OSPF 多区域配置

GNS3图标

通过配置OSPF协议使网络互通。

实验拓扑

OSPF多区域配置

如图所示连接，地址规划如下：

名称	接口	IP地址
R1	f1/0	192.168.10.1/24
R1	f0/0	192.168.20.1/24
R1	f0/1	192.168.50.2/24
R2	f0/0	192.168.20.2/24
R2	f0/1	192.168.30.1/24
R3	f0/0	192.168.30.2/24
R3	f0/1	192.168.40.1/24
R3	f1/0	192.168.60.1/24
R4	f0/0	192.168.40.2/24
R4	f0/1	192.168.50.1/24
PC1	e0	192.168.10.2/24
PC2	e0	192.168.60.2/24

配置方法

R1(config)#router ospf 1
R1(config-router)#router-id 1.1.1.1
R1(config-router)#network 192.168.20.0 0.0.0.255 area 0
R1(config-router)#network 192.168.50.0 0.0.0.255 area 0
R1(config-router)#network 192.168.10.0 0.0.0.255 area 0
R1(config-router)#ex

配置过程

配置接口 IP 地址

R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#int f0/0
R1(config-if)#ip add 192.168.20.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#ex
R1(config)#int f0/1
R1(config-if)#ip add 192.168.50.2 255.255.255.0
R1(config-if)#no sh
R1(config-if)#ex
R1(config)#int f1/0
R1(config-if)#ip add 192.168.10.1 255.255.255.0
R1(config-if)#no sh
R1(config-if)#ex
R1(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.20.1    YES manual up                    up      
FastEthernet0/1            192.168.50.2    YES manual up                    up      
FastEthernet1/0            192.168.10.1    YES manual up                    up

R2#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R2(config)#int f0/0
R2(config-if)#ip add 192.168.20.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#ex
R2(config)#int f0/1
R2(config-if)#ip add 192.168.30.1 255.255.255.0
R2(config-if)#no sh
R2(config-if)#ex
R2(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.20.2    YES manual up                    up      
FastEthernet0/1            192.168.30.1    YES manual up                    up

R3#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R3(config)#int f0/0
R3(config-if)#ip add 192.168.30.2 255.255.255.0
R3(config-if)#no sh
R3(config-if)#ex
R3(config)#int f0/1
R3(config-if)#ip add 192.168.40.1 255.255.255.0
R3(config-if)#no sh
R3(config-if)#ex
R3(config)#int f1/0
R3(config-if)#ip add 192.168.60.1 255.255.255.0
R3(config-if)#no sh
R3(config-if)#ex
R3(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.30.2    YES manual up                    up      
FastEthernet0/1            192.168.40.1    YES manual up                    up      
FastEthernet1/0            192.168.60.1    YES manual up                    up

R4#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R4(config)#int f0/0
R4(config-if)#ip add 192.168.40.2 255.255.255.0
R4(config-if)#no sh
R4(config-if)#ex
R4(config)#int f0/1
R4(config-if)#ip add 192.168.50.1 255.255.255.0
R4(config-if)#no sh
R4(config-if)#ex
R4(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.40.2    YES manual up                    up      
FastEthernet0/1            192.168.50.1    YES manual up                    up

配置 loopback IP 地址

R1(config)#int loopback 0
R1(config-if)#ip add 1.1.1.1 255.255.255.255
R1(config-if)#no sh
R1(config-if)#ex
R1(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.20.1    YES manual up                    up      
FastEthernet0/1            192.168.50.2    YES manual up                    up      
FastEthernet1/0            192.168.10.1    YES manual up                    up      
Loopback0                  1.1.1.1         YES manual up                    up      
R1(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
C       1.1.1.1 is directly connected, Loopback0
C    192.168.10.0/24 is directly connected, FastEthernet1/0
C    192.168.20.0/24 is directly connected, FastEthernet0/0
C    192.168.50.0/24 is directly connected, FastEthernet0/1

R2(config)#int loopback 0
R2(config-if)#ip add 2.2.2.2 255.255.255.255
R2(config-if)#no sh
R2(config-if)#ex
R2(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.20.2    YES manual up                    up      
FastEthernet0/1            192.168.30.1    YES manual up                    up      
Loopback0                  2.2.2.2         YES manual up                    up      
R2(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     2.0.0.0/32 is subnetted, 1 subnets
C       2.2.2.2 is directly connected, Loopback0
C    192.168.30.0/24 is directly connected, FastEthernet0/1
C    192.168.20.0/24 is directly connected, FastEthernet0/0

R3(config)#int loopback 0
R3(config-if)#ip add 3.3.3.3 255.255.255.255
R3(config-if)#no sh
R3(config-if)#ex
R3(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.30.2    YES manual up                    up      
FastEthernet0/1            192.168.40.1    YES manual up                    up      
FastEthernet1/0            192.168.60.1    YES manual up                    up      
Loopback0                  3.3.3.3         YES manual up                    up      
R3(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     3.0.0.0/32 is subnetted, 1 subnets
C       3.3.3.3 is directly connected, Loopback0
C    192.168.30.0/24 is directly connected, FastEthernet0/0
C    192.168.60.0/24 is directly connected, FastEthernet1/0
C    192.168.40.0/24 is directly connected, FastEthernet0/1

R4(config)#int loopback 0
R4(config-if)#ip add 4.4.4.4 255.255.255.255
R4(config-if)#no sh
R4(config-if)#ex
R4(config)#do show ip int b
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            192.168.40.2    YES manual up                    up      
FastEthernet0/1            192.168.50.1    YES manual up                    up      
Loopback0                  4.4.4.4         YES manual up                    up      
R4(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     4.0.0.0/32 is subnetted, 1 subnets
C       4.4.4.4 is directly connected, Loopback0
C    192.168.40.0/24 is directly connected, FastEthernet0/0
C    192.168.50.0/24 is directly connected, FastEthernet0/1

配置 OSPF

R1(config)#router ospf 1
R1(config-router)#router-id 1.1.1.1
R1(config-router)#network 192.168.20.0 0.0.0.255 area 0
R1(config-router)#network 192.168.50.0 0.0.0.255 area 0
R1(config-router)#network 192.168.10.0 0.0.0.255 area 0
R1(config-router)#ex

R2(config)#router ospf 1
R2(config-router)#router-id 2.2.2.2
R2(config-router)#network 192.168.20.0 0.0.0.255 area 0
R2(config-router)#network 192.168.30.0 0.0.0.255 area 1
R2(config-router)#ex

R3(config)#router ospf 1
R3(config-router)#router-id 3.3.3.3
R3(config-router)#network 192.168.30.0 0.0.0.255 area 1
R3(config-router)#network 192.168.40.0 0.0.0.255 area 1
R3(config-router)#network 192.168.60.0 0.0.0.255 area 1
R3(config-router)#ex

R4(config)#router ospf 1
R4(config-router)#router-id 4.4.4.4
R4(config-router)#network 192.168.40.0 0.0.0.255 area 1
R4(config-router)#network 192.168.50.0 0.0.0.255 area 0
R4(config-router)#ex

查看路由表

R1(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     1.0.0.0/32 is subnetted, 1 subnets
C       1.1.1.1 is directly connected, Loopback0
O IA 192.168.30.0/24 [110/20] via 192.168.20.2, 00:15:07, FastEthernet0/0
O IA 192.168.60.0/24 [110/21] via 192.168.50.1, 00:00:41, FastEthernet0/1
                     [110/21] via 192.168.20.2, 00:00:41, FastEthernet0/0
C    192.168.10.0/24 is directly connected, FastEthernet1/0
O IA 192.168.40.0/24 [110/20] via 192.168.50.1, 00:05:52, FastEthernet0/1
C    192.168.20.0/24 is directly connected, FastEthernet0/0
C    192.168.50.0/24 is directly connected, FastEthernet0/1

R2(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     2.0.0.0/32 is subnetted, 1 subnets
C       2.2.2.2 is directly connected, Loopback0
C    192.168.30.0/24 is directly connected, FastEthernet0/1
O    192.168.60.0/24 [110/11] via 192.168.30.2, 00:01:09, FastEthernet0/1
O    192.168.10.0/24 [110/11] via 192.168.20.1, 00:02:26, FastEthernet0/0
O    192.168.40.0/24 [110/20] via 192.168.30.2, 00:10:33, FastEthernet0/1
C    192.168.20.0/24 is directly connected, FastEthernet0/0
O    192.168.50.0/24 [110/20] via 192.168.20.1, 00:06:15, FastEthernet0/0

R3(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

     3.0.0.0/32 is subnetted, 1 subnets
C       3.3.3.3 is directly connected, Loopback0
C    192.168.30.0/24 is directly connected, FastEthernet0/0
C    192.168.60.0/24 is directly connected, FastEthernet1/0
O IA 192.168.10.0/24 [110/21] via 192.168.40.2, 00:02:35, FastEthernet0/1
                     [110/21] via 192.168.30.1, 00:02:35, FastEthernet0/0
C    192.168.40.0/24 is directly connected, FastEthernet0/1
O IA 192.168.20.0/24 [110/20] via 192.168.30.1, 00:10:38, FastEthernet0/0
O IA 192.168.50.0/24 [110/20] via 192.168.40.2, 00:06:34, FastEthernet0/1

R4(config)#do show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area 
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

O    192.168.30.0/24 [110/20] via 192.168.40.1, 00:06:51, FastEthernet0/0
O    192.168.60.0/24 [110/11] via 192.168.40.1, 00:01:27, FastEthernet0/0
     4.0.0.0/32 is subnetted, 1 subnets
C       4.4.4.4 is directly connected, Loopback0
O    192.168.10.0/24 [110/11] via 192.168.50.2, 00:02:44, FastEthernet0/1
C    192.168.40.0/24 is directly connected, FastEthernet0/0
O    192.168.20.0/24 [110/20] via 192.168.50.2, 00:06:36, FastEthernet0/1
C    192.168.50.0/24 is directly connected, FastEthernet0/1

验证结果

配置VPC的IP地址

PC1> ip 192.168.10.2 192.168.10.1
Checking for duplicate address...
PC1 : 192.168.10.2 255.255.255.0 gateway 192.168.10.1

PC2> ip 192.168.60.2 192.168.60.1
Checking for duplicate address...
PC1 : 192.168.60.2 255.255.255.0 gateway 192.168.60.1

测试可以相互ping通

PC1> ping 192.168.60.2
192.168.60.2 icmp_seq=1 timeout
84 bytes from 192.168.60.2 icmp_seq=2 ttl=61 time=59.831 ms
84 bytes from 192.168.60.2 icmp_seq=3 ttl=61 time=63.507 ms
84 bytes from 192.168.60.2 icmp_seq=4 ttl=61 time=57.735 ms
84 bytes from 192.168.60.2 icmp_seq=5 ttl=61 time=64.449 ms

PC2> ping 192.168.10.2
84 bytes from 192.168.10.2 icmp_seq=1 ttl=61 time=58.141 ms
84 bytes from 192.168.10.2 icmp_seq=2 ttl=61 time=55.996 ms
84 bytes from 192.168.10.2 icmp_seq=3 ttl=61 time=64.000 ms
84 bytes from 192.168.10.2 icmp_seq=4 ttl=61 time=56.732 ms
84 bytes from 192.168.10.2 icmp_seq=5 ttl=61 time=65.020 ms

posted @ 2019-10-07 23:41 LinSenGeGe 阅读(455) 评论(0) 编辑收藏举报

刷新页面返回顶部

Loading

LinSenGeGe

OSPF 多区域配置

实验拓扑

配置方法

配置过程

配置接口 IP 地址

配置 loopback IP 地址

配置 OSPF

查看路由表

验证结果

公告