ABB AC900F学习笔记51:Freelance_Mounting_and_Installation_AC_900F_Controller-11
今天进厂加班,还是比较顺利,原以为要两三天才能做完,半天就做的差不多了,周一再和同事们确认一下。
晚上继续学习和翻译吧,我发现一旦惰性了,就难回过来了,所以还是得保持学习的劲头。
3.2.2 CI 773F PROFIBUS-DP Master Interface
CI 773 PROFIBUS-DP主站接口
The CI 773F is the CM 772F successor model. It provides additional features and sufficient memory (I/O bytes) for the maximum number of PROFIBUS slaves。
CI 773模块是CI 772的后续型号。它为最大PROFIBUS 从站连接提供了足够的内存(IO字节)
Features
|
|
Protocol
协议
|
PROFIBUS-DP master V0/V1
PROFIBUS-DP主站
|
Fieldbus connection
现场总线连接
|
D-SUB, 9-pin, female connector
9针接口,母头
|
Internal power supply
内部供电
|
Via coupler bus
通过耦合器总线
|
LEDs
LED灯
|
Four for status display
四个状态显示灯
|
Use
用于
|
AC 700F, AC 900F
|
Form factor
|
AC 700F, |
Number of slaves
从站数量
|
125 |
Controller redundancy support
支持控制器冗余
|
YES 支持 |
Hot plug
热插拔
|
YES 支持 |
HCIR
|
YES 支持 |
LED status displays
LED灯显示
After having been switched on, the CI 773 PROFIBUS module performs a self-test during power-up. During initialization, with newly configured modules or after a change of the operating mode, all LEDs may light up briefly before reaching the defined status.
上电后,CI 773 PROFIBUS模板执行自检。在初始化过程中,使用新配置的模块或在操作模式更改后,所有 LED 可能会在达到定义状态之前短暂亮起。
LED LED灯 |
Color 颜色 |
Status 状态 |
Meaning 含义 |
PWR 电源灯 |
Green 绿色 |
ON 亮 |
Module in operation and must not be removed
模板正在使用,不能拆除模板
|
OFF 灭 |
Module not in operation and may be removed, if required
模板没有使用,可以拆除模板
|
||
STA 状态灯 |
Green 绿色 |
ON 亮 |
Active module operating properly
活动模块,正常运行
|
OFF 灭 |
Module start-up 模块启动 |
||
Orange 橙色 |
ON 亮 |
Module identified by the CPU module, but not active
CPU识别出模块,但模块没有运行
|
|
Red 红色 |
ON 亮 |
Module error
模块错误
|
|
Run 运行灯 |
Green 绿色 |
ON 亮 |
Module has taken over the PROFIBUS master function
模块接管“主”功能
|
OFF 灭 |
Module inactive relative to the PROFIBUS 模板的PROFIBUS非活动状态 |
||
Green 绿色 |
200ms plus |
Module ready to take over the master function 模板准备接管“主”功能 |
|
LED L |
Green 绿色 |
ON 亮 |
Bus traffic
总线通讯
|
OFF 灭 |
No bus traffic
无总线通讯
|