bootloader/uboot-imx/board/freescale/mx6q_sabresd/mx6q_sabresd.c
......
#ifdef CONFIG_LCD
void lcd_enable(void)
{
......
imx_pwm_config(pwm0, 25000, 50000); ------------+
imx_pwm_enable(pwm0); ------------*-+
| |
#if defined CONFIG_MX6Q | |
/* PWM backlight */ | |
mxc_iomux_v3_setup_pad(MX6Q_PAD_SD1_DAT3__PWM1_PWMO); | |
/* LVDS panel CABC_EN0 */ | |
mxc_iomux_v3_setup_pad(MX6Q_PAD_NANDF_CS2__GPIO_6_15); | |
/* LVDS panel CABC_EN1 */ | |
mxc_iomux_v3_setup_pad(MX6Q_PAD_NANDF_CS3__GPIO_6_16); | |
#elif defined CONFIG_MX6DL | |
/* PWM backlight */ | |
mxc_iomux_v3_setup_pad(MX6DL_PAD_SD1_DAT3__PWM1_PWMO); | |
/* LVDS panel CABC_EN0 */ | |
mxc_iomux_v3_setup_pad(MX6DL_PAD_NANDF_CS2__GPIO_6_15); | |
/* LVDS panel CABC_EN1 */ | |
mxc_iomux_v3_setup_pad(MX6DL_PAD_NANDF_CS3__GPIO_6_16); | |
#endif | |
...... | |
} | |
...... | |
| |
static struct pwm_device pwm0 = { <-----------+ |
.pwm_id = 0, | |
.pwmo_invert = 0, | |
}; | |
| |
| |
int imx_pwm_config(struct pwm_device pwm, int duty_ns, int period_ns) <----+ |
{ |
unsigned long long c; |
unsigned long period_cycles, duty_cycles, prescale; |
u32 cr; |
|
if (period_ns == 0 || duty_ns > period_ns) |
return -1; |
|
pwm.mmio_base = pwm.pwm_id ? (unsigned long)IMX_PWM2_BASE: |
(unsigned long)IMX_PWM1_BASE; |
|
if (pwm.pwmo_invert) |
duty_ns = period_ns - duty_ns; |
|
c = mxc_get_clock(MXC_IPG_PERCLK); |
c = c * period_ns; |
do_div(c, 1000000000); |
period_cycles = c; |
|
prescale = period_cycles / 0x10000 + 1; |
|
period_cycles /= prescale; |
c = (unsigned long long)period_cycles * duty_ns; |
do_div(c, period_ns); |
duty_cycles = c; |
|
writel(duty_cycles, pwm.mmio_base + MX_PWMSAR); |
writel(period_cycles, pwm.mmio_base + MX_PWMPR); |
|
cr = MX_PWMCR_PRESCALER(prescale) | |
MX_PWMCR_STOPEN | MX_PWMCR_DOZEEN | |
MX_PWMCR_WAITEN | MX_PWMCR_DBGEN; |
|
cr |= MX_PWMCR_CLKSRC_IPG_HIGH; |
|
writel(cr, pwm.mmio_base + MX_PWMCR); |
|
return 0; |
} |
|
int imx_pwm_enable(struct pwm_device pwm) <----------------+
{
unsigned long reg;
int rc = 0;
if (pwm.enable_pwm_clk)
pwm.enable_pwm_clk();
pwm.mmio_base = pwm.pwm_id ? (unsigned long)IMX_PWM2_BASE:
(unsigned long)IMX_PWM1_BASE;
reg = readl(pwm.mmio_base + MX_PWMCR);
reg |= MX_PWMCR_EN;
writel(reg, pwm.mmio_base + MX_PWMCR);
if (pwm.enable_pwm_pad)
pwm.enable_pwm_pad();
return rc;
}
