NodeMCU文档中文翻译 2 首页

一、译文 

1、NodeMCU文档 

NodeMCU是基于ESP8266 WiFi SOC(来自Espressif)的eLua固件，固件基于espressif non-os SDK并且使用基于spiffs的文件系统。SDK代码库由98.1%的C语言代码和少量的Lua嵌入式代码组成。

NodeMCU固件是与流行的NodeMCU dev kits相配套的项目，现成的开源开发板esp8266-12e芯片。

2、编程模式

NodeMCU的编程模式很像Node.js,只是用的是Lua语言。它是异步和事件驱动的。因此，很多函数又有回调函数作其参数。下面的示例会让你感受到NodeMCU编程就像学习短代码片段。更多的例程可以查看GitHub仓库中的/lua_examples文件夹。

-- 连接到WIFI访问热点
wifi.setmode(wifi.STATION)
wifi.sta.config("SSID", "password")

-- 注册WIFI回调事件
wifi.sta.eventMonReg(wifi.STA_CONNECTING, function(previous_state)
    if(previous_state==wifi.STA_GOTIP) then 
        print("丢失连接.尝试重新连接...")
    else
        print("连接中")
    end
end)

-- 像Arduino一样操作硬件
pin = 1
gpio.mode(pin, gpio.OUTPUT)
gpio.write(pin, gpio.HIGH)
print(gpio.read(pin))

3、准备开始

3.1、构建你所需要模块的固件
3.2、烧写固件到芯片

3.3、上传代码到芯片空间
【转载请注明出处:http://blog.csdn.net/leytton/article/details/51722299】

二、原文

摘自https://nodemcu.readthedocs.io/en/master/en/ 

NodeMCU Documentation

NodeMCU is an eLua based firmware for the ESP8266 WiFi SOC from Espressif. The firmware is based on the Espressif NON-OS SDK and uses a file system based on spiffs. The code repository consists of 98.1% C-code that glues the thin Lua veneer to the SDK.

The NodeMCU firmware is a companion project to the popular NodeMCU dev kits, ready-made open source development boards with ESP8266-12E chips.

Programming Model

The NodeMCU programming model is similar to that of Node.js, only in Lua. It is asynchronous and event-driven. Many functions, therefore, have parameters for callback functions. To give you an idea what a NodeMCU program looks like study the short snippets below. For more extensive examples have a look at the /lua_examples folder in the repository on GitHub.

-- a simple HTTP server
srv = net.createServer(net.TCP)
srv:listen(80, function(conn)
    conn:on("receive", function(conn, payload)
        print(payload)
        conn:send("<h1> Hello, NodeMCU.</h1>")
    end)
    conn:on("sent", function(conn) conn:close() end)
end)

-- connect to WiFi access point
wifi.setmode(wifi.STATION)
wifi.sta.config("SSID", "password")

-- register event callbacks for WiFi events
wifi.sta.eventMonReg(wifi.STA_CONNECTING, function(previous_state)
    if(previous_state==wifi.STA_GOTIP) then 
        print("Station lost connection with access point. Attempting to reconnect...")
    else
        print("STATION_CONNECTING")
    end
end)

-- manipulate hardware like with Arduino
pin = 1
gpio.mode(pin, gpio.OUTPUT)
gpio.write(pin, gpio.HIGH)
print(gpio.read(pin))

Getting Started

1. Build the firmeware with the modules you need.
2. Flash the firmware to the chip.
3. Upload code to the firmware.