LPC-Link2 调试器刷 CMSIS-DAP 和 J-Link 固件

文章目录

NXP 提供的 LPCScrypt 工具
- 我 Arch 用户或其他 Linux 发行版用户想使用怎么办？

NXP 提供的 LPCScrypt 工具

支持 Linux macOS 和 Windows
https://www.nxp.com/design/microcontrollers-developer-resources/lpcscrypt-v2-1-2:LPCSCRYPT

官网给的 Linux 版本的 lpcscrypt-2.1.2_57.x86_64.deb.bin 工具看名称是 Debian/Ubuntu 衍生版才能安装使用。

我 Arch 用户或其他 Linux 发行版用户想使用怎么办？

1. 注册 NXP 官网下载相应的 Linux 版本文件

2. 用文本编辑器打开看了下里面的内容

 #!/bin/sh
# This script was generated using Makeself 2.2.0
 
umask 077
 
CRCsum="4237188651"
MD5="6c85e5870f1db1e3c66128409ecc8cb5"
TMPROOT=${TMPDIR:=/tmp}
 
label="lpcscrypt installer"
script="./install.sh"
scriptargs=""
licensetxt=""
targetdir="installer"
filesizes="1736969"
keep="n"
quiet="n"
 
print_cmd_arg=""
if type printf > /dev/null; then
    print_cmd="printf"
elif test -x /usr/ucb/echo; then
    print_cmd="/usr/ucb/echo"
else
    print_cmd="echo"
fi
 
unset CDPATH
 
MS_Printf()
{
    $print_cmd $print_cmd_arg "$1"
}
 
MS_PrintLicense()
{
  if test x"$licensetxt" != x; then
    echo $licensetxt
    while true
    do
      MS_Printf "Please type y to accept, n otherwise: "
      read yn
      if test x"$yn" = xn; then
        keep=n
 	eval $finish; exit 1        
        break;    
      elif test x"$yn" = xy; then
        break;
      fi
    done
  fi
}
 
MS_diskspace()
{
	(
	if test -d /usr/xpg4/bin; then
		PATH=/usr/xpg4/bin:$PATH
	fi
	df -kP "$1" | tail -1 | awk '{ if ($4 ~ /%/) {print $3} else {print $4} }'
	)
}
 
MS_dd()
{
    blocks=`expr $3 / 1024`
    bytes=`expr $3 % 1024`
    dd if="$1" ibs=$2 skip=1 obs=1024 conv=sync 2> /dev/null | \
    { test $blocks -gt 0 && dd ibs=1024 obs=1024 count=$blocks ; \
      test $bytes  -gt 0 && dd ibs=1 obs=1024 count=$bytes ; } 2> /dev/null
}
 
MS_dd_Progress()
{
    if test "$noprogress" = "y"; then
        MS_dd $@
        return $?
    fi
    file="$1"
    offset=$2
    length=$3
    pos=0
    bsize=4194304
    while test $bsize -gt $length; do
        bsize=`expr $bsize / 4`
    done
    blocks=`expr $length / $bsize`
    bytes=`expr $length % $bsize`
    (
        dd bs=$offset count=0 skip=1 2>/dev/null
        pos=`expr $pos \+ $bsize`
        MS_Printf "     0%% " 1>&2
        if test $blocks -gt 0; then
            while test $pos -le $length; do
                dd bs=$bsize count=1 2>/dev/null
                pcent=`expr $length / 100`
                pcent=`expr $pos / $pcent`
                if test $pcent -lt 100; then
                    MS_Printf "\b\b\b\b\b\b\b" 1>&2
                    if test $pcent -lt 10; then
                        MS_Printf "    $pcent%% " 1>&2
                    else
                        MS_Printf "   $pcent%% " 1>&2
                    fi
                fi
                pos=`expr $pos \+ $bsize`
            done
        fi
        if test $bytes -gt 0; then
            dd bs=$bytes count=1 2>/dev/null
        fi
        MS_Printf "\b\b\b\b\b\b\b" 1>&2
        MS_Printf " 100%%  " 1>&2
    ) < "$file"
}
 
MS_Help()
{
    cat << EOH >&2
Makeself version 2.2.0
 1) Getting help or info about $0 :
  $0 --help   Print this message
  $0 --info   Print embedded info : title, default target directory, embedded script ...
  $0 --lsm    Print embedded lsm entry (or no LSM)
  $0 --list   Print the list of files in the archive
  $0 --check  Checks integrity of the archive
 
 2) Running $0 :
  $0 [options] [--] [additional arguments to embedded script]
  with following options (in that order)
  --confirm             Ask before running embedded script
  --quiet		Do not print anything except error messages
  --noexec              Do not run embedded script
  --keep                Do not erase target directory after running
			the embedded script
  --noprogress          Do not show the progress during the decompression
  --nox11               Do not spawn an xterm
  --nochown             Do not give the extracted files to the current user
  --target dir          Extract directly to a target directory
                        directory path can be either absolute or relative
  --tar arg1 [arg2 ...] Access the contents of the archive through the tar command
  --                    Following arguments will be passed to the embedded script
EOH
}
 
MS_Check()
{
    OLD_PATH="$PATH"
    PATH=${GUESS_MD5_PATH:-"$OLD_PATH:/bin:/usr/bin:/sbin:/usr/local/ssl/bin:/usr/local/bin:/opt/openssl/bin"}
	MD5_ARG=""
    MD5_PATH=`exec <&- 2>&-; which md5sum || type md5sum`
    test -x "$MD5_PATH" || MD5_PATH=`exec <&- 2>&-; which md5 || type md5`
	test -x "$MD5_PATH" || MD5_PATH=`exec <&- 2>&-; which digest || type digest`
    PATH="$OLD_PATH"
 
    if test "$quiet" = "n";then
    	MS_Printf "Verifying archive integrity..."
    fi
    offset=`head -n 498 "$1" | wc -c | tr -d " "`
    verb=$2
    i=1
    for s in $filesizes
    do
		crc=`echo $CRCsum | cut -d" " -f$i`
		if test -x "$MD5_PATH"; then
			if test `basename $MD5_PATH` = digest; then
				MD5_ARG="-a md5"
			fi
			md5=`echo $MD5 | cut -d" " -f$i`
			if test $md5 = "00000000000000000000000000000000"; then
				test x$verb = xy && echo " $1 does not contain an embedded MD5 checksum." >&2
			else
				md5sum=`MS_dd "$1" $offset $s | eval "$MD5_PATH $MD5_ARG" | cut -b-32`;
				if test "$md5sum" != "$md5"; then
					echo "Error in MD5 checksums: $md5sum is different from $md5" >&2
					exit 2
				else
					test x$verb = xy && MS_Printf " MD5 checksums are OK." >&2
				fi
				crc="0000000000"; verb=n
			fi
		fi
		if test $crc = "0000000000"; then
			test x$verb = xy && echo " $1 does not contain a CRC checksum." >&2
		else
			sum1=`MS_dd "$1" $offset $s | CMD_ENV=xpg4 cksum | awk '{print $1}'`
			if test "$sum1" = "$crc"; then
				test x$verb = xy && MS_Printf " CRC checksums are OK." >&2
			else
				echo "Error in checksums: $sum1 is different from $crc" >&2
				exit 2;
			fi
		fi
		i=`expr $i + 1`
		offset=`expr $offset + $s`
    done
    if test "$quiet" = "n";then
    	echo " All good."
    fi
}
 
UnTAR()
{
    if test "$quiet" = "n"; then
    	tar $1vf - 2>&1 || { echo Extraction failed. > /dev/tty; kill -15 $$; }
    else
 
    	tar $1f - 2>&1 || { echo Extraction failed. > /dev/tty; kill -15 $$; }
    fi
}
 
finish=true
xterm_loop=
noprogress=n
nox11=n
copy=none
ownership=y
verbose=n
 
initargs="$@"
 
while true
do
    case "$1" in
    -h | --help)
	MS_Help
	exit 0
	;;
    -q | --quiet)
	quiet=y
	noprogress=y
	shift
	;;
    --info)
	echo Identification: "$label"
	echo Target directory: "$targetdir"
	echo Uncompressed size: 3916 KB
	echo Compression: gzip
	echo Date of packaging: Wed Nov 25 13:12:38 CET 2020
	echo Built with Makeself version 2.2.0 on 
	echo Build command was: "/usr/bin/makeself \\
    \"./installer\" \\
    \"./lpcscrypt-2.1.2_57.x86_64.deb.bin\" \\
    \"lpcscrypt installer\" \\
    \"./install.sh\""
	if test x$script != x; then
	    echo Script run after extraction:
	    echo "    " $script $scriptargs
	fi
	if test x"" = xcopy; then
		echo "Archive will copy itself to a temporary location"
	fi
	if test x"n" = xy; then
	    echo "directory $targetdir is permanent"
	else
	    echo "$targetdir will be removed after extraction"
	fi
	exit 0
	;;
    --dumpconf)
	echo LABEL=\"$label\"
	echo SCRIPT=\"$script\"
	echo SCRIPTARGS=\"$scriptargs\"
	echo archdirname=\"installer\"
	echo KEEP=n
	echo COMPRESS=gzip
	echo filesizes=\"$filesizes\"
	echo CRCsum=\"$CRCsum\"
	echo MD5sum=\"$MD5\"
	echo OLDUSIZE=3916
	echo OLDSKIP=499
	exit 0
	;;
    --lsm)
cat << EOLSM
No LSM.
EOLSM
	exit 0
	;;
    --list)
	echo Target directory: $targetdir
	offset=`head -n 498 "$0" | wc -c | tr -d " "`
	for s in $filesizes
	do
	    MS_dd "$0" $offset $s | eval "gzip -cd" | UnTAR t
	    offset=`expr $offset + $s`
	done
	exit 0
	;;
	--tar)
	offset=`head -n 498 "$0" | wc -c | tr -d " "`
	arg1="$2"
    if ! shift 2; then MS_Help; exit 1; fi
	for s in $filesizes
	do
	    MS_dd "$0" $offset $s | eval "gzip -cd" | tar "$arg1" - $*
	    offset=`expr $offset + $s`
	done
	exit 0
	;;
    --check)
	MS_Check "$0" y
	exit 0
	;;
    --confirm)
	verbose=y
	shift
	;;
	--noexec)
	script=""
	shift
	;;
    --keep)
	keep=y
	shift
	;;
    --target)
	keep=y
	targetdir=${2:-.}
    if ! shift 2; then MS_Help; exit 1; fi
	;;
    --noprogress)
	noprogress=y
	shift
	;;
    --nox11)
	nox11=y
	shift
	;;
    --nochown)
	ownership=n
	shift
	;;
    --xwin)
	finish="echo Press Return to close this window...; read junk"
	xterm_loop=1
	shift
	;;
    --phase2)
	copy=phase2
	shift
	;;
    --)
	shift
	break ;;
    -*)
	echo Unrecognized flag : "$1" >&2
	MS_Help
	exit 1
	;;
    *)
	break ;;
    esac
done
 
if test "$quiet" = "y" -a "$verbose" = "y";then
	echo Cannot be verbose and quiet at the same time. >&2
	exit 1
fi
 
MS_PrintLicense
 
case "$copy" in
copy)
    tmpdir=$TMPROOT/makeself.$RANDOM.`date +"%y%m%d%H%M%S"`.$$
    mkdir "$tmpdir" || {
	echo "Could not create temporary directory $tmpdir" >&2
	exit 1
    }
    SCRIPT_COPY="$tmpdir/makeself"
    echo "Copying to a temporary location..." >&2
    cp "$0" "$SCRIPT_COPY"
    chmod +x "$SCRIPT_COPY"
    cd "$TMPROOT"
    exec "$SCRIPT_COPY" --phase2 -- $initargs
    ;;
phase2)
    finish="$finish ; rm -rf `dirname $0`"
    ;;
esac
 
if test "$nox11" = "n"; then
    if tty -s; then                 # Do we have a terminal?
	:
    else
        if test x"$DISPLAY" != x -a x"$xterm_loop" = x; then  # No, but do we have X?
            if xset q > /dev/null 2>&1; then # Check for valid DISPLAY variable
                GUESS_XTERMS="xterm rxvt dtterm eterm Eterm kvt konsole aterm"
                for a in $GUESS_XTERMS; do
                    if type $a >/dev/null 2>&1; then
                        XTERM=$a
                        break
                    fi
                done
                chmod a+x $0 || echo Please add execution rights on $0
                if test `echo "$0" | cut -c1` = "/"; then # Spawn a terminal!
                    exec $XTERM -title "$label" -e "$0" --xwin "$initargs"
                else
                    exec $XTERM -title "$label" -e "./$0" --xwin "$initargs"
                fi
            fi
        fi
    fi
fi
 
if test "$targetdir" = "."; then
    tmpdir="."
else
    if test "$keep" = y; then
	if test "$quiet" = "n";then
	    echo "Creating directory $targetdir" >&2
	fi
	tmpdir="$targetdir"
	dashp="-p"
    else
	tmpdir="$TMPROOT/selfgz$$$RANDOM"
	dashp=""
    fi
    mkdir $dashp $tmpdir || {
	echo 'Cannot create target directory' $tmpdir >&2
	echo 'You should try option --target dir' >&2
	eval $finish
	exit 1
    }
fi
 
location="`pwd`"
if test x$SETUP_NOCHECK != x1; then
    MS_Check "$0"
fi
offset=`head -n 498 "$0" | wc -c | tr -d " "`
 
if test x"$verbose" = xy; then
	MS_Printf "About to extract 3916 KB in $tmpdir ... Proceed ? [Y/n] "
	read yn
	if test x"$yn" = xn; then
		eval $finish; exit 1
	fi
fi
 
if test "$quiet" = "n";then
	MS_Printf "Uncompressing $label"
fi
res=3
if test "$keep" = n; then
    trap 'echo Signal caught, cleaning up >&2; cd $TMPROOT; /bin/rm -rf $tmpdir; eval $finish; exit 15' 1 2 3 15
fi
 
leftspace=`MS_diskspace $tmpdir`
if test -n "$leftspace"; then
    if test "$leftspace" -lt 3916; then
        echo
        echo "Not enough space left in "`dirname $tmpdir`" ($leftspace KB) to decompress $0 (3916 KB)" >&2
        if test "$keep" = n; then
            echo "Consider setting TMPDIR to a directory with more free space."
        fi
        eval $finish; exit 1
    fi
fi
 
for s in $filesizes
do
    if MS_dd_Progress "$0" $offset $s | eval "gzip -cd" | ( cd "$tmpdir"; UnTAR x ) 1>/dev/null; then
		if test x"$ownership" = xy; then
			(PATH=/usr/xpg4/bin:$PATH; cd "$tmpdir"; chown -R `id -u` .;  chgrp -R `id -g` .)
		fi
    else
		echo >&2
		echo "Unable to decompress $0" >&2
		eval $finish; exit 1
    fi
    offset=`expr $offset + $s`
done
if test "$quiet" = "n";then
	echo
fi
 
cd "$tmpdir"
res=0
if test x"$script" != x; then
    if test x"$verbose" = xy; then
		MS_Printf "OK to execute: $script $scriptargs $* ? [Y/n] "
		read yn
		if test x"$yn" = x -o x"$yn" = xy -o x"$yn" = xY; then
			eval $script $scriptargs $*; res=$?;
		fi
    else
		eval $script $scriptargs $*; res=$?
    fi
    if test $res -ne 0; then
		test x"$verbose" = xy && echo "The program '$script' returned an error code ($res)" >&2
    fi
fi
if test "$keep" = n; then
    cd $TMPROOT
    /bin/rm -rf $tmpdir
fi
eval $finish; exit $res
��6J綺燧\曽炶夯E噒ww�wI	逸澮!妸€倀wùt)J妧历击9g遱嫖湙�}蛙遺褛 箈啧y�.n�/<�.聜偪=�潲雜_�/堪牥€€ 彁///� L峥囹浪勐Cp磓urp斛7唢遻��鳢o售沦櫵塔翼�+烂/n~^~庚!�0衠[:竢[Zx賑1纞=苫果{:刭{螟xxEaZF:拷肆fT辑狜鉻祦窭頲羆搛6�0+{7綆硩厳
腆�+搪骈骀MG�=l�急l~�钷�0NNoog絾儠嶋�摰蟠眖眖觜踬9齧糪}FFV+o槑�+锟�#椃�7�纟鯙^V瀗挝�6縙u龙�开�0N;镞鴂��鹵押璱�#�'扇瘥]沖W岱o嫍F'	＇斫~#f踣访�sp+`0N{X喁痡o沆析椬{7皐饌/拲'熳碟鮹L6^0W7o樂厯
搪�鎛醝醔鉳汩E晴/忖紤濏_抉/_鸲珦珱鷦t0%7O豲W鲟渍E/讛霟}n�涫豿YXE/{[镞_秜s爹趼o凤弋氷_\砀竳抑頝v0N嘷灼滞邮営谄萜遮骒n�蔬輿搹嫍嬒LP標OD萀H€粟乞浊Y鼁嫕�7層�o禭6蝆6|%房浸窙纩桝侚�=€賉兰輅繊誳/��5嬁挖�齯�緋q記挲�+黭狍	瘕孆/(((�艆N侣邮^
胱m韅崾纠掠�鰇q线齏H@圜�颊嫃�耸驼*纡吷e例飤�熜O弫 犞f唨�5缶�4I悦痜瑡��;idb�7TF�冉Xo鳫-^髫E褚癄F�!"1遀C,賭I3)y�'铻k�%躍U�kc_淓	fB堠p┭:	�4仜,雸�5_Wx噭
�-\)z5耠�.�:jKa~)熶'Wv`轜圄^晪�'洫:蚙偵儆�WW挊莵騝壚E€�9丟7I畨C虸>E�-7
Q綗�>h碦�t靸塡斶8~
拰_V1鸃(|鸕|崎桴壟泳◣vf

前半部分是 shell 脚本从 499 行开始就是乱码了
第 437 行有这个提示：

 offset=`head -n 498 "$0" | wc -c | tr -d " "`

推测 NXP 是使用 gzexe 进行了压缩和简单的加密处理

3. 开始 lpcscrypt-2.1.2_57.x86_64.deb.bin 解密

 tail -n +499 lpcscrypt-2.1.2_57.x86_64.deb.bin > lpcscrypt-2.1.2_57.x86_64.deb

得到一个 deb 包（不知道是不是正常的 deb 包，进行下一步验证）

4. 解压 `deb` 包

 bsdtar -xf lpcscrypt-2.1.2_57.x86_64.deb

解压成功（狗头保命

5. 解压 `data.tar.gz`

 mkdir -p build
tar -xf data.tar.gz -C build

得到 NXP 的编译后的二进制文件

 tree build                    
build
├── lib
│   └── udev
│       └── rules.d
│           └── 99-lpcscrypt.rules
└── usr
    └── local
        └── lpcscrypt-2.1.2_57
            ├── bin
            │   ├── LPCScrypt_240.bin.hdr
            │   ├── image_manager
            │   └── lpcscrypt
            ├── docs
            │   ├── Debug_Probe_Firmware_Programming.pdf
            │   └── LPCScrypt_User_Guide.pdf
            ├── eula
            │   ├── SoftwareContentRegister.txt
            │   ├── licenses
            │   │   ├── Apache-2.0.txt
            │   │   ├── BSD-3-clause.txt
            │   │   ├── BSD-4-clause.txt
            │   │   ├── GPLV2.txt
            │   │   ├── LGPLV2.1.txt
            │   │   └── Zlib.txt
            │   ├── lpcscrypt_eula.docx
            │   ├── lpcscrypt_eula.rtf
            │   └── lpcscrypt_eula.txt
            ├── images
            │   ├── Link2_Fill_SPIFI.bin
            │   ├── Link2_Medium_SPIFI.bin
            │   ├── Link2_Small_SPIFI.bin
            │   ├── MCB1800_FillBlinky_BankA.bin
            │   ├── MCB1800_FillBlinky_BankB.bin
            │   ├── MCB1800_FillBlinky_SPIFI.bin
            │   ├── MCB1800_LargeBlinky_BankA.bin
            │   ├── MCB1800_LargeBlinky_BankB.bin
            │   ├── MCB1800_LargeBlinky_RAM.bin
            │   ├── MCB1800_LargeBlinky_SPIFI.bin
            │   ├── MCB1800_blinky_BankA.bin
            │   ├── MCB1800_blinky_BankB.bin
            │   ├── MCB1800_blinky_RAM.bin
            │   └── MCB1800_blinky_SPIFI.bin
            ├── probe_firmware
            │   ├── LPCLink2
            │   │   ├── Firmware_JLink_LPC-Link2_20190404.bin
            │   │   ├── LPC432x_CMSIS_DAP_NB_V5_224.bin.hdr
            │   │   ├── LPC432x_CMSIS_DAP_NB_V5_361.bin.hdr
            │   │   ├── LPC432x_CMSIS_DAP_SER_V5_224.bin.hdr
            │   │   ├── LPC432x_CMSIS_DAP_SER_V5_361.bin.hdr
            │   │   ├── LPC432x_CMSIS_DAP_V5_224.bin.hdr
            │   │   └── LPC432x_CMSIS_DAP_V5_361.bin.hdr
            │   └── LPCXpressoV2
            │       ├── Firmware_JLink_LPCXpressoV2_20190404.bin
            │       ├── LPC432x_IAP_CMSIS_DAP_NB_V5_224.bin
            │       ├── LPC432x_IAP_CMSIS_DAP_NB_V5_361.bin
            │       ├── LPC432x_IAP_CMSIS_DAP_SER_V5_224.bin
            │       ├── LPC432x_IAP_CMSIS_DAP_SER_V5_361.bin
            │       ├── LPC432x_IAP_CMSIS_DAP_V5_224.bin
            │       └── LPC432x_IAP_CMSIS_DAP_V5_361.bin
            └── scripts
                ├── 99-lpcscrypt.rules
                ├── LPCScrypt_CLI
                ├── aeskey
                ├── boot_lpcscrypt
                ├── dfu_boot
                ├── encrypt_and_program
                ├── encrypt_and_program.scy
                ├── install_udev_rules
                ├── program_CMSIS
                └── program_JLINK
 
15 directories, 54 files

6. 这下就能进行 AUR 打包处理了

按 Arch 的打包规范进行编写 PKGBUILD 打包脚本
根据 NXP 的介绍需要依赖最新版 jlink 软件包（Arch 下是 jlink-software-and-documentation 其他 Linux 可能在软件商店有，也可能没有，那就需要自行去 Segger 官网下载 Jlink 的软件包了）

 # Maintainer: taotieren <admin@taotieren.com>
# Contributor:
 
pkgname="lpcscrypt-bin"
pkgver=2.1.2
pkgrel=1
pkgdesc="LPCScrypt is the recommended tool for programming the latest versions of CMSIS-DAP and J-Link firmware onto boards with Link2/LPC-Link2 debug probes."
arch=("x86_64")
makedepends=('imagemagick')
depends=('jlink-software-and-documentation')
optdepends=()
conflicts=()
url="https://www.nxp.com/design/microcontrollers-developer-resources/lpcscrypt-v2-1-2:LPCSCRYPT"
license=('Commercial' 'Apache-2.0' 'BSD-4-clause' 'BSD-3-clause' 'LGPLV2.1' 'GPLV2' 'Zlib')
options=(!strip)
_pkgver_ext=${pkgver}_57
_pkg_file_name=${pkgname%-bin}-${_pkgver_ext}.${arch}.deb.bin
_deb_file_name=${pkgname%-bin}-${_pkgver_ext}.${arch}.deb
_DOWNLOADS_DIR=`xdg-user-dir DOWNLOAD`
if [ ! -f ${PWD}/${_pkg_file_name} ]; then
        if [ -f $_DOWNLOADS_DIR/${_pkg_file_name} ]; then
                ln -sfn $_DOWNLOADS_DIR/${_pkg_file_name} ${PWD}
        else
                msg2 ""
                msg2 "The package can be downloaded here: "
                msg2 "Please remember to put a downloaded package ${_pkg_file_name} into the build directory ${PWD} or $_DOWNLOADS_DIR"
                msg2 ""
        fi
fi
 
source=("local://${_pkg_file_name}")
sha256sums=('379c63b788a72e64571af870d760ad6b3be32e4c863d29ca58276f750e416750')
noextract=(${_pkg_file_name})
 
prepare(){
        cd "$srcdir"
    tail -n +499 ${_pkg_file_name} > ${_deb_file_name}
    mkdir -p build
    bsdtar xf ${_deb_file_name} -C build
    bsdtar xf build/${_deb_file_name} -C build
}
package() {
        cd "$srcdir"
 
        msg2 'Installing LPCScrypt'
        tar xf "build/data.tar.gz" -C "${pkgdir}/"
        mv "${pkgdir}/lib" "${pkgdir}/usr"
        msg2 'Instalation of binary file'
        install -Dm0755 /dev/stdin "${pkgdir}/usr/bin/${pkgname%-bin}" <<END
#!/bin/sh
/usr/local/lpcscrypt-2.1.2_57/bin/lpcscrypt "\$@"
END
 
        msg2 'Instalation of license file'
        install -dm0755 "${pkgdir}/usr/share/licenses/${pkgname%-bin}/"
        cp -rv  "${pkgdir}/usr/local/lpcscrypt-2.1.2_57/eula" "${pkgdir}/usr/share/licenses/${pkgname%-bin}/"
}
 
#
# makepkg --printsrcinfo > .SRCINFO
#
 
# vim: set ts=8 sw=8 tw=0 noet:

7. 编译 `PKGBUILD` 并安装验证

如果需要更新 PKGBUILD 中sha256sums 校验值

 updpkgsums

创建 .SRCINFO 文件

 makepkg --printsrcinfo > .SRCINFO

编译 PKGBUILD

 makepkg -sf                      
==> 正在创建软件包：lpcscrypt-bin 2.1.2-1 (2021年07月04日 星期日 14时04分10秒)
==> 正在检查运行时依赖关系...
==> 正在检查编译时依赖关系
==> 获取源代码...
  -> 找到 lpcscrypt-2.1.2_57.x86_64.deb.bin
==> 正在验证 source 文件，使用sha256sums...
    lpcscrypt-2.1.2_57.x86_64.deb.bin ... 通过
==> 正在释放源码...
==> 正在开始 prepare()...
==> 正在删除现存的 $pkgdir/ 目录...
==> 正在进入 fakeroot 环境...
==> 正在开始 package()...
  -> Installing LPCScrypt
  -> Instalation of binary file
  -> Instalation of license file
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/lpcscrypt_eula.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/lpcscrypt_eula.txt'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/lpcscrypt_eula.docx' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/lpcscrypt_eula.docx'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/lpcscrypt_eula.rtf' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/lpcscrypt_eula.rtf'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/Zlib.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/Zlib.txt'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/Apache-2.0.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/Apache-2.0.txt'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/GPLV2.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/GPLV2.txt'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/BSD-3-clause.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/BSD-3-clause.txt'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/BSD-4-clause.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/BSD-4-clause.txt'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/LGPLV2.1.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/LGPLV2.1.txt'
'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/SoftwareContentRegister.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/SoftwareContentRegister.txt'
==> 正在清理安装...
  -> 正在删除 libtool 文件...
  -> 正在清除不打算要的文件...
  -> 正在移除静态库文件...
  -> 正在压缩 man 及 info 文档...
==> 正在检查打包问题...
==> 正在构建软件包"lpcscrypt-bin"...
  -> 正在生成 .PKGINFO 文件...
  -> 正在生成 .BUILDINFO 文件...
  -> 正在生成 .MTREE 文件...
  -> 正在压缩软件包...
==> 正在离开 fakeroot 环境。
==> 完成创建：lpcscrypt-bin 2.1.2-1 (2021年07月04日 星期日 14时04分12秒)

安装 lpcscrypt-bin 2.1.2-1.pkg.tar.zst

 sudo pacman -U lpcscrypt-bin 2.1.2-1.pkg.tar.zst
# 或
yay -U lpcscrypt-bin 2.1.2-1.pkg.tar.zst
正在加载软件包...
正在解析依赖关系...
正在查找软件包冲突...
 
软件包 (1) lpcscrypt-bin-2.1.2-1
 
全部安装大小：  9.34 MiB
 
:: 进行安装吗？ [Y/n] 
(1/1) 正在检查密钥环里的密钥                       [##########################] 100%
(1/1) 正在检查软件包完整性                         [##########################] 100%
(1/1) 正在加载软件包文件                           [##########################] 100%
(1/1) 正在检查文件冲突                             [##########################] 100%
(1/1) 正在检查可用存储空间                         [##########################] 100%
:: 正在处理软件包的变化...
(1/1) 正在安装 lpcscrypt-bin                       [##########################] 100%
:: 正在运行事务后钩子函数...
(1/3) Reloading device manager configuration...
(2/3) Arming ConditionNeedsUpdate...
(3/3) Refreshing PackageKit...

运行并验证 lpcscrypt

 lpcscrypt
lpcscrypt: NXP LPC Scripting tool. v2.1.2 (Build 44) (Nov 25 2020 13:01:49)
usage: lpcscrypt [-d serial_port] [-e dnqst] [-g usec] [-hp] [-v var=value]
[-s script]|[-t]|[[-x] command]
where:
         -h             display this help message
         -d serial_port use 'serial_port' (device) as target
                        use ? to list available ports
         -s script      read script from file
         -t             read script from terminal (stdin)
         -x command     execute 'command' only
                        the -s, -t and -x options and/or immediate commands
                        are mutually exclusive
 
         -v name=value  assign variable 'name' the value 'value'
                        Use [name] to reference the variable in the script
                        Simple text replacement is performed on each script line
         -p             pause before each script command
         -e denqst      set command echo options:
                q - quiet  - echo nothing [default]
                d - debug  - echo additional debug information
                n - noisy  - echo everything
                s - script - echo script commands
                t - target - echo target commands
                b - buffer - dump raw target buffer
                e - exit   - display message on exit
 
Supported high-level commands (implemented by this tool) are:
    program     program [+c|+wN] (<file>|<fill_value>) <baseAddress>
                          [<fill_length>].
                          where: +c==calculate checksum
                          +wN==width of fill_value, where N is 1, 2 or 4
                program file or value into flash at baseAddress
    verify      verify [+c|+i|+wN] (<file>|<fill_value>) <baseAddress>
                          [<fill_length>].
                          where: +c==calculate checksum, +i==ignore checksum
                          +wN==width of fill_value, where N is 1, 2 or 4
                verify that flash contents matches the file or value
    erase       erase <baseAddress>
                erase flash contents
    blankCheck  blankCheck <baseAddress>
                blankcheck
    setBoot     setBoot [BankA|BankB|0|1]
                set the active boot flash bank
    setVidPid   setVidPid <vid> <pid>
                program the OTP VID and PID
    echo        echo <parameters>*
                echo all parameters to the output stream
    delay       delay <microseconds>
                delay for number of microseconds
    pause       pause [on|off] | message
                if on or off, switch autoPause on,
                        else display message and wait for <ENTER>.
                        (Not possible if script is from stdin)
    timer       timer <start|stop|print>
                start/stop a timer
    var         var name=value
                create a local variable
    <other>     Any command supported by the target
Multiple serial ports found:
/dev/ttyACM1
/dev/ttyUSB0
/dev/ttyACM0

8. 上传到 AUR 仓库

从 AUR 上创建一个空仓库：

 git clone ssh://aur@aur.archlinux.org/lpcscrypt-bin.git

添加刚才的 PKGBUILD .SRCINFO 文件到仓库中

 git add PKGBUILD 
git add .SRCINFO
cat > .gitignore << EOF
*
*.*
EOF
git add .gitignore -f
git commit -am "Update lpcscrypt-bin"
git push

https://aur.archlinux.org/packages/lpcscrypt-bin/

posted @ 2021-07-04 14:13 饕餮人阅读(40) 评论(0) 编辑收藏举报来源

刷新页面返回顶部

登录后才能查看或发表评论，立即登录或者逛逛博客园首页

相关博文：

· Arch Linux 下 sipeed longan-nano 2 rv-link

· Arch Linux stc-isp-wine AUR 包

· 清除挖矿病毒

· 高度安全环境下的高级渗透测试（全）

· Linux

阅读排行：
· 物流快递公司核心技术能力-地址解析分单基础技术分享
· .NET 10首个预览版发布：重大改进与新特性概览！
· AI与.NET技术实操系列（二）：开始使用ML.NET
· 单线程的Redis速度为什么快？
· Pantheons：用 TypeScript 打造主流大模型对话的一站式集成库

公告

昵称：饕餮人
园龄： 7年
粉丝： 0
关注： 5

+加关注

2025年3月

日

一

二

三

四

五

六

随笔分类 (2)

随笔档案 (19)

文章分类 (3)

文章档案 (1)

2024年8月(1)

饕餮人

Lifetime Learning！

Arch Linux/其他 Linux 下给 Link2/LPC-Link2 调试器刷 CMSIS-DAP 和 J-Link 固件

文章目录

NXP 提供的 LPCScrypt 工具

我 Arch 用户或其他 Linux 发行版用户想使用怎么办？

1. 注册 NXP 官网下载相应的 Linux 版本文件

2. 用文本编辑器打开看了下里面的内容

3. 开始 lpcscrypt-2.1.2_57.x86_64.deb.bin 解密

4. 解压 `deb` 包

5. 解压 `data.tar.gz`

6. 这下就能进行 AUR 打包处理了

7. 编译 `PKGBUILD` 并安装验证

8. 上传到 AUR 仓库

公告

搜索

常用链接

最新随笔

积分与排名

随笔分类 (2)

随笔档案 (19)

文章分类 (3)

文章档案 (1)

相册 (1)

阅读排行榜

	#!/bin/sh
	# This script was generated using Makeself 2.2.0

	umask 077

	CRCsum="4237188651"
	MD5="6c85e5870f1db1e3c66128409ecc8cb5"
	TMPROOT=${TMPDIR:=/tmp}

	label="lpcscrypt installer"
	script="./install.sh"
	scriptargs=""
	licensetxt=""
	targetdir="installer"
	filesizes="1736969"
	keep="n"
	quiet="n"

	print_cmd_arg=""
	if type printf > /dev/null; then
	print_cmd="printf"
	elif test -x /usr/ucb/echo; then
	print_cmd="/usr/ucb/echo"
	else
	print_cmd="echo"
	fi

	unset CDPATH

	MS_Printf()
	{
	$print_cmd $print_cmd_arg "$1"
	}

	MS_PrintLicense()
	{
	if test x"$licensetxt" != x; then
	echo $licensetxt
	while true
	do
	MS_Printf "Please type y to accept, n otherwise: "
	read yn
	if test x"$yn" = xn; then
	keep=n
	eval $finish; exit 1
	break;
	elif test x"$yn" = xy; then
	break;
	fi
	done
	fi
	}

	MS_diskspace()
	{
	(
	if test -d /usr/xpg4/bin; then
	PATH=/usr/xpg4/bin:$PATH
	fi
	df -kP "$1" \| tail -1 \| awk '{ if ($4 ~ /%/) {print $3} else {print $4} }'
	)
	}

	MS_dd()
	{
	blocks=`expr $3 / 1024`
	bytes=`expr $3 % 1024`
	dd if="$1" ibs=$2 skip=1 obs=1024 conv=sync 2> /dev/null \| \
	{ test $blocks -gt 0 && dd ibs=1024 obs=1024 count=$blocks ; \
	test $bytes -gt 0 && dd ibs=1 obs=1024 count=$bytes ; } 2> /dev/null
	}

	MS_dd_Progress()
	{
	if test "$noprogress" = "y"; then
	MS_dd $@
	return $?
	fi
	file="$1"
	offset=$2
	length=$3
	pos=0
	bsize=4194304
	while test $bsize -gt $length; do
	bsize=`expr $bsize / 4`
	done
	blocks=`expr $length / $bsize`
	bytes=`expr $length % $bsize`
	(
	dd bs=$offset count=0 skip=1 2>/dev/null
	pos=`expr $pos \+ $bsize`
	MS_Printf " 0%% " 1>&2
	if test $blocks -gt 0; then
	while test $pos -le $length; do
	dd bs=$bsize count=1 2>/dev/null
	pcent=`expr $length / 100`
	pcent=`expr $pos / $pcent`
	if test $pcent -lt 100; then
	MS_Printf "\b\b\b\b\b\b\b" 1>&2
	if test $pcent -lt 10; then
	MS_Printf " $pcent%% " 1>&2
	else
	MS_Printf " $pcent%% " 1>&2
	fi
	fi
	pos=`expr $pos \+ $bsize`
	done
	fi
	if test $bytes -gt 0; then
	dd bs=$bytes count=1 2>/dev/null
	fi
	MS_Printf "\b\b\b\b\b\b\b" 1>&2
	MS_Printf " 100%% " 1>&2
	) < "$file"
	}

	MS_Help()
	{
	cat << EOH >&2
	Makeself version 2.2.0
	1) Getting help or info about $0 :
	$0 --help Print this message
	$0 --info Print embedded info : title, default target directory, embedded script ...
	$0 --lsm Print embedded lsm entry (or no LSM)
	$0 --list Print the list of files in the archive
	$0 --check Checks integrity of the archive

	2) Running $0 :
	$0 [options] [--] [additional arguments to embedded script]
	with following options (in that order)
	--confirm Ask before running embedded script
	--quiet Do not print anything except error messages
	--noexec Do not run embedded script
	--keep Do not erase target directory after running
	the embedded script
	--noprogress Do not show the progress during the decompression
	--nox11 Do not spawn an xterm
	--nochown Do not give the extracted files to the current user
	--target dir Extract directly to a target directory
	directory path can be either absolute or relative
	--tar arg1 [arg2 ...] Access the contents of the archive through the tar command
	-- Following arguments will be passed to the embedded script
	EOH
	}

	MS_Check()
	{
	OLD_PATH="$PATH"
	PATH=${GUESS_MD5_PATH:-"$OLD_PATH:/bin:/usr/bin:/sbin:/usr/local/ssl/bin:/usr/local/bin:/opt/openssl/bin"}
	MD5_ARG=""
	MD5_PATH=`exec <&- 2>&-; which md5sum \|\| type md5sum`
	test -x "$MD5_PATH" \|\| MD5_PATH=`exec <&- 2>&-; which md5 \|\| type md5`
	test -x "$MD5_PATH" \|\| MD5_PATH=`exec <&- 2>&-; which digest \|\| type digest`
	PATH="$OLD_PATH"

	if test "$quiet" = "n";then
	MS_Printf "Verifying archive integrity..."
	fi
	offset=`head -n 498 "$1" \| wc -c \| tr -d " "`
	verb=$2
	i=1
	for s in $filesizes
	do
	crc=`echo $CRCsum \| cut -d" " -f$i`
	if test -x "$MD5_PATH"; then
	if test `basename $MD5_PATH` = digest; then
	MD5_ARG="-a md5"
	fi
	md5=`echo $MD5 \| cut -d" " -f$i`
	if test $md5 = "00000000000000000000000000000000"; then
	test x$verb = xy && echo " $1 does not contain an embedded MD5 checksum." >&2
	else
	md5sum=`MS_dd "$1" $offset $s \| eval "$MD5_PATH $MD5_ARG" \| cut -b-32`;
	if test "$md5sum" != "$md5"; then
	echo "Error in MD5 checksums: $md5sum is different from $md5" >&2
	exit 2
	else
	test x$verb = xy && MS_Printf " MD5 checksums are OK." >&2
	fi
	crc="0000000000"; verb=n
	fi
	fi
	if test $crc = "0000000000"; then
	test x$verb = xy && echo " $1 does not contain a CRC checksum." >&2
	else
	sum1=`MS_dd "$1" $offset $s \| CMD_ENV=xpg4 cksum \| awk '{print $1}'`
	if test "$sum1" = "$crc"; then
	test x$verb = xy && MS_Printf " CRC checksums are OK." >&2
	else
	echo "Error in checksums: $sum1 is different from $crc" >&2
	exit 2;
	fi
	fi
	i=`expr $i + 1`
	offset=`expr $offset + $s`
	done
	if test "$quiet" = "n";then
	echo " All good."
	fi
	}

	UnTAR()
	{
	if test "$quiet" = "n"; then
	tar $1vf - 2>&1 \|\| { echo Extraction failed. > /dev/tty; kill -15 $$; }
	else

	tar $1f - 2>&1 \|\| { echo Extraction failed. > /dev/tty; kill -15 $$; }
	fi
	}

	finish=true
	xterm_loop=
	noprogress=n
	nox11=n
	copy=none
	ownership=y
	verbose=n

	initargs="$@"

	while true
	do
	case "$1" in
	-h \| --help)
	MS_Help
	exit 0
	;;
	-q \| --quiet)
	quiet=y
	noprogress=y
	shift
	;;
	--info)
	echo Identification: "$label"
	echo Target directory: "$targetdir"
	echo Uncompressed size: 3916 KB
	echo Compression: gzip
	echo Date of packaging: Wed Nov 25 13:12:38 CET 2020
	echo Built with Makeself version 2.2.0 on
	echo Build command was: "/usr/bin/makeself \\
	\"./installer\" \\
	\"./lpcscrypt-2.1.2_57.x86_64.deb.bin\" \\
	\"lpcscrypt installer\" \\
	\"./install.sh\""
	if test x$script != x; then
	echo Script run after extraction:
	echo " " $script $scriptargs
	fi
	if test x"" = xcopy; then
	echo "Archive will copy itself to a temporary location"
	fi
	if test x"n" = xy; then
	echo "directory $targetdir is permanent"
	else
	echo "$targetdir will be removed after extraction"
	fi
	exit 0
	;;
	--dumpconf)
	echo LABEL=\"$label\"
	echo SCRIPT=\"$script\"
	echo SCRIPTARGS=\"$scriptargs\"
	echo archdirname=\"installer\"
	echo KEEP=n
	echo COMPRESS=gzip
	echo filesizes=\"$filesizes\"
	echo CRCsum=\"$CRCsum\"
	echo MD5sum=\"$MD5\"
	echo OLDUSIZE=3916
	echo OLDSKIP=499
	exit 0
	;;
	--lsm)
	cat << EOLSM
	No LSM.
	EOLSM
	exit 0
	;;
	--list)
	echo Target directory: $targetdir
	offset=`head -n 498 "$0" \| wc -c \| tr -d " "`
	for s in $filesizes
	do
	MS_dd "$0" $offset $s \| eval "gzip -cd" \| UnTAR t
	offset=`expr $offset + $s`
	done
	exit 0
	;;
	--tar)
	offset=`head -n 498 "$0" \| wc -c \| tr -d " "`
	arg1="$2"
	if ! shift 2; then MS_Help; exit 1; fi
	for s in $filesizes
	do
	MS_dd "$0" $offset $s \| eval "gzip -cd" \| tar "$arg1" - $*
	offset=`expr $offset + $s`
	done
	exit 0
	;;
	--check)
	MS_Check "$0" y
	exit 0
	;;
	--confirm)
	verbose=y
	shift
	;;
	--noexec)
	script=""
	shift
	;;
	--keep)
	keep=y
	shift
	;;
	--target)
	keep=y
	targetdir=${2:-.}
	if ! shift 2; then MS_Help; exit 1; fi
	;;
	--noprogress)
	noprogress=y
	shift
	;;
	--nox11)
	nox11=y
	shift
	;;
	--nochown)
	ownership=n
	shift
	;;
	--xwin)
	finish="echo Press Return to close this window...; read junk"
	xterm_loop=1
	shift
	;;
	--phase2)
	copy=phase2
	shift
	;;
	--)
	shift
	break ;;
	-*)
	echo Unrecognized flag : "$1" >&2
	MS_Help
	exit 1
	;;
	*)
	break ;;
	esac
	done

	if test "$quiet" = "y" -a "$verbose" = "y";then
	echo Cannot be verbose and quiet at the same time. >&2
	exit 1
	fi

	MS_PrintLicense

	case "$copy" in
	copy)
	tmpdir=$TMPROOT/makeself.$RANDOM.`date +"%y%m%d%H%M%S"`.$$
	mkdir "$tmpdir" \|\| {
	echo "Could not create temporary directory $tmpdir" >&2
	exit 1
	}
	SCRIPT_COPY="$tmpdir/makeself"
	echo "Copying to a temporary location..." >&2
	cp "$0" "$SCRIPT_COPY"
	chmod +x "$SCRIPT_COPY"
	cd "$TMPROOT"
	exec "$SCRIPT_COPY" --phase2 -- $initargs
	;;
	phase2)
	finish="$finish ; rm -rf `dirname $0`"
	;;
	esac

	if test "$nox11" = "n"; then
	if tty -s; then # Do we have a terminal?
	:
	else
	if test x"$DISPLAY" != x -a x"$xterm_loop" = x; then # No, but do we have X?
	if xset q > /dev/null 2>&1; then # Check for valid DISPLAY variable
	GUESS_XTERMS="xterm rxvt dtterm eterm Eterm kvt konsole aterm"
	for a in $GUESS_XTERMS; do
	if type $a >/dev/null 2>&1; then
	XTERM=$a
	break
	fi
	done
	chmod a+x $0 \|\| echo Please add execution rights on $0
	if test `echo "$0" \| cut -c1` = "/"; then # Spawn a terminal!
	exec $XTERM -title "$label" -e "$0" --xwin "$initargs"
	else
	exec $XTERM -title "$label" -e "./$0" --xwin "$initargs"
	fi
	fi
	fi
	fi
	fi

	if test "$targetdir" = "."; then
	tmpdir="."
	else
	if test "$keep" = y; then
	if test "$quiet" = "n";then
	echo "Creating directory $targetdir" >&2
	fi
	tmpdir="$targetdir"
	dashp="-p"
	else
	tmpdir="$TMPROOT/selfgz$$$RANDOM"
	dashp=""
	fi
	mkdir $dashp $tmpdir \|\| {
	echo 'Cannot create target directory' $tmpdir >&2
	echo 'You should try option --target dir' >&2
	eval $finish
	exit 1
	}
	fi

	location="`pwd`"
	if test x$SETUP_NOCHECK != x1; then
	MS_Check "$0"
	fi
	offset=`head -n 498 "$0" \| wc -c \| tr -d " "`

	if test x"$verbose" = xy; then
	MS_Printf "About to extract 3916 KB in $tmpdir ... Proceed ? [Y/n] "
	read yn
	if test x"$yn" = xn; then
	eval $finish; exit 1
	fi
	fi

	if test "$quiet" = "n";then
	MS_Printf "Uncompressing $label"
	fi
	res=3
	if test "$keep" = n; then
	trap 'echo Signal caught, cleaning up >&2; cd $TMPROOT; /bin/rm -rf $tmpdir; eval $finish; exit 15' 1 2 3 15
	fi

	leftspace=`MS_diskspace $tmpdir`
	if test -n "$leftspace"; then
	if test "$leftspace" -lt 3916; then
	echo
	echo "Not enough space left in "`dirname $tmpdir`" ($leftspace KB) to decompress $0 (3916 KB)" >&2
	if test "$keep" = n; then
	echo "Consider setting TMPDIR to a directory with more free space."
	fi
	eval $finish; exit 1
	fi
	fi

	for s in $filesizes
	do
	if MS_dd_Progress "$0" $offset $s \| eval "gzip -cd" \| ( cd "$tmpdir"; UnTAR x ) 1>/dev/null; then
	if test x"$ownership" = xy; then
	(PATH=/usr/xpg4/bin:$PATH; cd "$tmpdir"; chown -R `id -u` .; chgrp -R `id -g` .)
	fi
	else
	echo >&2
	echo "Unable to decompress $0" >&2
	eval $finish; exit 1
	fi
	offset=`expr $offset + $s`
	done
	if test "$quiet" = "n";then
	echo
	fi

	cd "$tmpdir"
	res=0
	if test x"$script" != x; then
	if test x"$verbose" = xy; then
	MS_Printf "OK to execute: $script $scriptargs $* ? [Y/n] "
	read yn
	if test x"$yn" = x -o x"$yn" = xy -o x"$yn" = xY; then
	eval $script $scriptargs $*; res=$?;
	fi
	else
	eval $script $scriptargs $*; res=$?
	fi
	if test $res -ne 0; then
	test x"$verbose" = xy && echo "The program '$script' returned an error code ($res)" >&2
	fi
	fi
	if test "$keep" = n; then
	cd $TMPROOT
	/bin/rm -rf $tmpdir
	fi
	eval $finish; exit $res
	��6J綺燧\曽炶夯E噒ww�wI 逸澮!妸€倀wùt)J妧历击9g遱嫖湙�}蛙遺褛箈啧y�.n�/<�.聜偪=�潲雜_�/堪牥€€ 彁///� L峥囹浪勐Cp磓urp斛7唢遻��鳢o售沦櫵塔翼�+烂/n~^~庚!�0衠[:竢[Zx賑1纞=苫果{:刭{螟xxEaZF:拷肆fT辑狜鉻祦窭頲羆搛6�0+{7綆硩厳
	腆�+搪骈骀MG�=l�急l~�钷�0NNoog絾儠嶋�摰蟠眖眖觜踬9齧糪}FFV+o槑�+锟�#椃�7�纟鯙^V瀗挝�6縙u龙�开�0N;镞鴂��鹵押璱�#�'扇瘥]沖W岱o嫍F' ＇斫~#f踣访�sp+`0N{X喁痡o沆析椬{7皐饌/拲'熳碟鮹L6^0W7o樂厯
	搪�鎛醝醔鉳汩E晴/忖紤濏_抉/_鸲珦珱鷦t0%7O豲W鲟渍E/讛霟}n�涫豿YXE/{[镞_秜s爹趼o凤弋氷_\砀竳抑頝v0N嘷灼滞邮営谄萜遮骒n�蔬輿搹嫍嬒LP標OD萀H€粟乞浊Y鼁嫕�7層�o禭6蝆6\|%房浸窙纩桝侚�=€賉兰輅繊誳/��5嬁挖�齯�緋q記挲�+黭狍瘕孆/(((�艆N侣邮^
	胱m韅崾纠掠�鰇q线齏H@圜�颊嫃�耸驼*纡吷e例飤�熜O弫犞f唨�5缶�4I悦痜瑡��;idb�7TF�冉Xo鳫-^髫E褚癄F�!"1遀C,賭I3)y�'铻k�%躍U�kc_淓 fB堠p┭: �4仜,雸�5_Wx噭
	�-\)z5耠�.�:jKa~)熶'Wv`轜圄^晪�'洫:蚙偵儆�WW挊莵騝壚E€�9丟7I畨C虸>E�-7
	Q綗�>h碦�t靸塡斶8~
	拰_V1鸃(\|鸕\|崎桴壟泳◣vf

	tree build
	build
	├── lib
	│ └── udev
	│ └── rules.d
	│ └── 99-lpcscrypt.rules
	└── usr
	└── local
	└── lpcscrypt-2.1.2_57
	├── bin
	│ ├── LPCScrypt_240.bin.hdr
	│ ├── image_manager
	│ └── lpcscrypt
	├── docs
	│ ├── Debug_Probe_Firmware_Programming.pdf
	│ └── LPCScrypt_User_Guide.pdf
	├── eula
	│ ├── SoftwareContentRegister.txt
	│ ├── licenses
	│ │ ├── Apache-2.0.txt
	│ │ ├── BSD-3-clause.txt
	│ │ ├── BSD-4-clause.txt
	│ │ ├── GPLV2.txt
	│ │ ├── LGPLV2.1.txt
	│ │ └── Zlib.txt
	│ ├── lpcscrypt_eula.docx
	│ ├── lpcscrypt_eula.rtf
	│ └── lpcscrypt_eula.txt
	├── images
	│ ├── Link2_Fill_SPIFI.bin
	│ ├── Link2_Medium_SPIFI.bin
	│ ├── Link2_Small_SPIFI.bin
	│ ├── MCB1800_FillBlinky_BankA.bin
	│ ├── MCB1800_FillBlinky_BankB.bin
	│ ├── MCB1800_FillBlinky_SPIFI.bin
	│ ├── MCB1800_LargeBlinky_BankA.bin
	│ ├── MCB1800_LargeBlinky_BankB.bin
	│ ├── MCB1800_LargeBlinky_RAM.bin
	│ ├── MCB1800_LargeBlinky_SPIFI.bin
	│ ├── MCB1800_blinky_BankA.bin
	│ ├── MCB1800_blinky_BankB.bin
	│ ├── MCB1800_blinky_RAM.bin
	│ └── MCB1800_blinky_SPIFI.bin
	├── probe_firmware
	│ ├── LPCLink2
	│ │ ├── Firmware_JLink_LPC-Link2_20190404.bin
	│ │ ├── LPC432x_CMSIS_DAP_NB_V5_224.bin.hdr
	│ │ ├── LPC432x_CMSIS_DAP_NB_V5_361.bin.hdr
	│ │ ├── LPC432x_CMSIS_DAP_SER_V5_224.bin.hdr
	│ │ ├── LPC432x_CMSIS_DAP_SER_V5_361.bin.hdr
	│ │ ├── LPC432x_CMSIS_DAP_V5_224.bin.hdr
	│ │ └── LPC432x_CMSIS_DAP_V5_361.bin.hdr
	│ └── LPCXpressoV2
	│ ├── Firmware_JLink_LPCXpressoV2_20190404.bin
	│ ├── LPC432x_IAP_CMSIS_DAP_NB_V5_224.bin
	│ ├── LPC432x_IAP_CMSIS_DAP_NB_V5_361.bin
	│ ├── LPC432x_IAP_CMSIS_DAP_SER_V5_224.bin
	│ ├── LPC432x_IAP_CMSIS_DAP_SER_V5_361.bin
	│ ├── LPC432x_IAP_CMSIS_DAP_V5_224.bin
	│ └── LPC432x_IAP_CMSIS_DAP_V5_361.bin
	└── scripts
	├── 99-lpcscrypt.rules
	├── LPCScrypt_CLI
	├── aeskey
	├── boot_lpcscrypt
	├── dfu_boot
	├── encrypt_and_program
	├── encrypt_and_program.scy
	├── install_udev_rules
	├── program_CMSIS
	└── program_JLINK

	15 directories, 54 files

	# Maintainer: taotieren <admin@taotieren.com>
	# Contributor:

	pkgname="lpcscrypt-bin"
	pkgver=2.1.2
	pkgrel=1
	pkgdesc="LPCScrypt is the recommended tool for programming the latest versions of CMSIS-DAP and J-Link firmware onto boards with Link2/LPC-Link2 debug probes."
	arch=("x86_64")
	makedepends=('imagemagick')
	depends=('jlink-software-and-documentation')
	optdepends=()
	conflicts=()
	url="https://www.nxp.com/design/microcontrollers-developer-resources/lpcscrypt-v2-1-2:LPCSCRYPT"
	license=('Commercial' 'Apache-2.0' 'BSD-4-clause' 'BSD-3-clause' 'LGPLV2.1' 'GPLV2' 'Zlib')
	options=(!strip)
	_pkgver_ext=${pkgver}_57
	_pkg_file_name=${pkgname%-bin}-${_pkgver_ext}.${arch}.deb.bin
	_deb_file_name=${pkgname%-bin}-${_pkgver_ext}.${arch}.deb
	_DOWNLOADS_DIR=`xdg-user-dir DOWNLOAD`
	if [ ! -f ${PWD}/${_pkg_file_name} ]; then
	if [ -f $_DOWNLOADS_DIR/${_pkg_file_name} ]; then
	ln -sfn $_DOWNLOADS_DIR/${_pkg_file_name} ${PWD}
	else
	msg2 ""
	msg2 "The package can be downloaded here: "
	msg2 "Please remember to put a downloaded package ${_pkg_file_name} into the build directory ${PWD} or $_DOWNLOADS_DIR"
	msg2 ""
	fi
	fi

	source=("local://${_pkg_file_name}")
	sha256sums=('379c63b788a72e64571af870d760ad6b3be32e4c863d29ca58276f750e416750')
	noextract=(${_pkg_file_name})

	prepare(){
	cd "$srcdir"
	tail -n +499 ${_pkg_file_name} > ${_deb_file_name}
	mkdir -p build
	bsdtar xf ${_deb_file_name} -C build
	bsdtar xf build/${_deb_file_name} -C build
	}
	package() {
	cd "$srcdir"

	msg2 'Installing LPCScrypt'
	tar xf "build/data.tar.gz" -C "${pkgdir}/"
	mv "${pkgdir}/lib" "${pkgdir}/usr"
	msg2 'Instalation of binary file'
	install -Dm0755 /dev/stdin "${pkgdir}/usr/bin/${pkgname%-bin}" <<END
	#!/bin/sh
	/usr/local/lpcscrypt-2.1.2_57/bin/lpcscrypt "\$@"
	END

	msg2 'Instalation of license file'
	install -dm0755 "${pkgdir}/usr/share/licenses/${pkgname%-bin}/"
	cp -rv "${pkgdir}/usr/local/lpcscrypt-2.1.2_57/eula" "${pkgdir}/usr/share/licenses/${pkgname%-bin}/"
	}

	#
	# makepkg --printsrcinfo > .SRCINFO
	#

	# vim: set ts=8 sw=8 tw=0 noet:

	makepkg -sf
	==> 正在创建软件包：lpcscrypt-bin 2.1.2-1 (2021年07月04日星期日 14时04分10秒)
	==> 正在检查运行时依赖关系...
	==> 正在检查编译时依赖关系
	==> 获取源代码...
	-> 找到 lpcscrypt-2.1.2_57.x86_64.deb.bin
	==> 正在验证 source 文件，使用sha256sums...
	lpcscrypt-2.1.2_57.x86_64.deb.bin ... 通过
	==> 正在释放源码...
	==> 正在开始 prepare()...
	==> 正在删除现存的 $pkgdir/ 目录...
	==> 正在进入 fakeroot 环境...
	==> 正在开始 package()...
	-> Installing LPCScrypt
	-> Instalation of binary file
	-> Instalation of license file
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/lpcscrypt_eula.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/lpcscrypt_eula.txt'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/lpcscrypt_eula.docx' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/lpcscrypt_eula.docx'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/lpcscrypt_eula.rtf' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/lpcscrypt_eula.rtf'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/Zlib.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/Zlib.txt'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/Apache-2.0.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/Apache-2.0.txt'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/GPLV2.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/GPLV2.txt'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/BSD-3-clause.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/BSD-3-clause.txt'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/BSD-4-clause.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/BSD-4-clause.txt'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/licenses/LGPLV2.1.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/licenses/LGPLV2.1.txt'
	'/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/local/lpcscrypt-2.1.2_57/eula/SoftwareContentRegister.txt' -> '/home/taotieren/git_clone/aur/lpcscrypt-bin/pkg/lpcscrypt-bin/usr/share/licenses/lpcscrypt/eula/SoftwareContentRegister.txt'
	==> 正在清理安装...
	-> 正在删除 libtool 文件...
	-> 正在清除不打算要的文件...
	-> 正在移除静态库文件...
	-> 正在压缩 man 及 info 文档...
	==> 正在检查打包问题...
	==> 正在构建软件包"lpcscrypt-bin"...
	-> 正在生成 .PKGINFO 文件...
	-> 正在生成 .BUILDINFO 文件...
	-> 正在生成 .MTREE 文件...
	-> 正在压缩软件包...
	==> 正在离开 fakeroot 环境。
	==> 完成创建：lpcscrypt-bin 2.1.2-1 (2021年07月04日星期日 14时04分12秒)

	sudo pacman -U lpcscrypt-bin 2.1.2-1.pkg.tar.zst
	# 或
	yay -U lpcscrypt-bin 2.1.2-1.pkg.tar.zst
	正在加载软件包...
	正在解析依赖关系...
	正在查找软件包冲突...

	软件包 (1) lpcscrypt-bin-2.1.2-1

	全部安装大小： 9.34 MiB

	:: 进行安装吗？ [Y/n]
	(1/1) 正在检查密钥环里的密钥 [##########################] 100%
	(1/1) 正在检查软件包完整性 [##########################] 100%
	(1/1) 正在加载软件包文件 [##########################] 100%
	(1/1) 正在检查文件冲突 [##########################] 100%
	(1/1) 正在检查可用存储空间 [##########################] 100%
	:: 正在处理软件包的变化...
	(1/1) 正在安装 lpcscrypt-bin [##########################] 100%
	:: 正在运行事务后钩子函数...
	(1/3) Reloading device manager configuration...
	(2/3) Arming ConditionNeedsUpdate...
	(3/3) Refreshing PackageKit...

	lpcscrypt
	lpcscrypt: NXP LPC Scripting tool. v2.1.2 (Build 44) (Nov 25 2020 13:01:49)
	usage: lpcscrypt [-d serial_port] [-e dnqst] [-g usec] [-hp] [-v var=value]
	[-s script]\|[-t]\|[[-x] command]
	where:
	-h display this help message
	-d serial_port use 'serial_port' (device) as target
	use ? to list available ports
	-s script read script from file
	-t read script from terminal (stdin)
	-x command execute 'command' only
	the -s, -t and -x options and/or immediate commands
	are mutually exclusive

	-v name=value assign variable 'name' the value 'value'
	Use [name] to reference the variable in the script
	Simple text replacement is performed on each script line
	-p pause before each script command
	-e denqst set command echo options:
	q - quiet - echo nothing [default]
	d - debug - echo additional debug information
	n - noisy - echo everything
	s - script - echo script commands
	t - target - echo target commands
	b - buffer - dump raw target buffer
	e - exit - display message on exit

	Supported high-level commands (implemented by this tool) are:
	program program [+c\|+wN] (<file>\|<fill_value>) <baseAddress>
	[<fill_length>].
	where: +c==calculate checksum
	+wN==width of fill_value, where N is 1, 2 or 4
	program file or value into flash at baseAddress
	verify verify [+c\|+i\|+wN] (<file>\|<fill_value>) <baseAddress>
	[<fill_length>].
	where: +c==calculate checksum, +i==ignore checksum
	+wN==width of fill_value, where N is 1, 2 or 4
	verify that flash contents matches the file or value
	erase erase <baseAddress>
	erase flash contents
	blankCheck blankCheck <baseAddress>
	blankcheck
	setBoot setBoot [BankA\|BankB\|0\|1]
	set the active boot flash bank
	setVidPid setVidPid <vid> <pid>
	program the OTP VID and PID
	echo echo <parameters>*
	echo all parameters to the output stream
	delay delay <microseconds>
	delay for number of microseconds
	pause pause [on\|off] \| message
	if on or off, switch autoPause on,
	else display message and wait for <ENTER>.
	(Not possible if script is from stdin)
	timer timer <start\|stop\|print>
	start/stop a timer
	var var name=value
	create a local variable
	<other> Any command supported by the target
	Multiple serial ports found:
	/dev/ttyACM1
	/dev/ttyUSB0
	/dev/ttyACM0

	git add PKGBUILD
	git add .SRCINFO
	cat > .gitignore << EOF
	*
	.
	EOF
	git add .gitignore -f
	git commit -am "Update lpcscrypt-bin"
	git push

饕餮人

Lifetime Learning！

Arch Linux/其他 Linux 下给 Link2/LPC-Link2 调试器刷 CMSIS-DAP 和 J-Link 固件

文章目录

NXP 提供的 LPCScrypt 工具

我 Arch 用户或其他 Linux 发行版用户想使用怎么办？

1. 注册 NXP 官网下载相应的 Linux 版本文件

2. 用文本编辑器打开看了下里面的内容

3. 开始 lpcscrypt-2.1.2_57.x86_64.deb.bin 解密

4. 解压 deb 包

5. 解压 data.tar.gz

6. 这下就能进行 AUR 打包处理了

7. 编译 PKGBUILD 并安装验证

8. 上传到 AUR 仓库

公告

搜索

常用链接

最新随笔

积分与排名

随笔分类 (2)

随笔档案 (19)

文章分类 (3)

文章档案 (1)

相册 (1)

阅读排行榜

4. 解压 `deb` 包

5. 解压 `data.tar.gz`

7. 编译 `PKGBUILD` 并安装验证