【Network】Calico, Flannel, Weave and Docker Overlay Network 各种网络模型之间的区别

From the previous posts, I have analysed 4 different Docker multi-host network solutions - Calico, Flannel, Weave and Docker Overlay Network. You can see more details on how to install, config and tune features of them from previous posts:

This post provides a battlefiled for these 4 Docker multi-host network solutions, including features and performances.

If you want to see the results directly, directly jump to the Conclusion chapter.

Docker Multi-host Networking Introduction

Docker kicked off with a simple single-host networking from the very beginning. Unfortunately, this prevents Docker clusters from scale out to multiple hosts. A number of projects put their focus on this problem such as Calico, Flannel and Weave, and also since Nov. 2015, Docker support the Multi-host Overlay Networking itself.

What these projects have in common is trying to control the container’s networking configurations, thus to capture and inject network packets. Consequently, every containers located on different hosts can get IPs in the same subnet and communicate with each other as if they are connected to the same L2 switch. In this way, containers could spread out on multiple hosts, even on multiple data centers.

While there are also a lot of differences between them from technical models, network topology and features. This post will mainly focus on the differences between Calico, Flannel, Weave and Docker Overlay Network, and you could choose the right solution which fits best to your requirements.

Battlefield Overview

According the features these Big Four support, I will compare them in the following aspects:

  • Network Model - What kind of network model are used to support multi-host network.
  • Application Isolation - Support what level and kind of application isolation of containers.
  • Name Service - DNS lookup with simple hostname or DNS rules.
  • Distributed Storage Requirements - Whether an external distributed storage is required, e.g. etcd or consul.
  • Encryption Channel - Whether data and infomation tranvers can put in an encryption channel.
  • Partially Connected Network Support - Whether the system can run on a partially connected host network.
  • Seperate vNIC for Container - Whether a seperate NIC is generated for container.
  • IP Overlap Support - Whether the same IP can be allocated to different containers.
  • Container Subnet Restriction - Whether container’s subnet should not be the same as host’s.
  • Protocol Support - What kind of Layer-3 or Layer-4 protocols are supported.

Now let’s see more details of these aspects on Calico, Flannel, Weave and Docker Overlay Network.

Network Model

Multi-host networking means aggregating containers on different hosts to a same virtual network, and also these networking providers (Calico, etc.) are organized as a clustering network, too. The cluster organizations are called network model in this post. Technically, these four solutions uses different network model to organize their own network topology.

Calico implements a pure Layer 3 approach to achieve a simpler, higher scaling, better performance and more efficient multi-host networking. So Calico can not be treated as an overlay network. The pure Layer 3 approach avoids the packet encapsulation associated with the Layer 2 solution which simplifies diagnostics, reduces transport overhead and improves performance. Calico also implements BGP protocl for routing combined with a pure IP network, thus allows Internet scaling for virtual networks.

Flannel has two different network model to choose. One is called UDP backend, which is a simple IP-over-IP solutions which uses a TUN device to encapsulate every IP fragment in a UDP packet, thus forming an overlay network; the other is a VxLAN backend, which is same as Docker Overlay Network. I have run a simple test for these two models, VxLAN is much more faster than UDP backend. The reason, I suggest, is that VxLAN is well supported by Linux Kernel, while UDP backend implements a pure software-layer encapsulation. Flannel requires a Etcd cluster to store the network configuration, allocate subnets and auxiliary data (such as host’s IP). And the packet routing also requires the cooperation of Etcd cluster. Besides, Flannel runs a seperate process flanneldon host environment to support packet switching. Apart from Docker, flannel can also used for traditional VMs.

Weave also has two different connection modes. One is called sleeve, which implements a UDP channel to tranverse IP packets from containers. The main differences between Weave sleeve mode and Flannel UDP backend mode is that, Weave will merge multiple container’s packet to one packet and transfer via UDP channel, so technically Weave sleeve mode will be a bit faster than Flannel UDP backend mode in most cases. The other connection mode of Weave is called fastdp mode, which also implements a VxLAN solutions. Though there’s no official documents clarifying the VxLAN usage, we still can found the usage of VxLAN from Weave codes. Weave runs a Docker container performing the same role as flanneld.

Docker Overlay Network implements a VxLAN-based solution with the help of libnetwork and libkv, and, of course, is integrated into Docker succesfully without any seperate process or containers.

So a brief conclusion of network model is in the following table:

 CalicoFlannelWeaveDocker Overlay Network
Network Model Pure Layer-3 Solution VxLAN or UDP Channel VxLAN or UDP Channel VxLAN

Application Isolation

Since containers are connected to each other, we need a method to put containers into different groups and isolate containers in different group.

FlannelWeave and Docker Overlay Network uses the same application isolation schema - the traditional CIDR isolation. The traditional CIDR isolation uses netmask to identify different subnet, and machines in different subnet cannot talk to each other. For example, w1/w2/w3 has IP 192.168.0.2/24 192.168.0.3/24 and 192.168.1.2/24 seperately. w1 and w2 can talk to each other since they are in the same subnet 192.168.0.0/24, but w3 cannot talk to w1 and w2.

Calico implements another type of application isolation schema - profile. You can create a batch of profiles and append containers with Calico network into different profiles. Only containers in the same profile could talk to each other. Containers in differen profile cannot access to each other even though they are in the same CIDR subnet.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Application Isolation Profile Schema CIDR Schema CIDR Schema CIDR Schema

Protocol Support

Since Calico is a pure Layer-3 solution, not all Layer-3 or Layer-4 protocols are supported. From the official github forum, developers of Calico declaims only TCPUDPICMP ad ICMPv6 are supported by Calico. It does make sense that supporting other protocols are a bit harder in such a Layer-3 solution.

Other solutions support all protocols. It’s easy for them to achieve so because either udp encapsulation or VxLAN can support encapsulate L2 packets over L3. So it doesn’t matter what kind of protocol the packet holds.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Protocol Support TCP, UDP, ICMP & ICMPv6 ALL ALL ALL

Name Service

Weave supports a name service between containers. When you create a container, Weave will put it into a DNS name service with format {hostname}.weave.local. Thus you can access to any container with {hostname}.weave.local or simply use {hostname}. The suffix (weave.local) can be changed to other strings, and the DNS lookup service can also be turned off.

The others don’t have such feature.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Name Service No No Yes No

Distributed Storage Requirements

As to CalicoFlannel and Docker Overlay Network, a distributed storage such as Etcd and Consul is a requirement to change routing and host information. Docker Overlay Network can also cooperate with Docker Swarm’s discovery services to build a cluster.

Weave, however, doesn’t need a distributed storage because Weave itself has a node discovery service using Rumor Protocol. This design decouples with another distributed storage system while introduces complexity and consistency concern of IP allocations, as well as the IPAM performance when cluster grows larger.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Distributed Storage Requirements Yes Yes No Yes

Encryption Channel

Flannel supports TLS encryption channel between Flannel and Etcd, as well as data path between Flannel peers. You can see more details on flanneld --help with -etcd-certfile and -remote-certfile parameters.

Weave can be configured to encrypt both control data passing over TCP connections and the payloads of UDP packets sent between peers. This is accomplished with the NaCl crypto libraries employing Curve25519, XSalsa20 and Poly1305 to encrypt and authenticate messages. Weave protects against injection and replay attacks for traffic forwarded between peers.

Calico and Docker Overlay Network doesn’t support any kinds of encryption method, neither Calico-Etcd channel nor data path between Calico peers. But Calico achieves best performance among these four solutions, so it’s better fit for an internal environment or if you don’t care about data safety.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Encryption Channel No TLS NaCl Library No

Partially Connected Network Support

Weave can be deployed in a partially connected network, a brief example is as follows:

There are four peers with peer 1~3 connect with each other and peer 4 only connects to peer3. Weave can be deployed on peer 1~4. Any traffic from containers on peer 1 to containers on peer 4 will be traversed via peer 3.

This feature allows Weave connects hosts aparted by a firewall, thus connects hosts with internal IP address in different data centers.

Others don’t have such feature.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Partially Connected Network Support No No Yes No

Seperate vNIC for Container

Since Weave and Docker Overlay Network create a bridged device and a veth inner containers, they create a seperate vNIC for containers. Routing table of container is also changed, thus bypass all packets of clustered network to this newly created NIC. Other connections, such as google.com, will route to the original vNIC.

Calico can use a unified vNIC for container because it’s a pure Layer-3 solution. Calico can configure NAT for out-going requests and forward subnet packages to other Calico peers. Calico can also use Docker bridged NIC for out-going requests with some manual configuration inner containers. In this way, you need to add -cap-add=Net_Admin parameter when execute docker run.

Flannel directly use docker local bridge docker0 to handle all the transportation, so containers with Flannel network will only see one vNIC inside.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Seperate vNIC for Container No No Yes yes

IP Overlap Support

Technically, for VxLAN-based solutions, tenant networks can have overlapping internal IP address, though IP addresses assigned to hosts must be unique. According to VxLAN speculations, WeaveFlannel and Docker Overlay Network can support IP overlap for containers. But on my testing environment, I cannot configure any of these three support IP overlap. So I can only say they have potential to support IP overlap.

Calico cannot support IP overlap technically, but Calico official documents emphasize that they can put overlapping IPv4 containers’ packets on IPv6 network. Although this is an alternative solution for IPv4 network, I prefer to treate Calico not support IP overlap.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
IP Overlap Support No Maybe Maybe Maybe

Container Subnet Restriction

This section focus on whether container subnet can overlap with host network.

Flannel creates a real bridged network on the host with the subnet address, and use host Linux routing table to forward container packages to this bridge device. So container’s subnet of Flannel cannot be overlap with host network, or host’s routing table will be confused.

Calico is a pure Layer-3 implementation and packets from container to outter world will tranverse NAT table. So Calico also has such restriction that container subnet cannot overlap with host network.

Weave doesn’t use host routing table to differentiate packages from containers, but use the pcap feature to deliver packages to the right place. So Weave doesn’t need to obey the subnet restriction and it’s free to allocate container a same IP address as host. Besides you can also change IP configurations inner container and the container could be reached by the new IP.

Docker Overlay Network allows container and host in the same subnet and achieve the isolation between them. But Docker Overlay Network rely on etcd to record routing information, so changing container’s IP address manually will mess the routing process can lead container beyond reach.

Brief conclusion:

 CalicoFlannelWeaveDocker Overlay Network
Container Subnet Restriction No No Yes, configurable after start Yes, not configurable after start

Conclusion

So let’s give a final conclusion of all the aspects into one table. This table is one of the best references for you to choose a right multi-host networking solution.

 CalicoFlannelWeaveDocker Overlay Network
Network Model Pure Layer-3 Solution VxLAN or UDP Channel VxLAN or UDP Channel VxLAN
Application Isolation Profile Schema CIDR Schema CIDR Schema CIDR Schema
Protocol Support TCP, UDP, ICMP & ICMPv6 ALL ALL ALL
Name Service No No Yes No
Distributed Storage Requirements Yes Yes No Yes
Encryption Channel No TLS NaCl Library No
Partially Connected Network Support No No Yes No
Seperate vNIC for Container No No Yes yes
IP Overlap Support No Maybe Maybe Maybe
Container Subnet Restriction No No Yes, configurable after start Yes, not configurable after start

My future plan is to test the performance of these four multi-host network solutions. Since there are too many contents on this post, I will create a new post to show the details of performance test.

 

 

参考资料:

云数据中心网络虚拟化——大二层技术巡礼之大二层技术小结:  http://www.sdnlab.com/16169.html

SDNLAB技术分享(十五):容器网络大观: http://www.sdnlab.com/17141.html

Pipework、Weave、Flannel各自的优势和区别:  http://dockone.io/question/259

Calico在Docker中的搭建:  http://www.cnblogs.com/tingfengainiaini/p/5010696.html

Battlefield: Calico, Flannel, Weave and Docker Overlay Network : http://chunqi.li/2015/11/15/Battlefield-Calico-Flannel-Weave-and-Docker-Overlay-Network/

Neutron 理解 (3): Open vSwitch + GRE/VxLAN 组网 :http://geek.csdn.net/news/detail/69011

http://geek.csdn.net/user/publishlist/qq_34043421

简析TCP的三次握手与四次分手:  http://www.jellythink.com/archives/705

 

 

瞻博网络发布首款软件定义网络软件——OpenContrail: http://www.infoq.com/cn/news/2013/11/open-contrail-sdn

https://github.com/Juniper/contrail-controller

OpenContrail 体系架构文档  :  http://blog.163.com/s_zhchluo/blog/static/15014708201411144244468/

http://www.opencontrail.org/opencontrail-architecture-documentation/

https://www.sdxcentral.com/articles/news/calico-flannel-tigera-new-container-networking-startup/2016/05/

https://github.com/tigera/canal

 

 

 

posted @ 2016-12-27 16:42  junneyang  阅读(1502)  评论(2编辑  收藏  举报