基于esp8266的智能台灯DIY

研究esp8266已经很久了，特制作了一个智能灯，

代码如下，总结几点

一、关于arduino pro mini 的烧写方法

一定要在编译成功之后的下载提示出现的瞬间，单击复位按钮。才可进入烧写

二、esp8266APP界面图标功能串联混乱的解决方法，即，重新加载 机智云库文件即可。

#include <Gizwits.h>
#include <Wire.h>
#include <SoftwareSerial.h>
SoftwareSerial mySerial(A2, A3); // A2 -> RX, A3 -> TX
Gizwits myGizwits;
#define   KEY1              6
#define   KEY2              7
#define   KEY1_SHORT_PRESS  1
#define   KEY1_LONG_PRESS   2
#define   KEY2_SHORT_PRESS  4
#define   KEY2_LONG_PRESS   8
#define   NO_KEY            0
#define   KEY_LONG_TIMER    3
int flag =0;
unsigned long Last_KeyTime = 0;
unsigned long gokit_time_s(void)
{
  return millis() / 1000;
}
char gokit_key1down(void)
{
  unsigned long keep_time = 0;
  if (digitalRead(KEY1) == LOW)
  {
    delay(100);
    if (digitalRead(KEY1) == LOW)
    {
      keep_time = gokit_time_s();
      while (digitalRead(KEY1) == LOW)
      {
        if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)
        {
          Last_KeyTime = gokit_time_s();
          return KEY1_LONG_PRESS;
        }
      } //until open the key

      if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)
      {
        return KEY1_SHORT_PRESS;
      }
      return 0;
    }
    return 0;
  }
  return 0;
}

char gokit_key2down(void)
{
  int unsigned long keep_time = 0;
  if (digitalRead(KEY2) == LOW)
  {
    delay(100);
    if (digitalRead(KEY2) == LOW)
    {
      keep_time = gokit_time_s();
      while (digitalRead(KEY2) == LOW) //until open the key
      {

        if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)
        {
          Last_KeyTime = gokit_time_s();
          return KEY2_LONG_PRESS;
        }
      }
      if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)
      {
        return KEY2_SHORT_PRESS;
      }
      return 0;
    }
    return 0;
  }
  return 0;
}
char gokit_keydown(void)
{
  char ret = 0;
  ret |= gokit_key2down();
  ret |= gokit_key1down();
  return ret;
}
void KEY_Handle(void)
{
  switch (gokit_keydown())
  {
    case KEY1_SHORT_PRESS:
      myGizwits.setBindMode(WIFI_PRODUCTION_TEST);
      break;
    case KEY1_LONG_PRESS:
      myGizwits.setBindMode(WIFI_RESET_MODE);
      break;
    case KEY2_SHORT_PRESS:
      myGizwits.setBindMode(WIFI_SOFTAP_MODE);
      break;
    case KEY2_LONG_PRESS:
      myGizwits.setBindMode(WIFI_AIRLINK_MODE);
    digitalWrite(5,HIGH);
    digitalWrite(8,HIGH);
    delay(1000);
   digitalWrite(8,LOW);
   digitalWrite(5,LOW);
      break;
    default:
      break;
  }
}
void wifiStatusHandle()
{
  if(myGizwits.wifiHasBeenSet(WIFI_SOFTAP))
  {
  }  
  if(myGizwits.wifiHasBeenSet(WIFI_AIRLINK))
  {
  } 
}

void setup() {
  // put your setup code here, to run once:

  mySerial.begin(115200);
   pinMode(KEY1, INPUT_PULLUP);
  pinMode(KEY2, INPUT_PULLUP);
  pinMode(10,INPUT);//红外探头
  pinMode(5,OUTPUT);//指示灯
  pinMode(8,OUTPUT);//beeWIFI_AIRLINK成功报警提示
  pinMode(9,OUTPUT);//test
  pinMode(11,OUTPUT);
  digitalWrite(5,LOW);
  digitalWrite(8,LOW);
  digitalWrite(9,HIGH);
  myGizwits.begin();
}
void loop() {  
   KEY_Handle();//key handle , network configure网络配置
  wifiStatusHandle();//WIFI Status Handle无线网络状态处理
  unsigned long varW_timeh ;//Add Sensor Data Collection
  unsigned long varR_T_Minutes;
  bool varR_on_off ;
  if (digitalRead(10)==LOW)
  { 
   digitalWrite(9,LOW);
    }
  if(myGizwits.hasBeenSet(EVENT_on_off))
  {
    myGizwits.read(EVENT_on_off,&varR_on_off);//Address for storing data
    if(varR_on_off==1)
    {
      digitalWrite(9,LOW);
      }
     else
     digitalWrite(9,HIGH);
  }
  if(myGizwits.hasBeenSet(EVENT_T_Minutes))
  {
    myGizwits.read(EVENT_T_Minutes,&varR_T_Minutes);//Address for storing data

    analogWrite(11,int(varR_T_Minutes));
    varW_timeh=varR_T_Minutes;
     myGizwits.write(VALUE_timeh, varW_timeh);
  }
  myGizwits.process();

}