keepalived+DR
准备四台服务器
2台LVS 2台web
1.做LVS主备,都要安装ipvsadm和keepalived
yum -y install keepalived ipvsadm
LVS的主操作:
更改keepalived的配置文件 vim /etc/keepalived/keepalived.conf
vrrp_instance VI_1 {
state MASTER \\初始状态
interface eth0 \\VIP的网卡
virtual_router_id 51
priority 100 \\优先级
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
192.168.189.181 \\VIP地址
}
}
virtual_server 192.168.189.181 80 { \\虚拟服务器
delay_loop 6
lb_algo rr \\算法
lb_kind DR \\模式
nat_mask 255.255.255.0 \\子网掩码
protocol TCP \\虚拟服务器协议
real_server 192.168.189.163 80 { \\真实服务器web1的ip地址和端口
weight 1 \\权重
TCP_CHECK { \\健康检查模块
connect_timeout 3
connect_port 80
nb_get_retry 3
delay_before_retry 3
}
}
real_server 192.168.189.164 80 { \\真实服务器web2的ip地址和端口
weight 1 \\权重
TCP_CHECK { \\健康检查模块
connect_timeout 3
connect_port 80
nb_get_retry 3
delay_before_retry 3
}
}
}
从:vrrp_instance VI_1 {
state BACKUP \\初始状态
interface eth0 \\VIP的网卡
virtual_router_id 51
priority 99 \\优先级
advert_int 1
authentication {
auth_type PASS
auth_pass 1111
}
virtual_ipaddress {
192.168.189.181 \\VIP地址
}
}
配置完毕,关闭防火墙和selinux,启动keepalived
查看VIP是否生成 ip a 出现真实ip和vip则为成功
ip a
eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:0c:29:fc:d6:23 brd ff:ff:ff:ff:ff:ff
inet 192.168.189.161/24 brd 192.168.189.255 scope global eth0
inet 192.168.189.181/32 scope global eth0
web服务配置
1.安装httpd并创建测试页面
yum -y install httpd vim /var/www/html/index.html
2.增加lo:0,并绑定vip (配置文件中添加的vip是keepalived配置文件中的vip)
3.修改arp级别
4.增加静态路由
5.关闭防火墙 开启Apache服务
全部配置完毕后,在LVS主上执行如下命令,查看LVS规则是否增加成功
# ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 192.168.189.181:80 rr
-> 192.168.189.163:80 Route 1 0 0
-> 192.168.189.164:80 Route 1 0 0
若有规则输出说明成功
################################################################
访问VIP测试效果
并且停止主的keepalived测试VIP是否飘逸之LVS的备份主机,若能成功飘逸,并且可以正常访问,说明我们实现了LVS+keepalvied集群的配置,
成功实现了LVS的高可用