TD-LTE华为 DBS3900数据配置实践 典型案例

案例：华为 DBS3900 双基站二扇区配置（同频切换）

一、数据配置前的硬件准备：

HW-DBS3900: （1#基站名称）

FAN （风扇），安装在 16#槽位；

LBBP （基带处理单板），安装在2#槽位 ;

LBBP （基带处理单板 ，安装在3#槽位 ;

UPEU （环境监控和电源单板），安装在19# 槽位 ;

LMPT （主控单板），安装在7#槽位 ;

 

 

ENodeB-WX2: （2#基站名称）

FAN （风扇），安装在 16#槽位；

LBBP （基带处理单板） ，安装在 2#槽位 ;

LBBP （基带处理单板） ，安装在 3#槽位 ;

UPEU （环境监控和电源单板） ，安装在 19# 槽位 ;

LMPT （主控单板），安装在7#槽位。

二、流程图：

 

 

三、规划与协商数据准备：

 

 

四、 配置全局设备参数：

HW-DBS3900:（1#基站名称）
MOD ENODEB: ENODEBID=0, NAME="HW-DBS3900", ENBTYPE=DBS3900_LTE, GCDF=DEG, LONGITUDE=100, LATITUDE=100, LOCATION="wx", PROTOCOL=CPRI;
ADD CNOPERATOR: CnOperatorId=0, CnOperatorName="CMCC", CnOperatorType=CNOPERATOR_PRIMARY, Mcc="460", Mnc="00";
ADD CNOPERATORTA: TrackingAreaId=0, CnOperatorId=0, Tac=0;
ADD CABINET: CN=0, TYPE=VIRTUAL;
ADD SUBRACK: CN=0, SRN=0, TYPE=BBU3900;
ADD BRD: CN=0, SRN=0, SN=16, BT=FAN;
ADD BRD: CN=0, SRN=0, SN=2, BT=LBBP, WM=TDD;
ADD BRD: CN=0, SRN=0, SN=3, BT=LBBP, WM=TDD;
ADD BRD: CN=0, SRN=0, SN=19, BT=UPEU;
ADD BRD: CN=0, SRN=0, SN=7, BT=LMPT;
ADD RRUCHAIN: RCN=0, TT=CHAIN, HCN=0, HSRN=0, HSN=2, HPN=0;
ADD RRUCHAIN: RCN=1, TT=CHAIN, HCN=0, HSRN=0, HSN=3, HPN=0;
ADD RRU: CN=0, SRN=60, SN=0, RCN=0, PS=0, RT=LRRU, RS=TDL, RXNUM=2, TXNUM=2;
ADD RRU: CN=0, SRN=61, SN=0, RCN=1, PS=0, RT=LRRU, RS=TDL, RXNUM=2, TXNUM=2;

ENodeB-WX2: （2#基站名称）
MOD ENODEB: ENODEBID=1, NAME="WX", ENBTYPE=DBS3900_LTE, GCDF=DEG, LONGITUDE=111, LATITUDE=111, LOCATION="h", PROTOCOL=CPRI;
ADD CNOPERATOR: CnOperatorId=0, CnOperatorName="CMCC", CnOperatorType=CNOPERATOR_PRIMARY, Mcc="460", Mnc="00"; ADD CNOPERATORTA: TrackingAreaId=0, CnOperatorId=0, Tac=0;
ADD CABINET: CN=1, TYPE=VIRTUAL, DESC="h";
ADD SUBRACK: CN=1, SRN=0, TYPE=BBU3900, DESC="h";
ADD BRD: CN=1, SRN=0, SN=16, BT=FAN;
ADD BRD: CN=1, SRN=0, SN=2, BT=LBBP, WM=TDD;
ADD BRD: CN=1, SRN=0, SN=3, BT=LBBP, WM=TDD;
ADD BRD: CN=1, SRN=0, SN=19, BT=UPEU;
ADD BRD: CN=1, SRN=0, SN=7, BT=LMPT;
ADD RRUCHAIN: RCN=0, TT=CHAIN, HCN=1, HSN=2, HPN=0;
ADD RRUCHAIN: RCN=1, TT=CHAIN, HCN=1, HSN=3, HPN=0;
ADD RRU: CN=1, SRN=60, SN=0, RCN=0, PS=0, RT=LRRU, RS=TDL, RXNUM=2, TXNUM=2;
ADD RRU: CN=1, SRN=61, SN=0, RCN=1, PS=0, RT=LRRU, RS=TDL, RXNUM=2, TXNUM=2;

五、配置单站传输数据:

HW-DBS3900:（1#基站名称）
ADD ETHPORT: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, PN=0, PA=COPPER, SPEED=100M, DUPLEX=FULL;
ADD DEVIP: CN=0, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, IP="11.64.16.2", MASK="255.255.0.0";
ADD SCTPLNK: SCTPNO=0, CN=0, SRN=0, SN=7, LOCIP="11.64.16.2", LOCPORT=16705, PEERIP="11.64.15.2", PEERPORT=16448, AUTOSWITCH=ENABLE;
ADD S1INTERFACE: S1InterfaceId=0, S1SctpLinkId=0, CnOperatorId=0;
ADD IPPATH: PATHID=0, CN=0, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, JNRSCGRP=DISABLE, LOCALIP="11.64.16.2", PEERIP="10.148.43.48", ANI=0, APPTYPE=S1, PATHTYPE=ANY;

ADD DEVIP: CN=0, SRN=0,SN=7, SBT=BASE_BOARD, PT=ETH, PN=1, IP="21.11.11.2", MASK="255.255.255.0";
ADD SCTPLNK: SCTPNO=16, CN=0, SRN=0,SN=6, LOCIP="21.11.11.2", LOCPORT=1234, PEERIP="21.11.11.3", PEERPORT=4321, AUTOSWITCH=ENABLE;
ADD X2INTERFACE: X2InterfaceId=16, X2SctpLinkId=16, CnOperatorId=0;
ADD IPPATH: PATHID=16, CN=0, SRN=0, SN=6, SBT=BASE_BOARD, PT=ETH, PN=1, JNRSCGRP=DISABLE, LOCALIP="21.11.11.2", PEERIP="21.11.11.3", ANI=0, APPTYPE=X2, PATHTYPE=ANY;

ENodeB-WX2: （2#基站名称）
ADD ETHPORT: CN=1, SRN=0, SN=7, SBT=BASE_BOARD, PN=0, PA=COPPER, SPEED=100M, DUPLEX=FULL;
ADD DEVIP: CN=1, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, IP="11.66.16.2", MASK="255.255.0.0";
ADD SCTPLNK: SCTPNO=0, CN=1, SRN=0, SN=7, LOCIP="11.66.16.2", LOCPORT=16705, PEERIP="11.66.15.2", PEERPORT=16448, AUTOSWITCH=ENABLE;
ADD S1INTERFACE: S1InterfaceId=0, S1SctpLinkId=0, CnOperatorId=0;
ADD IPPATH: PATHID=0, CN=1, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=0, JNRSCGRP=DISABLE, LOCALIP="11.66.16.2", PEERIP="10.148.43.48", ANI=0, APPTYPE=S1, PATHTYPE=ANY

ADD DEVIP: CN=1, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=1, IP="21.11.11.3", MASK="255.255.255.0";
ADD SCTPLNK: SCTPNO=17, CN=1, SRN=0, SN=7, LOCIP="21.11.11.3", LOCPORT=4321, PEERIP="21.11.11.2", PEERPORT=1234, AUTOSWITCH=ENABLE;
ADD X2INTERFACE: X2InterfaceId=17, X2SctpLinkId=17, CnOperatorId=0;
ADD IPPATH: PATHID=17, CN=1, SRN=0, SN=7, SBT=BASE_BOARD, PT=ETH, PN=1, JNRSCGRP=DISABLE, LOCALIP="21.11.11.3", PEERIP="21.11.11.2", ANI=0, APPTYPE=X2, PATHTYPE=ANY;

六、配置无线层数据：

HW-DBS3900:（1#基站名称）
ADD SECTOR: SECN=0, GCDF=DEG, LONGITUDE=100, LATITUDE=100, SECM=NormalMIMO, ANTM=2T2R, COMBM=COMBTYPE_SINGLE_RRU, CN1=0, SRN1=60, SN1=0, PN1=R0A, CN2=0, SRN2=60,SN2=0,PN2=R0B, ALTITUDE=30;
ADD SECTOR: SECN=1, GCDF=DEG, LONGITUDE=100, LATITUDE=100, SECM=NormalMIMO, ANTM=2T2R, COMBM=COMBTYPE_SINGLE_RRU, CN1=0, SRN1=61, SN1=0, PN1=R0A, CN2=0, SRN2=61,SN2=0,PN2=R0B, ALTITUDE=30;
ADD CELL: LocalCellId=0, CellName="NO.1", SectorId=0, FreqBand=40, UlEarfcnCfgInd=NOT_CFG, DlEarfcn=38749, UlBandWidth=CELL_BW_N100,DlBandWidth=CELL_BW_N100,CellId=0,PhyCellId=0, FddTddInd=CELL_TDD, SubframeAssignment=SA1, SpecialSubframePatterns=SSP7, RootSequenceIdx=0,CellRadius=3000, CustomizedBandWidthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG, UePowerMaxCfgInd=NOT_CFG, MultiRruCellFlag=BOOLEAN_FALSE;
ADD CELL: LocalCellId=1, CellName="NO.2", SectorId=1, FreqBand=40, UlEarfcnCfgInd=NOT_CFG, DlEarfcn=38749, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100,CellId=1,PhyCellId=1, FddTddInd=CELL_TDD, SubframeAssignment=SA1, SpecialSubframePatterns=SSP7, RootSequenceIdx=1, CellRadius=3000, CustomizedBandWidthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG, UePowerMaxCfgInd=NOT_CFG, MultiRruCellFlag=BOOLEAN_FALSE;
ADD CELLOP: LocalCellId=0, TrackingAreaId=0;
ADD CELLOP: LocalCellId=1, TrackingAreaId=0;

ENodeB-WX2: （2#基站名称
ADD SECTOR: SECN=0, GCDF=DEG, LONGITUDE=111, LATITUDE=111, SECM=NormalMIMO, ANTM=2T2R, COMBM=COMBTYPE_SINGLE_RRU, CN1=0, SRN1=60, SN1=0, PN1=R0A, CN2=0, SRN2=60, SN2=0, PN2=R0B, ALTITUDE=30;
ADD SECTOR: SECN=1, GCDF=DEG, LONGITUDE=111, LATITUDE=111, SECM=NormalMIMO, ANTM=2T2R, COMBM=COMBTYPE_SINGLE_RRU, CN1=0, SRN1=61, SN1=0, PN1=R0A, CN2=0, SRN2=61,SN2=0,PN2=R0B, ALTITUDE=30;
ADD CELL: LocalCellId=0, CellName="WX1", SectorId=0, FreqBand=40, UlEarfcnCfgInd=NOT_CFG, DlEarfcn=38749, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100, CellId=10, PhyCellId=10, FddTddInd=CELL_TDD, SubframeAssignment=SA1, SpecialSubframePatterns=SSP7, RootSequenceIdx=0, CellRadius=3000, CustomizedBandWidthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG, UePowerMaxCfgInd=NOT_CFG, MultiRruCellFlag=BOOLEAN_FALSE;
ADD CELL: LocalCellId=1, CellName="WX2", SectorId=1, FreqBand=40, UlEarfcnCfgInd=NOT_CFG, DlEarfcn=38749, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100, CellId=11, PhyCellId=11, FddTddInd=CELL_TDD, SubframeAssignment=SA1, SpecialSubframePatterns=SSP7, RootSequenceIdx=1, CellRadius=3000, CustomizedBandWidthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG, UePowerMaxCfgInd=NOT_CFG, MultiRruCellFlag=BOOLEAN_FALSE;
ADD CELLOP: LocalCellId=0, TrackingAreaId=0;
ADD CELLOP: LocalCellId=1, TrackingAreaId=0;

 

七、激活小区：

HW-DBS3900:（1#基站名称）
ACT CELL: LocalCellId=0;
ACT CELL: LocalCellId=1;
WX: （2#基站名称）
ACT CELL: LocalCellId=0;
ACT CELL: LocalCellId=1;

八、配置相邻小区：

 

HW-DBS3900:（1#基站名称）
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="00", eNodeBId=1, CellId=10, DlEarfcn=38749, UlEarfcnCfgInd=NOT_CFG, PhyCellId=10, Tac=0, CellName="WX1";
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="00", eNodeBId=1, CellId=11, DlEarfcn=38749, UlEarfcnCfgInd=NOT_CFG, PhyCellId=11, Tac=0, CellName="WX2";
ADD EUTRANINTRAFREQNCELL: LocalCellId=0, Mcc="460", Mnc="00", eNodeBId=1, CellId=10, LocalCellName=" HW-DBS39001", NeighbourCellName="WX1";
ADD EUTRANINTRAFREQNCELL: LocalCellId=0, Mcc="460", Mnc="00", eNodeBId=1, CellId=11, LocalCellName=" HW-DBS39001", NeighbourCellName="WX2";
ADD EUTRANINTRAFREQNCELL: LocalCellId=1, Mcc="460", Mnc="00", eNodeBId=1, CellId=10, LocalCellName=" HW-DBS39002", NeighbourCellName="WX1";
ADD EUTRANINTRAFREQNCELL: LocalCellId=1, Mcc="460", Mnc="00", eNodeBId=1, CellId=11, LocalCellName=" HW-DBS39002", NeighbourCellName="WX2";

WX: （2#基站名称）
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="00", eNodeBId=0, CellId=0, DlEarfcn=38749, UlEarfcnCfgInd=NOT_CFG, PhyCellId=0, Tac=0, CellName=" HW-DBS39001";
ADD EUTRANEXTERNALCELL: Mcc="460", Mnc="00", eNodeBId=0, CellId=1, DlEarfcn=38749, UlEarfcnCfgInd=NOT_CFG, PhyCellId=1, Tac=0, CellName=" HW-DBS39002";
ADD EUTRANINTRAFREQNCELL: LocalCellId=0, Mcc="460", Mnc="00", eNodeBId=0, CellId=0, LocalCellName="WX1", NeighbourCellName=" HW-DBS39001";
ADD EUTRANINTRAFREQNCELL: LocalCellId=0, Mcc="460", Mnc="00", eNodeBId=0, CellId=1, LocalCellName="WX1", NeighbourCellName=" HW-DBS39002";
ADD EUTRANINTRAFREQNCELL: LocalCellId=1, Mcc="460", Mnc="00", eNodeBId=0, CellId=1, LocalCellName="WX2", NeighbourCellName=" HW-DBS39002";
ADD EUTRANINTRAFREQNCELL: LocalCellId=1, Mcc="460", Mnc="00", eNodeBId=0, CellId=0, LocalCellName="WX2", NeighbourCellName=" HW-DBS39001";

 

 九、总结

 

 

以上为针对于华为 DBS3900数据配置流程的归纳总结，其实无论什么情况下的数据配置，基本配置流程都是一 样的。当然要是配置数量特别大的基站，那么就要采用 CME 批量数据配置软件借助 M2000 去实现了。

 

加油！