STM32 TIM 多通道互补PWM波形输出配置快速入门
platform：stm32f10xxx
lib：STM32F10x_StdPeriph_Lib_V3.5.0
前言
在做三相逆变的时候，需要软件生成SVPWM波形，具体的算法需要产生三对互补的PWM，这样可以驱动六个开关元件，stm32f103中的TIM1高级定时器支持产生三路互补PWM波形，下面进一步学习。
PWM产生的原理
TIM1的OC模块，可以产生PWM波形，具体步骤；
- 寄存器
TIMx CNT每过一个时钟周期就会加1； - 然后
TIMx CNT的值与TIMx CCER进行比较； - 最终改变
OC上的有效电平；
以上只需要配置好TIM1的寄存器即可，无需再编程干预，当然可以动态修改TIMx CCER的值，从而改变占空比。可以参考下图；
PWM模式
这里主要对PWM模式进行配置的时候做一下区分，存在以下两种情况；
TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM2;
那么TIM_OCMode_PWM1和TIM_OCMode_PWM2有什么区别呢？
- TIM_OCMode_PWM1 PWM模式1
在向上计数时，一旦TIMx_CNT<TIMx_CCR1时通道1为有效电平，否则为无效电平
在向下计数时，一旦TIMx_CNT>TIMx_CCR1时通道1为无效电平(OC1REF=0)，否则为有效 电平(OC1REF=1)。 - TIM_OCMode_PWM2 PWM模式2
在向上计数时，一旦TIMx_CNT<TIMx_CCR1时通道1为无效电平，否则为有效电平
在向下计数时，一旦TIMx_CNT>TIMx_CCR1时通道1为有效电平，否则为无效电平。
死区插入和刹车功能
互补PWM还支持插入死区时间，最主要的寄存器是TIMx_BDTR，在标准库中把相关的变量封装到TIM_BDTRInitTypeDef结构体中；具体如下；
typedef struct
{
uint16_t TIM_OSSRState; /*!< Specifies the Off-State selection used in Run mode.
This parameter can be a value of @ref OSSR_Off_State_Selection_for_Run_mode_state */
uint16_t TIM_OSSIState; /*!< Specifies the Off-State used in Idle state.
This parameter can be a value of @ref OSSI_Off_State_Selection_for_Idle_mode_state */
uint16_t TIM_LOCKLevel; /*!< Specifies the LOCK level parameters.
This parameter can be a value of @ref Lock_level */
uint16_t TIM_DeadTime; /*!< Specifies the delay time between the switching-off and the
switching-on of the outputs.
This parameter can be a number between 0x00 and 0xFF */
uint16_t TIM_Break; /*!< Specifies whether the TIM Break input is enabled or not.
This parameter can be a value of @ref Break_Input_enable_disable */
uint16_t TIM_BreakPolarity; /*!< Specifies the TIM Break Input pin polarity.
This parameter can be a value of @ref Break_Polarity */
uint16_t TIM_AutomaticOutput; /*!< Specifies whether the TIM Automatic Output feature is enabled or not.
This parameter can be a value of @ref TIM_AOE_Bit_Set_Reset */
} TIM_BDTRInitTypeDef;
相关的含义看注释可以知道大概意思；这里整理了几个比较重要的变量；
- 死区时间
TIM_DeadTime的计算；TIMx_BDTR的低八位的配置决定了死区的时间；
UTG[7:0]: 死区发生器设置 (Dead-time generator setup)
这些位定义了插入互补输出之间的死区持续时间。假设DT表示其持续时间：
| DTG[7:5]=0xx => DT=DTG[7:0] × Tdtg | Tdtg = TDTS； |
| DTG[7:5]=10x => DT=(64+DTG[5:0]) × Tdtg | Tdtg = 2 × TDTS； |
| DTG[7:5]=110 => DT=(32+DTG[4:0]) × Tdtg | Tdtg = 8 × TDTS； |
| DTG[7:5]=111 => DT=(32+DTG[4:0])× Tdtg | Tdtg = 16 × TDTS； |
例：若TDTS = 125ns(8MHZ)，可能的死区时间为：
0到15875ns，若步长时间为125ns；
16us到31750ns，若步长时间为250ns；
32us到63us，若步长时间为1us；
64us到126us，若步长时间为2us；
注：一旦LOCK级别(TIMx_BDTR寄存器中的LOCK位)设为1、 2或3，则不能修改这些位。
TIM_Break则表示是否决定使用刹车，如果发生错误，则可以通过刹车，第一时间停止PWM波形的产生，从而保证了系统的安全性；
代码实现
#include "stm32f10x.h"
#include "svpwm_driver.h"
#include "stm32f10x_tim.h"
#include "stm32f10x_it.h"
#include <stdio.h>
#define SVPWM_USE_BDT 1
#define USE_HARD_PWM 1
/**
* @brief Configures the different system clocks.
* @param None
* @retval None
*/
void pwm_rcc_init(void)
{
/* TIM1, GPIOA, GPIOB, GPIOE and AFIO clocks enable */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1 | RCC_APB2Periph_GPIOA |
RCC_APB2Periph_AFIO |
RCC_APB2Periph_GPIOB, ENABLE);
}
void pwm_cnt_irq_init(void)
{
}
/**
* @brief Configure the TIM1 Pins.
* @param None
* @retval None
* @note
* PA8 /T1_CH1 ---> HIn3
* PA9 /T1_CH2 ---> HIn2
* PA10/T1_CH3 ---> HIn1
* Out2 ---> PA0/ADC0
* Out3 ---> PA1/ADC1
* PB15/T1_CHN3 ---> LIn1
* PB14/T1_CHN2 ---> LIn2
* PB13/T1_CHN1 ---> LIn3
*/
void pwm_pin_init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
/* GPIOA Configuration: Channel 1, 2 and 3 as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8 | GPIO_Pin_9 | GPIO_Pin_10 ;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* GPIOB Configuration: Channel 1N, 2N and 3N as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13 | GPIO_Pin_14 | GPIO_Pin_15;
GPIO_Init(GPIOB, &GPIO_InitStructure);
}
void pwm_tim_init(void){
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
TIM_OCInitTypeDef TIM_OCInitStructure;
TIM_BDTRInitTypeDef TIM_BDTRInitStructure;
// NVIC_InitTypeDef NVIC_InitStructure;
uint16_t TimerPeriod = 0;
uint16_t Channel1Pulse = 0, Channel2Pulse = 0, Channel3Pulse = 0;
/* TIM1 Configuration ---------------------------------------------------
Generate 7 PWM signals with 4 different duty cycles:
TIM1CLK = SystemCoreClock, Prescaler = 0, TIM1 counter clock = SystemCoreClock
SystemCoreClock is set to 72 MHz for Low-density, Medium-density, High-density
and Connectivity line devices and to 24 MHz for Low-Density Value line and
Medium-Density Value line devices
The objective is to generate 7 PWM signal at 17.57 KHz:
- TIM1_Period = (SystemCoreClock / 17570) - 1
The channel 1 and channel 1N duty cycle is set to 50%
The channel 2 and channel 2N duty cycle is set to 50%
The channel 3 and channel 3N duty cycle is set to 50%
The Timer pulse is calculated as follows:
- ChannelxPulse = DutyCycle * (TIM1_Period - 1) / 100
----------------------------------------------------------------------- */
TimerPeriod = (SYS_FRQ / PWM_FRQ ) - 1;
/* Compute CCR1 value to generate a duty cycle at 50% for channel 1 and 1N */
Channel1Pulse = (uint16_t) (((uint32_t) PWM_DUTY * (TimerPeriod - 1)) / 100);
/* Compute CCR2 value to generate a duty cycle at 37.5% for channel 2 and 2N */
Channel2Pulse = (uint16_t) (((uint32_t) PWM_DUTY * (TimerPeriod - 1)) / 100);
/* Compute CCR3 value to generate a duty cycle at 25% for channel 3 and 3N */
Channel3Pulse = (uint16_t) (((uint32_t) PWM_DUTY * (TimerPeriod - 1)) / 100);
//TIM_DeInit(TIM1);
/* Time Base configuration */
TIM_TimeBaseStructure.TIM_Prescaler = TIM_PSCReloadMode_Update;
//TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;//
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_CenterAligned2;
TIM_TimeBaseStructure.TIM_Period = TimerPeriod;
TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;
TIM_TimeBaseStructure.TIM_RepetitionCounter = 0;
TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure);
/*
TIM_ClearFlag(TIM1, TIM_FLAG_Update);
TIM_ITConfig(TIM1,TIM_IT_Update, ENABLE);
NVIC_InitStructure.NVIC_IRQChannel = TIM1_UP_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x00;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x02;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
*/
/* Channel 1, 2, 3 Configuration in PWM mode */
#if USE_HARD_PWM
/**
TIM_OCMode_PWM1 PWM模式1
在向上计数时，一旦TIMx_CNT<TIMx_CCR1时通道1为有效电平，否则为无效电平
在向下计数时，一旦TIMx_CNT>TIMx_CCR1时通道1为无效电平(OC1REF=0)，否则为有效 电平(OC1REF=1)。
TIM_OCMode_PWM2 PWM模式2
在向上计数时，一旦TIMx_CNT<TIMx_CCR1时通道1为无效电平，否则为有效电平
在向下计数时，一旦TIMx_CNT>TIMx_CCR1时通道1为有效电平，否则为无效电平。
*/
TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
TIM_OCInitStructure.TIM_OutputNState = TIM_OutputNState_Enable;
TIM_OCInitStructure.TIM_Pulse = Channel1Pulse;
TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
TIM_OCInitStructure.TIM_OCNPolarity = TIM_OCPolarity_High;
TIM_OCInitStructure.TIM_OCIdleState = TIM_OCIdleState_Reset;
TIM_OCInitStructure.TIM_OCNIdleState = TIM_OCIdleState_Reset;
TIM_OC1Init(TIM1, &TIM_OCInitStructure);
TIM_OCInitStructure.TIM_Pulse = Channel2Pulse;
TIM_OC2Init(TIM1, &TIM_OCInitStructure);
TIM_OCInitStructure.TIM_Pulse = Channel3Pulse;
TIM_OC3Init(TIM1, &TIM_OCInitStructure);
TIM_OC1PreloadConfig(TIM1,TIM_OCPreload_Enable);
TIM_OC2PreloadConfig(TIM1,TIM_OCPreload_Enable);
TIM_OC3PreloadConfig(TIM1,TIM_OCPreload_Enable);
#endif
#if SVPWM_USE_BDT
TIM_BDTRInitStructure.TIM_OSSRState = TIM_OSSRState_Enable;
TIM_BDTRInitStructure.TIM_OSSIState = TIM_OSSIState_Enable;
TIM_BDTRInitStructure.TIM_LOCKLevel = TIM_LOCKLevel_OFF;
TIM_BDTRInitStructure.TIM_DeadTime = 30;
TIM_BDTRInitStructure.TIM_Break = TIM_Break_Disable;
TIM_BDTRInitStructure.TIM_BreakPolarity = TIM_BreakPolarity_Low;
TIM_BDTRInitStructure.TIM_AutomaticOutput = TIM_AutomaticOutput_Disable;
TIM_BDTRConfig(TIM1, &TIM_BDTRInitStructure);
#endif
TIM_CCPreloadControl(TIM1,ENABLE);
/* TIM1 counter enable */
TIM_Cmd(TIM1, ENABLE);
/* TIM1 Main Output Enable */
TIM_CtrlPWMOutputs(TIM1, ENABLE);
}
void pwm_init(void){
pwm_rcc_init();
pwm_pin_init();
pwm_cnt_irq_init();
pwm_tim_init();
}
int32_t get_pwm_period(void){
return (int32_t)((SYS_FRQ / PWM_FRQ ) - 1);
}
void pwm_reset_duty_cnt(uint8_t index, int16_t cnt){
if(cnt <= 0){
cnt = get_pwm_period()/2;
}
switch(index){
case 1:
TIM1->CCR1 = (uint16_t)cnt;
break;
case 2:
TIM1->CCR2 = (uint16_t)cnt;
break;
case 3:
TIM1->CCR3 = (uint16_t)cnt;
break;
}
}
void pwm_disable(void){
TIM_CtrlPWMOutputs(TIM1, DISABLE);
}
void pwm_enable(void){
TIM_CtrlPWMOutputs(TIM1, ENABLE);
}
以上代码主要实现以下几个功能；
- IM1定时器时钟，使用中央对齐模式1，则会产生上溢信号；
- PWM模式设置为
TIM_OCMode_PWM1； - 加入了死区；
- 占空比 50%；
具体如下图所示；
参考
http://www.stmcu.org.cn/module/forum/thread-613602-1-1.html
