Vim insert mode All In One

Vim insert mode All In One

VIm 插入模式

vim insert mode

i

# i 插入
$ sudo vim /boot/config.txt

o === i + \n

# o 插入, 等价于 i 插入 + 换行
$ sudo vim /boot/config.txt

https://youtu.be/0affY6rdqbM?t=149

demos

pi@rpi3b:~ $ sudo vim /boot/config.txt
pi@rpi3b:~ $ cat /boot/config.txt

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
## 打开✅
hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
## 开启 HDMI ✅
hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
## 开启HDMI ✅
config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
# fix BCM bug ❓
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

# Automatically load overlays for detected cameras
camera_auto_detect=1

# Automatically load overlays for detected DSI displays
display_auto_detect=1

# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2

# Run in 64-bit mode
arm_64bit=1

# Disable compensation for displays with overscan
disable_overscan=1

[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1

[all]

[pi4]
# Run as fast as firmware / board allows
arm_boost=1

[all]

# mini URAT 暂时注释掉 https://www.cnblogs.com/xgqfrms/p/17365120.html#5173367
# dtoverlay=pi3-miniuart-bt
# force_turbo=1

program_usb_boot_mode=1
gpu_mem=100

# o 等价于 i + 换行
# https://youtu.be/0affY6rdqbM?t=149

(🐞 反爬虫测试！打击盗版⚠️）如果你看到这个信息, 说明这是一篇剽窃的文章，请访问 https://www.cnblogs.com/xgqfrms/ 查看原创文章！

Termius

Termius - SSH platform for Mobile and Desktop

https://termius.com/

~/.ssh/known_hosts

https://apps.apple.com/us/app/termius-ssh-sftp-client/id1176074088?mt=12

iPad as an SSH Terminal of Raspberry Pi

https://www.cnblogs.com/xgqfrms/p/17456722.html#5182625
https://www.cnblogs.com/xgqfrms/p/17456722.html#5182626

https://www.cnblogs.com/xgqfrms/p/17456799.html#5183286

refs

---

---

©xgqfrms 2012-2021

www.cnblogs.com/xgqfrms 发布文章使用：只允许注册用户才可以访问！

原创文章，版权所有©️xgqfrms, 禁止转载 🈲️，侵权必究⚠️！

---