阿正的网易云音乐 - 创建于 2017

一个大学生的学习心得，与君共勉。

小智插座3.0成功

先上图   等考试完了，我再详细记录小可爱的制作过程。

 

 

  1 #include <Gizwits.h>
  2 #include <Wire.h>
  3 #include <SoftwareSerial.h>
  4 SoftwareSerial mySerial(A2, A3); // A2 -> RX, A3 -> TX
  5 Gizwits myGizwits;
  6 #define   KEY1              6
  7 #define   KEY2              7
  8 #define   KEY1_SHORT_PRESS  1
  9 #define   KEY1_LONG_PRESS   2
 10 #define   KEY2_SHORT_PRESS  4
 11 #define   KEY2_LONG_PRESS   8
 12 #define   NO_KEY            0
 13 #define   KEY_LONG_TIMER    3
 14 int flag =0;
 15 unsigned long Last_KeyTime = 0;
 16 unsigned long gokit_time_s(void)
 17 {
 18   return millis() / 1000;
 19 }
 20 char gokit_key1down(void)
 21 {
 22   unsigned long keep_time = 0;
 23   if (digitalRead(KEY1) == LOW)
 24   {
 25     delay(100);
 26     if (digitalRead(KEY1) == LOW)
 27     {
 28       keep_time = gokit_time_s();
 29       while (digitalRead(KEY1) == LOW)
 30       {
 31         if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)
 32         {
 33           Last_KeyTime = gokit_time_s();
 34           return KEY1_LONG_PRESS;
 35         }
 36       } //until open the key
 37       if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)
 38       {
 39         return KEY1_SHORT_PRESS;
 40       }
 41       return 0;
 42     }
 43     return 0;
 44   }
 45   return 0;
 46 }
 47 char gokit_key2down(void)
 48 {
 49   int unsigned long keep_time = 0;
 50   if (digitalRead(KEY2) == LOW)
 51   {
 52     delay(100);
 53     if (digitalRead(KEY2) == LOW)
 54     {
 55       keep_time = gokit_time_s();
 56       while (digitalRead(KEY2) == LOW) //until open the key
 57       {
 58         if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)
 59         {
 60           Last_KeyTime = gokit_time_s();
 61           return KEY2_LONG_PRESS;
 62         }
 63       }
 64       if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)
 65       {
 66         return KEY2_SHORT_PRESS;
 67       }
 68       return 0;
 69     }
 70     return 0;
 71   }
 72   return 0;
 73 }
 74 char gokit_keydown(void)
 75 {
 76   char ret = 0;
 77   ret |= gokit_key2down();
 78   ret |= gokit_key1down();
 79   return ret;
 80 }
 81 void KEY_Handle(void)
 82 {
 83   switch (gokit_keydown())
 84   {
 85     case KEY1_SHORT_PRESS:
 86       myGizwits.setBindMode(WIFI_PRODUCTION_TEST);
 87       break;
 88     case KEY1_LONG_PRESS:
 89       myGizwits.setBindMode(WIFI_RESET_MODE);
 90       break;
 91     case KEY2_SHORT_PRESS:
 92       myGizwits.setBindMode(WIFI_SOFTAP_MODE);
 93       break;
 94     case KEY2_LONG_PRESS:
 95       myGizwits.setBindMode(WIFI_AIRLINK_MODE);
 96     digitalWrite(5,HIGH);
 97     digitalWrite(8,HIGH);
 98     delay(1000);
 99    digitalWrite(8,LOW);
100    digitalWrite(5,LOW);
101       break;
102     default:
103       break;
104   }
105 }
106 void wifiStatusHandle()
107 {
108   if(myGizwits.wifiHasBeenSet(WIFI_SOFTAP))
109   {
110   }  
111   if(myGizwits.wifiHasBeenSet(WIFI_AIRLINK))
112   {
113   } 
114 }
115 void setup() {
116   mySerial.begin(115200);
117    pinMode(KEY1, INPUT_PULLUP);
118   pinMode(KEY2, INPUT_PULLUP);
119  pinMode(5,OUTPUT);//指示灯
120   pinMode(8,OUTPUT);//beeWIFI_AIRLINK成功报警提示
121   pinMode(9,OUTPUT);//作业执行
122   digitalWrite(5,LOW);
123   digitalWrite(8,LOW);
124   digitalWrite(9,HIGH);
125   myGizwits.begin();
126 }
127 void loop() {  
128    KEY_Handle();//key handle , network configure网络配置
129   wifiStatusHandle();//WIFI Status Handle无线网络状态处理   
130   unsigned long varW_back = 0;//Add Sensor Data Collection
131   myGizwits.write(VALUE_back, varW_back);
132 //////////////////////////////////////////////////////////////////////////////////
133   bool varR_on = 0;
134   if(myGizwits.hasBeenSet(EVENT_on))
135   {
136     myGizwits.read(EVENT_on,&varR_on);//Address for storing data
137     if(varR_on==1)
138     {
139       digitalWrite(9,LOW);
140       }
141      else
142      digitalWrite(9,HIGH);
143   }
144   bool varR_off = 0;
145   if(myGizwits.hasBeenSet(EVENT_off))
146   {
147     myGizwits.read(EVENT_off,&varR_off);//Address for storing data
148   }
149   unsigned long varR_time = 0;
150   if(myGizwits.hasBeenSet(EVENT_time))
151   {
152     myGizwits.read(EVENT_time,&varR_time);//Address for storing data
153   }
154   myGizwits.process();
155 }

外观美到炸，总体很棒！很满意哦!

 

posted @ 2017-12-23 13:51  阿♛正  阅读(384)  评论(0)  编辑  收藏  举报