Haproxy+Keepalived高可用配置

基本实验

参考文档

博文地址

环境拓扑

下面使我们要实现的负载均衡集群图示

主节点地址： 92.0.0.11
从节点地址： 92.0.0.12
共享虚拟地址：92.0.0.8

下面是负载均衡集群可能出现的两种场景（当主节点故障时，将从图1切换到图2）

Application服务可以部署到其他主机节点上，这边实验为了方便就部署到同一台上

网络拓扑

br-mgmt：内网网桥（92.0.0.0/24）、br-ex:外网网桥(192.168.200.0/24)

环境搭建

安装软件

### 主/从节点都需安装
#  yum install haproxy keepalived nginx -y
# systemctl start nginx
# systemctl enable nginx

HAProxy需要绑定非本机网络地址，所以需要修改

### 主/从节点都需修改
# vim /etc/sysctl.conf
net.ipv4.ip_nonlocal_bind=1
### 让配置生效
# sysctl -p

编辑keepalived配置文件

# vim /etc/keepalived/keepalived.conf

主节点配置文件内容如下

# Script used to check if HAProxy is running
vrrp_script check_haproxy {
    script "killall -0 haproxy"
    interval 2
    weight 2
}
# Virtual interface
# The priority specifies the order in which the assigned interface to take over in a failover
vrrp_instance VI_01 {
    state MASTER
    interface ens3
    virtual_router_id 51
    priority 101
    # The virtual ip address shared between the two loadbalancers
    virtual_ipaddress {
        92.0.0.8
    }
    track_script {
        check_haproxy
    }
}

从节点配置文件内容如下

# Script used to check if HAProxy is running
vrrp_script check_haproxy {
    script "killall -0 haproxy"
    interval 2
    weight 2
}
# Virtual interface
# The priority specifies the order in which the assigned interface to take over in a failover
vrrp_instance VI_01 {
    state BACKUP
    interface ens3
    virtual_router_id 51
    priority 80
    # The virtual ip address shared between the two loadbalancers
    virtual_ipaddress {
        92.0.0.8
    }
    track_script {
        check_haproxy
    }
}

启动keepalived服务

# systemctl start keepalived
# systemctl enable keepalived

编辑haproxy配置文件

# vim /etc/haproxy/haproxy.cfg
global               #全局设置
    log 127.0.0.1   local0   #日志输出配置，所有日志都记录在本机，通过local0输出
    maxconn 4096             #最大连接数
    group haproxy            #用户组
    daemon                   #后台运行haproxy
    nbproc 1                 #启动1个haproxy实例
    pidfile /usr/local/haproxy/haproxy.pid  #将所有进程PID写入pid文件

defaults             #默认设置
    #log    global
    log     127.0.0.1       local3      #日志文件的输出定向

    #默认的模式:tcp|http|health
    mode   http         #所处理的类别,默认采用http模式

    option  httplog      #日志类别,采用http日志格式`
    option  dontlognull
    option  forwardfor   #将客户端真实ip加到HTTP Header中供后端服务器读取
    option  httpclose    #每次请求完毕后主动关闭http通道,haproxy不支持keep-alive,只>能模拟这种模式的实现
    retries 3            #3次连接失败就认为服务器不可用，主要通过后面的check检查
    option  redispatch   #当serverid对应的服务器挂掉后，强制定向到其他健康服务器
    option  abortonclose #当服务器负载很高时，自动结束掉当前队列中处理比较久的链接
    maxconn 2000         #默认最大连接数

    timeout connect 5000  #连接超时时间
    timeout client  50000 #客户端连接超时时间
    timeout server  50000 #服务器端连接超时时间

listen am_cluster 92.0.0.8:8080
    server  s1 92.0.0.11:80 check
    server  s2 92.0.0.12:80 check

启动haproxy服务

# systemctl start haproxy
# systemctl enable haproxy

查看节点网络

### Master节点
# ip addr show ens3
2: ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 52:54:00:21:07:87 brd ff:ff:ff:ff:ff:ff
    inet 92.0.0.11/24 brd 92.0.0.255 scope global ens3
       valid_lft forever preferred_lft forever
    inet 92.0.0.8/32 scope global ens3
       valid_lft forever preferred_lft forever
    inet6 fe80::5054:ff:fe21:787/64 scope link
       valid_lft forever preferred_lft forever

### Backup节点
# ip addr show ens3
2: ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 52:54:00:64:ca:a7 brd ff:ff:ff:ff:ff:ff
    inet 92.0.0.12/24 brd 92.0.0.255 scope global ens3
       valid_lft forever preferred_lft forever
    inet6 fe80::5054:ff:fe64:caa7/64 scope link
       valid_lft forever preferred_lft forever

环境测试

正常访问

关闭Master节点的Keepalived，并刷新页面

### Master节点
# systemctl stop keepalived
# ip addr show ens3
2: ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 52:54:00:21:07:87 brd ff:ff:ff:ff:ff:ff
    inet 92.0.0.11/24 brd 92.0.0.255 scope global ens3
       valid_lft forever preferred_lft forever
    inet6 fe80::5054:ff:fe21:787/64 scope link
       valid_lft forever preferred_lft forever

### Backup节点
# ip addr show ens3
2: ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 52:54:00:64:ca:a7 brd ff:ff:ff:ff:ff:ff
    inet 92.0.0.12/24 brd 92.0.0.255 scope global ens3
       valid_lft forever preferred_lft forever
    inet 92.0.0.8/32 scope global ens3
       valid_lft forever preferred_lft forever
    inet6 fe80::5054:ff:fe64:caa7/64 scope link
       valid_lft forever preferred_lft forever

关闭Backup节点的Haproxy，并刷新页面

### Backup节点
# systemctl stop haproxy

恢复Master节点的keepalived，并刷新页面

### Master节点
# systemctl start keepalived
# ip addr show ens3
2: ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 52:54:00:21:07:87 brd ff:ff:ff:ff:ff:ff
    inet 92.0.0.11/24 brd 92.0.0.255 scope global ens3
       valid_lft forever preferred_lft forever
    inet 92.0.0.8/32 scope global ens3
       valid_lft forever preferred_lft forever
    inet6 fe80::5054:ff:fe21:787/64 scope link
       valid_lft forever preferred_lft forever

### Backup节点
# ip addr show ens3
2: ens3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 52:54:00:64:ca:a7 brd ff:ff:ff:ff:ff:ff
    inet 92.0.0.12/24 brd 92.0.0.255 scope global ens3
       valid_lft forever preferred_lft forever
    inet6 fe80::5054:ff:fe64:caa7/64 scope link
       valid_lft forever preferred_lft forever

总结

keepalived在Master节点故障时，VIP会自动迁移到Slave节点，并在Master节点恢复后自动迁回（VIP抢占模式）

keepalived和haproxy只有在同一台节点才能正常工作，即Master节点的keepalived挂了，Slave节点的haproxy节点挂了，是无法正常工作的，原因未知~

Kolla实验

修改配置文件

### keepalived和haproxy都要安装到所有controller节点（准备3台host作为controller节点）
# vim multinode
[haproxy:children]
controller

# vim /usr/share/kolla-ansible/ansible/roles/haproxy/templates/keepalived.conf.j2
vrrp_script check_alive {
    script "/check_alive.sh"
    interval 2
    fall 2
    rise 10
}

vrrp_instance kolla_internal_vip_{{ keepalived_virtual_router_id }} {
{% if inventory_hostname == groups['controller'][0] %}
    state MASTER
{% else %}
    state BACKUP
{% endif %}
    nopreempt
    interface {{ api_interface }}
    virtual_router_id {{ keepalived_virtual_router_id }}
{% if inventory_hostname == groups['controller'][0] %}
    priority 100
{% else %}
    priority {{ groups['haproxy'].index(inventory_hostname) }}
{% endif %}
    advert_int 1
    virtual_ipaddress {
        {{ kolla_internal_vip_address }} dev {{  api_interface }}
{% if haproxy_enable_external_vip | bool %}
        {{ kolla_external_vip_address }} dev {{ kolla_external_vip_interface }}
{% endif %}
    }
{% if haproxy_enable_external_vip | bool and api_interface != kolla_external_vip_interface %}
    track_interface {
        {{ kolla_external_vip_interface }}
    }
{% endif %}
    authentication {
        auth_type PASS
        auth_pass {{ keepalived_password }}
    }
    track_script {
        check_alive
    }
}

### 部署OpenStack
# kolla-ansible -i multinode deploy

测试HA

直接关闭一台非network节点的controller不会影响OpenStack功能使用

posted @ 2017-10-14 11:50 银魔术师阅读(1064) 评论(0) 编辑收藏举报

刷新页面返回顶部

银魔术师