Idelay进行时序调节
IODELAY_GROUP
# PART is virtexu xcvu440flga2892
############################################################
# Clock Period Constraints #
############################################################
############################################################
# RX Clock period Constraints (per instance) #
############################################################
# Receiver clock period constraints: please do not relax
create_clock -period 8 [get_ports rgmii_rxc]
#
####
#######
##########
#############
#################
#BLOCK CONSTRAINTS
############################################################
# Physical Interface Constraints
############################################################
############################################################
# The following are required to maximise setup/hold #
############################################################
set_property SLEW FAST [get_ports {rgmii_txd[3] rgmii_txd[2] rgmii_txd[1] rgmii_txd[0] rgmii_tx_ctl rgmii_txc}]
############################################################
# RGMII: IODELAY Constraints
############################################################
# Please modify the value of the IDELAY_VALUE/ODELAY_VALUE
# according to your design.
# For more information on IDELAYCTRL and IODELAY, please
# refer to the User Guide.
#
# Apply the same DELAY_VALUE to all RGMII RX inputs.
# DELAY_VALUE is the time represenatation of the desired delay in ps
# This is to provide a similiar Clock Path and Data Path delay.
set_property DELAY_VALUE 900 [get_cells {rgmii_interface/delay_rgmii_rx* rgmii_interface/rxdata_bus[*].delay_rgmii_rx*}]
# Group IODELAY components
set_property IODELAY_GROUP tri_mode_ethernet_mac_iodelay_grp [get_cells {rgmii_interface/delay_rgmii_tx* rgmii_interface/txdata_out_bus[*].delay_rgmii_tx*}]
set_property IODELAY_GROUP tri_mode_ethernet_mac_iodelay_grp [get_cells {rgmii_interface/delay_rgmii_rx* rgmii_interface/rxdata_bus[*].delay_rgmii_rx*}]
//------------------------------------------------------------------------------
// File : tri_mode_ethernet_mac_0_rgmii_v2_0_if.v
// Author : Xilinx Inc.
// -----------------------------------------------------------------------------
// (c) Copyright 2013 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
// -----------------------------------------------------------------------------
// Description: This module creates a version 2.0 Reduced Gigabit Media
// Independent Interface (RGMII v2.0) by instantiating
// Input/Output buffers and Input/Output double data rate
// (DDR) flip-flops as required.
//
// This interface is used to connect the Ethernet MAC to
// an external Ethernet PHY.
// This module routes the rgmii_rxc from the phy chip
// (via a bufg) onto the rx_clk line.
//------------------------------------------------------------------------------
`timescale 1 ps / 1 ps
//------------------------------------------------------------------------------
// The module declaration for the PHY IF design.
//------------------------------------------------------------------------------
module tri_mode_ethernet_mac_0_rgmii_v2_0_if (
// Synchronous resets
input tx_reset,
input rx_reset,
// The following ports are the MDIO physical interface: these will be
// pins on the FPGA
inout mdio,
output mdc,
// The following ports are the internal connections from IOB logic to
// the TEMAC core for the MDIO
output mdio_i,
input mdio_o,
input mdio_t,
input mdc_i,
// Current operating speed is 10/100
input speedis10100,
// The following ports are the RGMII physical interface: these will be at
// pins on the FPGA
output [3:0] rgmii_txd,
output rgmii_tx_ctl,
output rgmii_txc,
input [3:0] rgmii_rxd,
input rgmii_rx_ctl,
input rgmii_rxc,
// The following signals are in the RGMII in-band status signals
output reg link_status,
output reg [1:0] clock_speed,
output reg duplex_status,
// The following ports are the internal GMII connections from IOB logic
// to the TEMAC core
input phy_tx_enable,
input phy_tx_enable_falling,
input [7:0] txd_from_mac,
input tx_en_from_mac,
input tx_er_from_mac,
input tx_clk,
input clk_div5,
input clk_div5_shift,
output [7:0] rxd_to_mac,
output rx_dv_to_mac,
output rx_er_to_mac,
// Receiver clock for the MAC and Client Logic
output rx_clk
);
//----------------------------------------------------------------------------
// internal signals
//----------------------------------------------------------------------------
wire [3:0] rgmii_txd_obuf;
wire rgmii_tx_ctl_obuf;
wire rgmii_txc_obuf;
wire [3:0] rgmii_rxd_ibuf;
wire rgmii_rx_ctl_ibuf;
wire rgmii_rxc_ibuf;
reg [3:0] gmii_txd_falling; // gmii_txd signal registered on the falling edge of tx_clk.
wire delay_rgmii_tx_clk_out;
wire delay_rgmii_tx_clk_return;
wire rgmii_txc_odelay; // RGMII receiver clock ODDR output.
wire rgmii_tx_ctl_odelay; // RGMII control signal ODDR output.
wire [3:0] rgmii_txd_odelay; // RGMII data ODDR output.
wire rgmii_tx_ctl_int; // Internal RGMII transmit control signal.
wire rgmii_rx_ctl_delay;
wire [3:0] rgmii_rxd_delay;
wire rx_clk_int;
wire rx_clk_iddr;
wire rgmii_rx_ctl_reg; // Internal RGMII receiver control signal.
reg tx_en_to_ddr;
wire tx_en_to_ddr_fall;
reg tx_en_to_ddr_lch;
wire gmii_rx_dv_reg; // gmii_rx_dv registered in IOBs.
wire gmii_rx_er_reg; // gmii_rx_er registered in IOBs.
wire [7:0] gmii_rxd_reg; // gmii_rxd registered in IOBs.
wire inband_ce; // RGMII inband status registers clock enable
//----------------------------------------------------------------------------
// Input/Output Buffers
//----------------------------------------------------------------------------
// MDIO
//--------
IOBUF mdio_iobuf (
.I (mdio_o),
.IO (mdio),
.O (mdio_i),
.T (mdio_t)
);
// Route through the MDC clock
OBUF mdc_obuf_i (
.I (mdc_i),
.O (mdc)
);
// RGMII
//--------
OBUF rgmii_txc_obuf_i (
.I (rgmii_txc_obuf),
.O (rgmii_txc)
);
OBUF rgmii_tx_ctl_obuf_i (
.I (rgmii_tx_ctl_obuf),
.O (rgmii_tx_ctl)
);
genvar loopa;
generate for (loopa=0; loopa<4; loopa=loopa+1)
begin : obuf_data
OBUF rgmii_txd_obuf_i (
.I (rgmii_txd_obuf[loopa]),
.O (rgmii_txd[loopa])
);
end
endgenerate
(* DONT_TOUCH = "yes" *) IBUF rgmii_rxc_ibuf_i (
.I (rgmii_rxc),
.O (rgmii_rxc_ibuf)
);
(* DONT_TOUCH = "yes" *) IBUF rgmii_rx_ctl_ibuf_i (
.I (rgmii_rx_ctl),
.O (rgmii_rx_ctl_ibuf)
);
genvar loopi;
generate for (loopi=0; loopi<4; loopi=loopi+1)
begin : ibuf_data
IBUF rgmii_rxd_ibuf_i (
.I (rgmii_rxd[loopi]),
.O (rgmii_rxd_ibuf[loopi])
);
end
endgenerate
//----------------------------------------------------------------------------
// Route internal signals to output ports
//----------------------------------------------------------------------------
assign rxd_to_mac = gmii_rxd_reg;
assign rx_dv_to_mac = gmii_rx_dv_reg;
assign rx_er_to_mac = gmii_rx_er_reg;
//----------------------------------------------------------------------------
// RGMII Transmitter Clock Management
//----------------------------------------------------------------------------
// Delay the transmitter clock relative to the data.
// For 1 gig operation this delay is set to produce a 90 degree phase
// shifted clock w.r.t. gtx_clk_bufg so that the clock edges are
// centralised within the rgmii_txd[3:0] valid window.
// Instantiate the Output DDR primitive
ODDRE1 #(
.SRVAL (1'b0)
) rgmii_txc_ddr (
.Q (rgmii_txc_odelay),
.C (tx_clk),
.D1 (clk_div5_shift),
.D2 (clk_div5),
.SR (tx_reset)
);
// Instantiate the Output Delay primitive (delay output by 2 ns). In order to
// achieve 2ns, an ODELAY is cascaded with an IDELAY from the bitslice
// immediately below it.
ODELAYE3 #(
.DELAY_VALUE (875),
.DELAY_TYPE ("FIXED"),
.CASCADE ("MASTER"),
.REFCLK_FREQUENCY (333.333),
.SIM_DEVICE ("ULTRASCALE")
)
delay_rgmii_tx_clk (
.ODATAIN (rgmii_txc_odelay),
.DATAOUT (rgmii_txc_obuf),
.CLK (1'b0),
.CE (1'b0),
.INC (1'b0),
.CNTVALUEIN (9'h0),
.CNTVALUEOUT (),
.LOAD (1'b0),
.RST (1'b0),
.CASC_IN (1'b0),
.CASC_RETURN (delay_rgmii_tx_clk_casc_return),
.CASC_OUT (delay_rgmii_tx_clk_casc_out),
.EN_VTC (1'b1)
);
IDELAYE3 #(
.DELAY_VALUE (0),
.DELAY_TYPE ("FIXED"),
.CASCADE ("SLAVE_END"),
.REFCLK_FREQUENCY (333.333),
.SIM_DEVICE ("ULTRASCALE")
)
delay_rgmii_tx_clk_casc (
.IDATAIN (1'b0),
.DATAOUT (delay_rgmii_tx_clk_casc_return),
.DATAIN (1'b0),
.CLK (1'b0),
.CE (1'b0),
.INC (1'b0),
.CNTVALUEIN (9'h0),
.CNTVALUEOUT (),
.LOAD (1'b0),
.RST (1'b0),
.CASC_IN (delay_rgmii_tx_clk_casc_out),
.CASC_RETURN (1'b0),
.CASC_OUT (),
.EN_VTC (1'b1)
);
//---------------------------------------------------------------------------
// RGMII Transmitter Logic :
// drive TX signals through IOBs onto RGMII interface
//---------------------------------------------------------------------------
// Encode rgmii ctl signal
assign rgmii_tx_ctl_int = tx_en_from_mac ^ tx_er_from_mac;
// Instantiate Double Data Rate Output components. Then
// put data and control signals through ODELAY components to
// provide similiar net delays to those seen on the clk signal.
always @ (speedis10100, txd_from_mac)
begin
if (speedis10100 == 1'b0)
gmii_txd_falling <= txd_from_mac[7:4];
else
gmii_txd_falling <= txd_from_mac[3:0];
end
genvar i;
generate for (i=0; i<4; i=i+1)
begin : txdata_out_bus
ODDRE1 #(
.SRVAL (1'b0)
)
rgmii_txd_out (
.Q (rgmii_txd_odelay[i]),
.C (tx_clk),
.D1 (txd_from_mac[i]),
.D2 (gmii_txd_falling[i]),
.SR (tx_reset)
);
ODELAYE3 #(
.DELAY_VALUE (0),
.DELAY_TYPE ("FIXED"),
.REFCLK_FREQUENCY (333.333),
.SIM_DEVICE ("ULTRASCALE")
)
delay_rgmii_txd (
.ODATAIN (rgmii_txd_odelay[i]),
.DATAOUT (rgmii_txd_obuf[i]),
.CLK (1'b0),
.CE (1'b0),
.INC (1'b0),
.CNTVALUEIN (9'h0),
.CNTVALUEOUT (),
.LOAD (1'b0),
.RST (1'b0),
.CASC_IN (1'b0),
.CASC_RETURN (1'b0),
.CASC_OUT (),
.EN_VTC (1'b1)
);
end
endgenerate
// when the speed switches to 10/100 tx_clk is running much faster than
// txc and therefore the ddr needs to be controlled to prevent updates
// occuring at tx_clk rate
always @(posedge tx_clk)
begin
if(tx_reset) begin
tx_en_to_ddr_lch <= 1'b0;
end
else begin
if(phy_tx_enable | clk_div5) begin
tx_en_to_ddr_lch <= tx_en_from_mac;
end
else if(!clk_div5 & clk_div5_shift) begin
tx_en_to_ddr_lch <= rgmii_tx_ctl_int;
end
else begin
tx_en_to_ddr_lch <= tx_en_to_ddr_lch;
end
end
end
always @(speedis10100 or phy_tx_enable or clk_div5 or clk_div5_shift or tx_en_from_mac or rgmii_tx_ctl_int or tx_en_to_ddr_lch)
begin
if( !speedis10100 | (speedis10100 & (phy_tx_enable | clk_div5)))begin
tx_en_to_ddr = tx_en_from_mac;
end
else if( speedis10100 & (!clk_div5 & clk_div5_shift)) begin
tx_en_to_ddr = rgmii_tx_ctl_int;
end
else begin
tx_en_to_ddr = tx_en_to_ddr_lch;
end
end
assign tx_en_to_ddr_fall = speedis10100 ? tx_en_to_ddr :rgmii_tx_ctl_int;
ODDRE1 #(
.SRVAL (1'b0)
)
ctl_output (
.Q (rgmii_tx_ctl_odelay),
.C (tx_clk),
.D1 (tx_en_to_ddr),
.D2 (tx_en_to_ddr_fall),
.SR (tx_reset)
);
ODELAYE3 #(
.DELAY_VALUE (0),
.DELAY_TYPE ("FIXED"),
.REFCLK_FREQUENCY (333.333),
.SIM_DEVICE ("ULTRASCALE")
)
delay_rgmii_tx_ctl (
.ODATAIN (rgmii_tx_ctl_odelay),
.DATAOUT (rgmii_tx_ctl_obuf),
.CLK (1'b0),
.CE (1'b0),
.INC (1'b0),
.CNTVALUEIN (9'h0),
.CNTVALUEOUT (),
.LOAD (1'b0),
.RST (1'b0),
.CASC_IN (1'b0),
.CASC_RETURN (1'b0),
.CASC_OUT (),
.EN_VTC (1'b1)
);
//---------------------------------------------------------------------------
// RGMII Receiver Clock Logic
//---------------------------------------------------------------------------
// Route rgmii_rxc through a BUFG and onto clock routing
BUFG
bufg_rgmii_rx_clk (
.I (rgmii_rxc_ibuf),
.O (rx_clk_int)
);
// Route rgmii_rxc through a BUFG for connecting to IDDR components
BUFG
bufg_rgmii_rx_clk_iddr (
.I (rgmii_rxc_ibuf),
.O (rx_clk_iddr)
);
// Assign the internal clock signal to the output port
assign rx_clk = rx_clk_int;
//---------------------------------------------------------------------------
// RGMII Receiver Logic : receive signals through IOBs from RGMII interface
//---------------------------------------------------------------------------
// Drive input RGMII Rx signals from PADS through IODELAYS.
// Please modify the IODELAY_VALUE according to your design.
// For more information on IDELAYCTRL and IODELAY, please refer to
// the User Guide.
IDELAYE3 #(
.DELAY_TYPE ("FIXED"),
.REFCLK_FREQUENCY (333.333),
.SIM_DEVICE ("ULTRASCALE")
)
delay_rgmii_rx_ctl (
.IDATAIN (rgmii_rx_ctl_ibuf),
.DATAOUT (rgmii_rx_ctl_delay),
.DATAIN (1'b0),
.CLK (1'b0),
.CE (1'b0),
.INC (1'b0),
.CNTVALUEIN (9'h0),
.CNTVALUEOUT (),
.LOAD (1'b0),
.RST (1'b0),
.CASC_IN (1'b0),
.CASC_RETURN (1'b0),
.CASC_OUT (),
.EN_VTC (1'b1)
);
genvar j;
generate for (j=0; j<4; j=j+1)
begin : rxdata_bus
IDELAYE3 #(
.DELAY_TYPE ("FIXED"),
.REFCLK_FREQUENCY (333.333),
.SIM_DEVICE ("ULTRASCALE")
)
delay_rgmii_rxd (
.IDATAIN (rgmii_rxd_ibuf[j]),
.DATAOUT (rgmii_rxd_delay[j]),
.DATAIN (1'b0),
.CLK (1'b0),
.CE (1'b0),
.INC (1'b0),
.CNTVALUEIN (9'h0),
.CNTVALUEOUT (),
.LOAD (1'b0),
.RST (1'b0),
.CASC_IN (1'b0),
.CASC_RETURN (1'b0),
.CASC_OUT (),
.EN_VTC (1'b1)
);
end
endgenerate
// Instantiate Double Data Rate Input flip-flops.
// DDR_CLK_EDGE attribute specifies output data alignment from IDDR component
genvar k;
generate for (k=0; k<4; k=k+1)
begin : rxdata_in_bus
IDDRE1 #(
.DDR_CLK_EDGE ("SAME_EDGE_PIPELINED")
)
rgmii_rx_data_in (
.Q1 (gmii_rxd_reg[k]),
.Q2 (gmii_rxd_reg[k+4]),
.C (rx_clk_iddr),
.CB (!rx_clk_iddr),
.D (rgmii_rxd_delay[k]),
.R (1'b0)
);
end
endgenerate
IDDRE1 #(
.DDR_CLK_EDGE ("SAME_EDGE_PIPELINED")
)
rgmii_rx_ctl_in (
.Q1 (gmii_rx_dv_reg),
.Q2 (rgmii_rx_ctl_reg),
.C (rx_clk_iddr),
.CB (!rx_clk_iddr),
.D (rgmii_rx_ctl_delay),
.R (1'b0)
);
// Decode gmii_rx_er signal
assign gmii_rx_er_reg = gmii_rx_dv_reg ^ rgmii_rx_ctl_reg;
//----------------------------------------------------------------------------
// RGMII Inband Status Registers
// extract the inband status from received rgmii data
//----------------------------------------------------------------------------
// Enable inband status registers during Interframe Gap
assign inband_ce = !(gmii_rx_dv_reg || gmii_rx_er_reg);
always @ (posedge rx_clk_int)
begin
if (rx_reset) begin
link_status <= 1'b0;
clock_speed[1:0] <= 2'b0;
duplex_status <= 1'b0;
end
else if (inband_ce) begin
link_status <= gmii_rxd_reg[0];
clock_speed[1:0] <= gmii_rxd_reg[2:1];
duplex_status <= gmii_rxd_reg[3];
end
end
endmodule
//------------------------------------------------------------------------------
// Title : Transmitter Clock Generator
// Project : Tri-Mode Ethernet MAC
//------------------------------------------------------------------------------
// File : tri_mode_ethernet_mac_0_clk_en_gen.v
// Author : Xilinx Inc.
// -----------------------------------------------------------------------------
// (c) Copyright 2009 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
// -----------------------------------------------------------------------------
// Description: This module provides clock enables for the tx
// logic and clocks to be used in the generation of rgmii_txc.
// At 1G the enables are both set to 1 as they are not reuired, at 100M
// the enables occur every 5th cycle for the phy interface and every 10th for
// the client. At 10M this changes to every 50th and every 100th respectively.
// The clk_div5 outputs are used purely to generate the txc output and are
// used as data inputs to the DDR logic.
//------------------------------------------------------------------------------
`timescale 1 ps/1 ps
module tri_mode_ethernet_mac_0_clk_en_gen
(
input reset,
input speed_is_10_100,
input speed_is_100,
input clk,
output reg client_tx_enable,
output reg phy_tx_enable,
output reg phy_tx_enable_falling,
output reg clk_div5,
output reg clk_div5_shift
);
reg [5:0] counter;
reg [5:0] wrap_point;
reg [5:0] first_edge;
reg [5:0] second_edge;
reg div_2;
wire speed_is_10_100_int;
wire speed_is_100_int;
reg clk_div5_int;
reg clk_div5_shift_int;
// locally sync the speed controls
tri_mode_ethernet_mac_0_block_sync_block txspeedis10100gen (
.clk (clk),
.data_in (speed_is_10_100),
.data_out (speed_is_10_100_int)
);
tri_mode_ethernet_mac_0_block_sync_block txspeedis100gen (
.clk (clk),
.data_in (speed_is_100),
.data_out (speed_is_100_int)
);
// generate a 6 bit counter which counts to a max of 50 and then wraps
// the wrap point is dependant upon the speed setting
always @(posedge clk)
begin
if (reset) begin
counter <= 0;
end
else begin
if (counter >= wrap_point) begin
counter <= 0;
end
else begin
counter <= counter + 1;
end
end
end
always @(speed_is_10_100_int or speed_is_100_int)
begin
if (!speed_is_10_100_int) begin
wrap_point = 0;
first_edge = 0;
second_edge = 0;
end
else begin
if (speed_is_100_int) begin
wrap_point = 4;
first_edge = 1;
second_edge = 2;
end
else begin
wrap_point = 49;
first_edge = 23;
second_edge = 24;
end
end
end
// look for counter to equal wrap point - this gives the high speed
// clock enable - we want to generate a second enable every other pulse
always @(posedge clk)
begin
if (reset) begin
div_2 <= 0;
end
else begin
if (speed_is_10_100_int) begin
if (counter >= wrap_point) begin
div_2 <= !div_2;
end
end
else begin
div_2 <= 0;
end
end
end
// generate the clock enables - only if speed is not 1G
always @(posedge clk)
begin
if (reset) begin
clk_div5_int <= 0;
clk_div5_shift_int <= 0;
end
else begin
if (speed_is_10_100_int) begin
if (counter >= wrap_point) begin
clk_div5_int <= 1;
clk_div5_shift_int <= 1;
end
else if (counter == first_edge) begin
clk_div5_int <= 0;
clk_div5_shift_int <= 1;
end
else if (counter == second_edge) begin
clk_div5_int <= 0;
clk_div5_shift_int <= 0;
end
end
else begin
clk_div5_int <= 0;
clk_div5_shift_int <= 1;
end
end
end
// the pipeline delay between the MAC enable and the clock needs to be controlled
// to ensure the correct timing at the IO
always @(posedge clk)
begin
if (reset) begin
clk_div5 <= 0;
clk_div5_shift <= 0;
end
else begin
clk_div5 <= clk_div5_int;
clk_div5_shift <= clk_div5_shift_int;
end
end
always @(posedge clk)
begin
if (reset) begin
client_tx_enable <= 0;
phy_tx_enable <= 0;
end
else begin
if (counter >= wrap_point) begin
phy_tx_enable <= 1;
end
else begin
phy_tx_enable <= 0;
end
if (counter >= first_edge) begin
phy_tx_enable_falling <= 1;
end
else begin
phy_tx_enable_falling <= 0;
end
if ((counter >= wrap_point) & !div_2) begin
client_tx_enable <= 1;
end
else begin
client_tx_enable <= 0;
end
end
end
endmodule
//------------------------------------------------------------------------------
// Title : CDC Sync Block
// Project : Tri-Mode Ethernet MAC
//------------------------------------------------------------------------------
// File : tri_mode_ethernet_mac_0_block_sync_block.v
// Author : Xilinx Inc.
//------------------------------------------------------------------------------
// Description: Used on signals crossing from one clock domain to another, this
// is a multiple flip-flop pipeline, with all flops placed together
// into the same slice. Thus the routing delay between the two is
// minimum to safe-guard against metastability issues.
// -----------------------------------------------------------------------------
// (c) Copyright 2001-2013 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
// -----------------------------------------------------------------------------
`timescale 1ps / 1ps
(* dont_touch = "yes" *)
module tri_mode_ethernet_mac_0_block_sync_block #(
parameter INITIALISE = 1'b0,
parameter DEPTH = 5
)
(
input clk, // clock to be sync'ed to
input data_in, // Data to be 'synced'
output data_out // synced data
);
// Internal Signals
wire data_sync0;
wire data_sync1;
wire data_sync2;
wire data_sync3;
wire data_sync4;
(* ASYNC_REG = "TRUE", SHREG_EXTRACT = "NO" *)
FDRE #(
.INIT (INITIALISE[0])
) data_sync_reg0 (
.C (clk),
.D (data_in),
.Q (data_sync0),
.CE (1'b1),
.R (1'b0)
);
(* ASYNC_REG = "TRUE", SHREG_EXTRACT = "NO" *)
FDRE #(
.INIT (INITIALISE[0])
) data_sync_reg1 (
.C (clk),
.D (data_sync0),
.Q (data_sync1),
.CE (1'b1),
.R (1'b0)
);
(* ASYNC_REG = "TRUE", SHREG_EXTRACT = "NO" *)
FDRE #(
.INIT (INITIALISE[0])
) data_sync_reg2 (
.C (clk),
.D (data_sync1),
.Q (data_sync2),
.CE (1'b1),
.R (1'b0)
);
(* ASYNC_REG = "TRUE", SHREG_EXTRACT = "NO" *)
FDRE #(
.INIT (INITIALISE[0])
) data_sync_reg3 (
.C (clk),
.D (data_sync2),
.Q (data_sync3),
.CE (1'b1),
.R (1'b0)
);
(* ASYNC_REG = "TRUE", SHREG_EXTRACT = "NO" *)
FDRE #(
.INIT (INITIALISE[0])
) data_sync_reg4 (
.C (clk),
.D (data_sync3),
.Q (data_sync4),
.CE (1'b1),
.R (1'b0)
);
assign data_out = data_sync4;
endmodule
//------------------------------------------------------------------------------
// Title : Verilog Support Level Module
// File : tri_mode_ethernet_mac_0_support.v
// Author : Xilinx Inc.
// -----------------------------------------------------------------------------
// (c) Copyright 2013 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
// -----------------------------------------------------------------------------
// Description: This module holds the support level for the Tri-Mode
// Ethernet MAC IP. It contains potentially shareable FPGA
// resources such as clocking, reset and IDELAYCTRL logic.
// This can be used as-is in a single core design, or adapted
// for use with multi-core implementations.
//------------------------------------------------------------------------------
`timescale 1 ps/1 ps
//------------------------------------------------------------------------------
// The entity declaration for the block support level
//------------------------------------------------------------------------------
module tri_mode_ethernet_mac_0_support
(
input gtx_clk,
// Reference clock for IDELAYCTRL's
input refclk,
// asynchronous reset
input glbl_rstn,
input rx_axi_rstn,
input tx_axi_rstn,
// Receiver Interface
//--------------------------
output [27:0] rx_statistics_vector,
output rx_statistics_valid,
output rx_mac_aclk,
output rx_reset,
output [7:0] rx_axis_mac_tdata,
output rx_axis_mac_tvalid,
output rx_axis_mac_tlast,
output rx_axis_mac_tuser,
output [4:0] rx_axis_filter_tuser,
// Transmitter Interface
//-----------------------------
input [7:0] tx_ifg_delay,
output [31:0] tx_statistics_vector,
output tx_statistics_valid,
output tx_mac_aclk,
output tx_reset,
input [7:0] tx_axis_mac_tdata,
input tx_axis_mac_tvalid,
input tx_axis_mac_tlast,
input tx_axis_mac_tuser,
output tx_axis_mac_tready,
// MAC Control Interface
//----------------------
input pause_req,
input [15:0] pause_val,
output speedis100,
output speedis10100,
// RGMII Interface
//----------------
output [3:0] rgmii_txd,
output rgmii_tx_ctl,
output rgmii_txc,
input [3:0] rgmii_rxd,
input rgmii_rx_ctl,
input rgmii_rxc,
output inband_link_status,
output [1:0] inband_clock_speed,
output inband_duplex_status,
// MDIO Interface
//---------------
inout mdio,
output mdc,
// AXI-Lite Interface
//---------------
input s_axi_aclk,
input s_axi_resetn,
input [11:0] s_axi_awaddr,
input s_axi_awvalid,
output s_axi_awready,
input [31:0] s_axi_wdata,
input s_axi_wvalid,
output s_axi_wready,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
input [11:0] s_axi_araddr,
input s_axi_arvalid,
output s_axi_arready,
output [31:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rvalid,
input s_axi_rready,
output mac_irq
);
//----------------------------------------------------------------------------
// Shareable logic
//----------------------------------------------------------------------------
// Instantiate the sharable reset logic
tri_mode_ethernet_mac_0_support_resets tri_mode_ethernet_mac_support_resets_i (
.glbl_rstn (glbl_rstn),
.refclk (refclk),
.idelayctrl_ready (1'b1),
.idelayctrl_reset_out (idelayctrl_reset) );
// An IDELAYCTRL primitive needs to be instantiated for the Fixed Tap Delay
// mode of the IDELAY.
IDELAYCTRL #(
.SIM_DEVICE ("ULTRASCALE")
)
tri_mode_ethernet_mac_idelayctrl_common_i (
.RDY (idelayctrl_ready),
.REFCLK (refclk),
.RST (idelayctrl_reset)
);
//---------------------------------------------------------------------------
// Instantiate the TEMAC core block
//---------------------------------------------------------------------------
tri_mode_ethernet_mac_0_block tri_mode_ethernet_mac_i(
.gtx_clk (gtx_clk),
// asynchronous reset
.glbl_rstn (glbl_rstn),
.rx_axi_rstn (rx_axi_rstn),
.tx_axi_rstn (tx_axi_rstn),
// Receiver Interface
//--------------------------
.rx_statistics_vector (rx_statistics_vector),
.rx_statistics_valid (rx_statistics_valid),
.rx_mac_aclk (rx_mac_aclk),
.rx_reset (rx_reset),
.rx_axis_mac_tdata (rx_axis_mac_tdata),
.rx_axis_mac_tvalid (rx_axis_mac_tvalid),
.rx_axis_mac_tlast (rx_axis_mac_tlast),
.rx_axis_mac_tuser (rx_axis_mac_tuser),
.rx_axis_filter_tuser (rx_axis_filter_tuser),
// Transmitter Interface
//-----------------------------
.tx_ifg_delay (tx_ifg_delay),
.tx_statistics_vector (tx_statistics_vector),
.tx_statistics_valid (tx_statistics_valid),
.tx_mac_aclk (tx_mac_aclk),
.tx_reset (tx_reset),
.tx_axis_mac_tdata (tx_axis_mac_tdata),
.tx_axis_mac_tvalid (tx_axis_mac_tvalid),
.tx_axis_mac_tlast (tx_axis_mac_tlast),
.tx_axis_mac_tuser (tx_axis_mac_tuser),
.tx_axis_mac_tready (tx_axis_mac_tready),
// MAC Control Interface
//----------------------
.pause_req (pause_req),
.pause_val (pause_val),
.speedis100 (speedis100),
.speedis10100 (speedis10100),
// RGMII Interface
//----------------
.rgmii_txd (rgmii_txd),
.rgmii_tx_ctl (rgmii_tx_ctl),
.rgmii_txc (rgmii_txc),
.rgmii_rxd (rgmii_rxd),
.rgmii_rx_ctl (rgmii_rx_ctl),
.rgmii_rxc (rgmii_rxc),
.inband_link_status (inband_link_status),
.inband_clock_speed (inband_clock_speed),
.inband_duplex_status (inband_duplex_status),
// MDIO Interface
//---------------
.mdio (mdio),
.mdc (mdc),
// AXI-Lite Interface
//---------------
.s_axi_aclk (s_axi_aclk),
.s_axi_resetn (s_axi_resetn),
.s_axi_awaddr (s_axi_awaddr),
.s_axi_awvalid (s_axi_awvalid),
.s_axi_awready (s_axi_awready),
.s_axi_wdata (s_axi_wdata),
.s_axi_wvalid (s_axi_wvalid),
.s_axi_wready (s_axi_wready),
.s_axi_bresp (s_axi_bresp),
.s_axi_bvalid (s_axi_bvalid),
.s_axi_bready (s_axi_bready),
.s_axi_araddr (s_axi_araddr),
.s_axi_arvalid (s_axi_arvalid),
.s_axi_arready (s_axi_arready),
.s_axi_rdata (s_axi_rdata),
.s_axi_rresp (s_axi_rresp),
.s_axi_rvalid (s_axi_rvalid),
.s_axi_rready (s_axi_rready),
.mac_irq (mac_irq)
);
endmodule
# PART is virtexu xcvu440flga2892
############################################################
# Clock Period Constraints #
############################################################
############################################################
# RX Clock period Constraints (per instance) #
############################################################
# Receiver clock period constraints: please do not relax
create_clock -period 8 [get_ports rgmii_rxc]
#
####
#######
##########
#############
#################
#BLOCK CONSTRAINTS
############################################################
# Physical Interface Constraints
############################################################
############################################################
# The following are required to maximise setup/hold #
############################################################
set_property SLEW FAST [get_ports {rgmii_txd[3] rgmii_txd[2] rgmii_txd[1] rgmii_txd[0] rgmii_tx_ctl rgmii_txc}]
############################################################
# RGMII: IODELAY Constraints
############################################################
# Please modify the value of the IDELAY_VALUE/ODELAY_VALUE
# according to your design.
# For more information on IDELAYCTRL and IODELAY, please
# refer to the User Guide.
#
# Apply the same DELAY_VALUE to all RGMII RX inputs.
# DELAY_VALUE is the time represenatation of the desired delay in ps
# This is to provide a similiar Clock Path and Data Path delay.
set_property DELAY_VALUE 900 [get_cells {tri_mode_ethernet_mac_i/rgmii_interface/delay_rgmii_rx* tri_mode_ethernet_mac_i/rgmii_interface/rxdata_bus[*].delay_rgmii_rx*}]
# Group IODELAY components
set_property IODELAY_GROUP tri_mode_ethernet_mac_iodelay_grp [get_cells {tri_mode_ethernet_mac_i/rgmii_interface/delay_rgmii_tx* tri_mode_ethernet_mac_i/rgmii_interface/txdata_out_bus[*].delay_rgmii_tx*}]
set_property IODELAY_GROUP tri_mode_ethernet_mac_iodelay_grp [get_cells {tri_mode_ethernet_mac_i/rgmii_interface/delay_rgmii_rx* tri_mode_ethernet_mac_i/rgmii_interface/rxdata_bus[*].delay_rgmii_rx*}]
set_property IODELAY_GROUP tri_mode_ethernet_mac_iodelay_grp [get_cells {tri_mode_ethernet_mac_idelayctrl_common_i}]
# IDELAYCTRL reset input is false path
set_false_path -to [get_pins -filter {REF_PIN_NAME =~ RST} -of [get_cells tri_mode_ethernet_mac_idelayctrl_common_i*]]
#
####
#######
##########
#############
#################
#CORE CONSTRAINTS
############################################################
# Crossing of Clock Domain Constraints: please do not edit #
############################################################
# control signal is synced separately so we want a max delay to ensure the signal has settled by the time the control signal has passed through the synch
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/flow/rx_pause/pause*to_tx_reg[*]}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/flow/tx_pause/count_set*reg}] 32 -datapath_only
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/flow/rx_pause/pause*to_tx_reg[*]}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/flow/tx_pause/pause_count*reg[*]}] 32 -datapath_only
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/flow/rx_pause/pause_req_to_tx_int_reg}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/flow/tx_pause/sync_good_rx/data_sync_reg0}] 6 -datapath_only
# set a false path for the clock path from the address filter dist rams
# the paths we care about timing are either the write interface OR the read interface
# this path is from the write to the read which should be ignored
set_false_path -from [get_cells -hierarchical -filter {NAME =~ *tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/addr_filter_top/address_filter_inst/*/DP}] -to [get_cells -hierarchical -filter {NAME =~ *tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/addr_filter_top/address_filter_inst/*addr*/bit_match*reg[*]}]
# false path due to synced control path
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*statistics_counters/rd_data_ref_reg[*]}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*statistics_counters/ip2bus_data_reg[*]}] 6 -datapath_only
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*statistics_counters/response_toggle_reg}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*statistics_counters/sync_response/data_sync_reg0}] 6 -datapath_only
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*statistics_counters/request_toggle_reg}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*statistics_counters/sync_request/data_sync_reg0}] 6 -datapath_only
############################################################
# Ignore paths to resync flops
############################################################
set_false_path -to [get_pins -filter {REF_PIN_NAME =~ PRE} -of [get_cells -hier -regexp {.*\/async_rst.*}]]
set_false_path -to [get_pins -filter {REF_PIN_NAME =~ CLR} -of [get_cells -hier -regexp {.*\/async_rst.*}]]
set_false_path -to [get_pins -filter {REF_PIN_NAME =~ PRE} -of [get_cells -hier -regexp {.*\/reset_sync.*}]]
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/addr_filter_top/addr_regs.promiscuous_mode_reg_reg}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/addr_filter_top/address_filter_inst/resync_promiscuous_mode/data_sync_reg0}] 6 -datapath_only
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/addr_filter_top/addr_regs.filter_enable_reg_reg[*]}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/addr_filter_top/address_filter_inst/address_filters[*].sync_enable/data_sync_reg0}] 6 -datapath_only
set_max_delay -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*managen/conf/update_pause_ad_int_reg}] -to [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/addr_filter_top/address_filter_inst/sync_update/data_sync_reg0}] 6 -datapath_only
# the mdio interface is clocked from the axi clock but the clock is so slow is can be considered to be data
# the data related outputs are output on the falling edge of the MDC output so both can simply be considered to be multicycle paths
set_multicycle_path 10 -setup -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*managen/mdio_enabled.miim_clk_int_reg} ] -throu [get_ports mdc]
set_multicycle_path 9 -hold -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*managen/mdio_enabled.miim_clk_int_reg} ] -throu [get_ports mdc]
set_multicycle_path 10 -setup -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*managen/mdio_enabled.phy/enable_reg_reg}] -throu [get_ports mdc]
set_multicycle_path 9 -hold -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*managen/mdio_enabled.phy/enable_reg_reg}] -throu [get_ports mdc]
set_multicycle_path 10 -setup -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*managen/mdio_enabled.phy/mdio*reg} ] -throu [get_ports mdio]
set_multicycle_path 9 -hold -from [get_cells {tri_mode_ethernet_mac_i/tri_mode_ethernet_mac_0_core/*managen/mdio_enabled.phy/mdio*reg} ] -throu [get_ports mdio]
# mdio has timing implications but slow interface so relaxed
set_false_path -to [get_cells -hier -filter {NAME =~ *managen/mdio_enabled.phy/mdio_in_reg1_reg}]
------------------------------------------------------------
clock_dedicated_route backbone
-----------------------------------------------------------
"如果时钟输入引脚需要驱动不同时钟域的CMT（MMCM/PLL）模块，那么约束CLOCK_DEDICATED_ROUTE=BACKBONE是必须的。 是什么情况会导致时钟输入与CMT不在一个时钟域呢？当一组外部接口时序，其时钟信号输入FPGA的一个I/O Bank，而相应的数据信号则在另一个I/O Bank输入，并且此时需对时钟信号进行分频，分频后的时钟用作输入数据的采集。"
---------------------------------------------------------------
xilinx的时钟架构设计
----------------------------------------------------------------
IDELAYCTRL
转载：
https://zhuanlan.zhihu.com/p/91843786
https://zhuanlan.zhihu.com/p/117290284
