03 AXI4总线axi-lite-master
软件版本:vitis2021.1(vivado2021.1)
操作系统:WIN10 64bit
硬件平台:适用XILINX A7/K7/Z7/ZU/KU系列FPGA
登录"米联客"FPGA社区-www.uisrc.com视频课程、答疑解惑!
2.1概述
关于AXI4总线协议的部分介绍请阅读"01AXI4总线axi-lite-slave"。
2:掌握通过VIVADO工具产生AXI-lite-master代码
3:理解AXI-lite-master中自定义寄存器的地址分配
4:掌握通过VIVADO封装AXI-lite-master图形化IP
5:通过仿真验证AXI-lite-master IP的工作是否正常。
2.2创建axi4-lite-master总线接口IP
新建完成工程后,单击菜单栏Tools->Create and Package New IP,开始创建一个AXI4-Lite接口总线IP
选择使用vivado自带的AXI总线模板创建一个AXI4-Lite接口IP
模板支持3种协议,分别是AXI4-Full ,AXI4-Lite ,AXI4-Stream
总线包括Master和Slave两种模式,这里选择Master模式
这里选择Verify Peripheral IP using AXI4 VIP 可以对AXI4-Lite快速验证
2.3程序分析
1:产生初始化信号
always @(posedge M_AXI_ACLK) begin // Initiates AXI transaction delay if (M_AXI_ARESETN == 0 ) begin init_txn_ff <= 1'b0; init_txn_ff2 <= 1'b0; end else begin init_txn_ff <= INIT_AXI_TXN; init_txn_ff2 <= init_txn_ff; end end |
2:axi-lite-master的axi_awvalid
当start_single_write有效,开始一次写传输,设置axi_awvalid有效。
always @(posedge M_AXI_ACLK) begin //Only VALID signals must be deasserted during reset per AXI spec //Consider inverting then registering active-low reset for higher fmax if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin axi_awvalid <= 1'b0; end //用户逻辑发出新地址/数据命令的信号 else begin if (start_single_write) begin axi_awvalid <= 1'b1; end //Address accepted by interconnect/slave (issue of M_AXI_AWREADY by slave) else if (M_AXI_AWREADY && axi_awvalid) begin axi_awvalid <= 1'b0; end end end |
3:axi-lite-master的axi_awaddr
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin axi_awaddr <= 0; end // Signals a new write address/ write data is // available by user logic else if (M_AXI_AWREADY && axi_awvalid) begin axi_awaddr <= axi_awaddr + 32'h00000004;
end end |
4:axi-lite-master的axi_wvalid
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin axi_wvalid <= 1'b0; end //Signal a new address/data command is available by user logic else if (start_single_write) begin axi_wvalid <= 1'b1; end //Data accepted by interconnect/slave (issue of M_AXI_WREADY by slave) else if (M_AXI_WREADY && axi_wvalid) begin axi_wvalid <= 1'b0; end end |
5:axi-lite-master的axi_wdata
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1 ) begin axi_wdata <= C_M_START_DATA_VALUE; end // Signals a new write address/ write data is // available by user logic else if (M_AXI_WREADY && axi_wvalid) begin axi_wdata <= C_M_START_DATA_VALUE + write_index; end end |
6:写次数记录write_index计数器
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin write_index <= 0; end // Signals a new write address/ write data is // available by user logic else if (start_single_write) begin write_index <= write_index + 1; end end |
7:axi-lite-master的axi_bready
当收到写通道的axi-lite-slave发回的M_AXI_BVALDI应答信号,设置axi_bready为1,BRESP返回AXI写操作是否有错误。
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin axi_bready <= 1'b0; end // accept/acknowledge bresp with axi_bready by the master // when M_AXI_BVALID is asserted by slave else if (M_AXI_BVALID && ~axi_bready) begin axi_bready <= 1'b1; end // deassert after one clock cycle else if (axi_bready) begin axi_bready <= 1'b0; end // retain the previous value else axi_bready <= axi_bready; end
//Flag write errors assign write_resp_error = (axi_bready & M_AXI_BVALID & M_AXI_BRESP[1]); |
8:axi-lite-master的axi_arvalid
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin axi_arvalid <= 1'b0; end //Signal a new read address command is available by user logic else if (start_single_read) begin axi_arvalid <= 1'b1; end //RAddress accepted by interconnect/slave (issue of M_AXI_ARREADY by slave) else if (M_AXI_ARREADY && axi_arvalid) begin axi_arvalid <= 1'b0; end // retain the previous value end |
9:axi-lite-master的axi_araddr
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin axi_awaddr <= 0; end // Signals a new write address/ write data is // available by user logic else if (M_AXI_AWREADY && axi_awvalid) begin axi_awaddr <= axi_awaddr + 32'h00000004;
end end |
10:axi-lite-master的axi_rready
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin axi_rready <= 1'b0; end // accept/acknowledge rdata/rresp with axi_rready by the master // when M_AXI_RVALID is asserted by slave else if (M_AXI_RVALID && ~axi_rready) begin axi_rready <= 1'b1; end // deassert after one clock cycle else if (axi_rready) begin axi_rready <= 1'b0; end // retain the previous value end
//Flag write errors assign read_resp_error = (axi_rready & M_AXI_RVALID & M_AXI_RRESP[1]); |
11:axi-lite-master的M_AXI_RDATA
当M_AXI_RVALID && axi_rready都有效的时候,对读取的M_AXI_RDATA数据和expected_rdata数据进行比较。
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) read_mismatch <= 1'b0;
//The read data when available (on axi_rready) is compared with the expected data else if ((M_AXI_RVALID && axi_rready) && (M_AXI_RDATA != expected_rdata)) read_mismatch <= 1'b1; else read_mismatch <= read_mismatch; end |
12:产生对比数据expected_rdata
数据expected_rdata用于和读出的M_AXI_RDATA进行对比以此验证数据的正确性。
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1 ) begin axi_wdata <= C_M_START_DATA_VALUE; end // Signals a new write address/ write data is // available by user logic else if (M_AXI_WREADY && axi_wvalid) begin axi_wdata <= C_M_START_DATA_VALUE + write_index; end end |
13:读次数记录read_index计数器
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin read_index <= 0; end // Signals a new read address is // available by user logic else if (start_single_read) begin read_index <= read_index + 1; end end |
14:axi-lite-master的状态机
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) begin expected_rdata <= C_M_START_DATA_VALUE; end // Signals a new write address/ write data is // available by user logic else if (M_AXI_RVALID && axi_rready) begin expected_rdata <= C_M_START_DATA_VALUE + read_index; end end //implement master command interface state machine always @ ( posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 1'b0) begin // reset condition // All the signals are assigned default values under reset condition mst_exec_state <= IDLE; start_single_write <= 1'b0; write_issued <= 1'b0; start_single_read <= 1'b0; read_issued <= 1'b0; compare_done <= 1'b0; ERROR <= 1'b0; end else begin // state transition case (mst_exec_state)
IDLE: // This state is responsible to initiate // AXI transaction when init_txn_pulse is asserted if ( init_txn_pulse == 1'b1 ) begin mst_exec_state <= INIT_WRITE; ERROR <= 1'b0; compare_done <= 1'b0; end else begin mst_exec_state <= IDLE; end
INIT_WRITE: // This state is responsible to issue start_single_write pulse to // initiate a write transaction. Write transactions will be // issued until last_write signal is asserted. // write controller if (writes_done) begin mst_exec_state <= INIT_READ;// end else begin mst_exec_state <= INIT_WRITE;
if (~axi_awvalid && ~axi_wvalid && ~M_AXI_BVALID && ~last_write && ~start_single_write && ~write_issued) begin start_single_write <= 1'b1; write_issued <= 1'b1; end else if (axi_bready) begin write_issued <= 1'b0; end else begin start_single_write <= 1'b0; //Negate to generate a pulse end end
INIT_READ: // This state is responsible to issue start_single_read pulse to // initiate a read transaction. Read transactions will be // issued until last_read signal is asserted. // read controller if (reads_done) begin mst_exec_state <= INIT_COMPARE; end else begin mst_exec_state <= INIT_READ;
if (~axi_arvalid && ~M_AXI_RVALID && ~last_read && ~start_single_read && ~read_issued) begin start_single_read <= 1'b1; read_issued <= 1'b1; end else if (axi_rready) begin read_issued <= 1'b0; end else begin start_single_read <= 1'b0; //Negate to generate a pulse end end
INIT_COMPARE: begin // This state is responsible to issue the state of comparison // of written data with the read data. If no error flags are set, // compare_done signal will be asseted to indicate success. ERROR <= error_reg; mst_exec_state <= IDLE; compare_done <= 1'b1; end default : begin mst_exec_state <= IDLE; end endcase end end //MASTER_EXECUTION_PROC |
15:最后一个写数据
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) last_write <= 1'b0; //The last write should be associated with a write address ready response else if ((write_index == C_M_TRANSACTIONS_NUM) && M_AXI_AWREADY) last_write <= 1'b1; else last_write <= last_write; end
//Check for last write completion. //This logic is to qualify the last write count with the final write //response. This demonstrates how to confirm that a write has been //committed.
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) writes_done <= 1'b0;
//The writes_done should be associated with a bready response else if (last_write && M_AXI_BVALID && axi_bready) writes_done <= 1'b1; else writes_done <= writes_done; end |
16:最后一个读数据
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) last_read <= 1'b0;
//The last read should be associated with a read address ready response else if ((read_index == C_M_TRANSACTIONS_NUM) && (M_AXI_ARREADY) ) last_read <= 1'b1; else last_read <= last_read; end
/* Check for last read completion. This logic is to qualify the last read count with the final read response/data. */
always @(posedge M_AXI_ACLK) begin if (M_AXI_ARESETN == 0 || init_txn_pulse == 1'b1) reads_done <= 1'b0; //The reads_done should be associated with a read ready response else if (last_read && M_AXI_RVALID && axi_rready) reads_done <= 1'b1; else reads_done <= reads_done; end |
2.4实验结果
本文来米联客(milianke),作者:米联客(milianke),转载请注明原文链接:https://www.cnblogs.com/milianke/p/17936357.html