ABB AC900F学习笔记50:Freelance_Mounting_and_Installation_AC_900F_Controller-10
3.2 CI/CM PROFIBUS modules
CI/CM PROFIBUS模板
The AC 900F is designed for operation with different PROFIBUS communication interfaces like the CI 930F, CI 773F and CM 772F that can be connected on the left side of the PM CPU module。
AC 900F 专为具有不同 PROFIBUS 通信的操作而设计,像CI 930F、CI 773F和CM 772F这样可以在左侧连接PM CPU模块的一侧。
![]() |
The module type CM 772F is supported by PM 901F and PM 902F, but not by PM 904F. CM 772只能被PM 901F和PM 902F,不能被PM 904F支持 |
PROFIBUS communication interfaces ensure communication via the PROFIBUSDP Fieldbus. The internal coupler bus connects the CI/CM with the CPU module. This applies to data and power supply. A dual-port RAM is used for data exchange
PROFIBUS通讯接口确保通过PROFIBUS DP现场总线进行通讯。内部耦合器总线将CI/CM和CPU模板连接起来。这适用于数据和电源(指的是通过内部耦合器)。双端口RAM适用于数据交换。
3.2.1 CI 930F PROFIBUS-DP Master Interface
CI 930F PROFIBUS-DP主站接口
The below description applies to CI 930F with ordering numbers 3BDH....R0002 and ....R0005 only. CI 930F provides two on-board PROFIBUS interfaces A/B for increased availability regarding PROFIBUS communication
以下描述仅适用于订货编号为3BDH....R0002和3BDH ....R0005 的CI 930F,CI 930F提供了两个板载PROFIBUS接口A/B以提升PROFIBUS通讯可用性。
LEDs for status display LED状态显示灯
Label 标签
PROFIBUS Interface A Profibus通讯接口A
PROFIBUS Interface B Profibus通讯接口B
Data arriving at CI 930F via the coupler bus are routed in parallel to both A and B connections. The first data coming in over line A or line B with a correct telegram start are routed to the coupler bus. With simultaneity, either line A or line B is selected at random. Testing and selection is always based on the first character. In the case of a telegram start with error on A, the control logic in CI 930F switches to the redundant line B. The same procedure applies vice-versa for line B.
数据通过耦合器总线到达 CI 930F , A 和 B 连接为平行路由。线路A或者线路B是第一批使用正确报文开头的数据到耦合器总线的路径。伴随同步性,选择线路A还是线路B是随机的。测试和选择始终基于第一个字符、在报文开头出错的情况下,CI930F的控制逻辑会切换到线路B,同样的道理,如果B线路出错,会自动切换到A。
Features 功能 |
|
Protocol 协议 |
PROFIBUS-DP master V0/V1 PROFIBUS-DP主 |
Fieldbus connection 现场总线连接 |
D-SUB, 9-pin, female connector 9针母头 |
Internal power supply 内部供电 |
Via coupler bus 通过耦合器总线 |
LEDs LED灯 |
Five LEDs for status display |
Use 用于 |
AC 900F |
Form factor 外形 |
AC 900F |
Number of slaves 可挂从站数量 |
125 |
Controller redundancy support 支持冗余控制器 |
YES |
Hot plug 热插拔 |
YES |
HCIR | YES |
Line redundancy 线路冗余 |
YES |
LED status displays
LED灯状态显示
After having been switched on, the CI 930 PROFIBUS module performs a self-test during power-up. During initialization, with newly configured modules or after a change of the operating mode, all LEDs may light up briefly before reaching the defined status.
上电后,CI 930 PROFIBUS模板执行自检。在初始化过程中,使用新配置的模块或在操作模式更改后,所有 LED 可能会在达到定义状态之前短暂亮起。
Line redundancy OFF
LED A (line A)
LED 灯 |
Color 颜色 |
Status 状态 |
Meaning 含义 |
PWR 电源灯 |
GREEN 绿色 |
ON 亮 |
Module in operation and must not be removed 模板正在使用,不能被拆除 |
OFF 灭 |
Module not in operation and may be removed, if required 模板没有使用,如果需要,可以拆除 |
||
STA 状态灯
|
Green 绿色
|
ON 亮 |
Active module operating properly 活动模块,正常运行 |
OFF 灭 |
Module start-up 模块启动 |
||
Orange 橙色 |
ON 亮 |
Module identified by the CPU module, but inactive CPU识别出模块,但模块没有运行
|
|
Red 红色 |
ON 亮 |
Module error 模板错误 |
|
RUN 运行灯 |
GREEN 绿色 |
ON 亮 |
Module has taken over the master function 模块接管“主”功能 |
OFF 灭 |
Module inactive relative to the PROFIBUS 模板的PROFIBUS非活动状态 |
||
GREEN 绿色 |
200ms plus |
Module ready to take over the master function 模板计划接管“主”功能 |
|
Line redundancy OFF 线路冗余灭 | |||
LED A (Line A) |
GREEN |
ON 亮 |
Bus traffic 有总线通讯 |
OFF 灭 |
No bus traffic 无总线通讯 |
Line redundancy ON 冗余线路灯亮 |
||||
LED A(Line A) | LED B(Line B) |
LED A and B must be considered as a pair LED A和LED B必须视为成对 |
||
Color 颜色 |
Status 状态 |
Color 颜色 |
Status 状态 |
|
GREEN 绿色 |
ON 亮 |
GREEN 绿色 |
ON 亮 |
Data reception on both lines, A and B A和B两路数据接收 |
OFF 灭 |
OFF 灭 |
No data reception on lines A and B A和B没有数据接收 |
||
RED 红色 |
ON 亮 |
GREEN 绿色 |
ON 亮 |
No data reception on line A, but data reception on line B 线路A没有数据接收,线路B有数据接收 |
GREEN | ON | RED | ON |
No data reception on line B, but data reception on line A 线路B没有数据接收,线路A有数据接收 |