交换机VLAN、 TRUNK 、VTP 配置
交换机VLAN、 TRUNK 、VTP 配置
1． 配置 CISCO 二层交换机的IP 地址(catalyst 2950 为例)
SW1(config)#int vlan 1 //进入管理接口interface vlan 1
SW1(config-if)#ip address 11.1.1.2 255.255.255.0 //配置IP 地址
SW1(config-if)#no shutdown
SW1(config-if)#exit
SW1(config)#ip default-gateway 11.1.1.1 //配置网关,可通过show run 查
查看所配置的 IP 地址:
SW1#show int vlan 1
Vlan1 is up, line protocol is up
Hardware is CPU Interface, address is 0008.20ff.6400 (bia 0008.20ff.6400)
Internet address is 11.1.1.2/24
2．配置交换机的端口速度和双工（Speed and Duplex）
SW1(config)#interface fa0/1
SW1(config-if)#speed {10 | 100 | auto} //10M/100M/自适应
SW1(config-if)#duplex {auto | full | half} //自适应/全双工/半双工
一般情况下,交换机两端的端口速度和双工要匹配,这样通信质量才能得到保证,在相同厂家的产品
（比如说Cisco 的交换机互连）中端口协商不用配置一般不会有什么问题，可以通过show interface 查
看端口的速度和双工。通常在不同厂家的产品中（比如说Cisco 和华为互连）如果通过查看发现端口速
度和双工不匹配，可以通过手工配置来解决。如图:
通过 show interface 查看端口的速度和双工:
SW1#show interfaces fastEthernet 0/24
FastEthernet0/24 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0008.20ff.6418 (bia 0008.20ff.6418)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 100BaseTX
input flow-control is unsupported output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:03, output 00:00:00, output hang never
注：CISCO 交换机端口默认值:Auto-duplex, Auto-speed, media type is 100BaseTX
Cisco 设备配置端口速度（speed）和双工（duplex）命令：
SW1(config)#interface fastEthernet 0/24
SW1(config-if)#speed ?
10 Force 10 Mbps operation ----------------------------注：强制速度为10M
100 Force 100 Mbps operation---------------------------注：强制速度为100M
auto Enable AUTO speed configuration -----------------注：速度自动协议（默认值）
SW1(config-if)#duplex ?
auto Enable AUTO duplex configuration ----------------注：自动协商双工
full Force full duplex operation ---------------------------注：强制为全双工
half Force half-duplex operation --------------------------注：强制为半双工
3．设置永久MAC 地址不过期
SW1(config)#mac-address-table static mac_addr {vlan vlan_id} [interface int1 [int2 ... int15]]
SW1(config)#mac-address-table static 1111.1111.a111 vlan 1 interface f0/1
配置后show mac-address-table 可以看到静态添加的MAC 地址1111.1111.a111
SW1#show mac-address-table
Vlan Mac Address Type Ports
---- ----------- -------- -----
All 000f.72db.4ec0 STATIC CPU
1 1111.1111.a111 STATIC Fa0/1
4．管理MAC 地址表
SW1#show mac-address-table
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports
---- ----------- -------- -----
All 000f.72db.4ec0 STATIC CPU
1 0000.0c3f.0b05 DYNAMIC Fa0/12
1 0030.94e6.391d DYNAMIC Fa0/11
1 00e0.b05a.5bfe DYNAMIC Fa0/10
1 1111.1111.a111 STATIC Fa0/1
5.设置交换机端口的访问模式(三种) access /dynamic / trunk
SW1(config-if)#switchport mode ?
access Set trunking mode to ACCESS unconditionally
dynamic Set trunking mode to dynamically negotiate access or trunk mode
trunk Set trunking mode to TRUNK unconditionally
SW1(config)#int fastEthernet 0/1
SW1(config-if)#switchport mode access //设置FA0/1 为ACCESS 模式
SW1(config-if)#switchport mode trunk //设置FA0/1 为TRUNK 模式
SW1(config-if)#switchport mode dynamic auto //设置FA0/1 为自动直协商模式(默认)
交换机TRUNK 端口配置:
1)一般交换机与交换机相连接的端口要设置为trunk 模式
2 )如果是梳心交换机与非网管的交换机相连,梳心交换机端口设置为access 模式
如下图:
配置 SW1:
SW1(config)#int f0/24
SW1(config-if)#no shutdown
SW1(config-if)#switchport mode trunk //设置FA0/24 为TRUNK 模式
配置 SW2:
SW2(config)#int f0/24
SW2(config-if)#no shutdown
SW2(config-if)#switchport mode trunk //设置FA0/24 为TRUNK 模式
验证 TRUNK 命令:
Show interface trunk
Show interface f0/24 switchport
SW1#sho run int f0/24
interface FastEthernet0/24
switchport mode trunk
SW1#show int trunk
Port Mode Encapsulation Status Native vlan
Fa0/24 on 802.1q trunking 1
SW1#show int f0/24 switchport
Name: Fa0/24
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Appliance trust: none
SW1#
SW2:
SW2#sho run int f0/24
interface FastEthernet0/24
switchport mode trunk
end
SW2#show int trunk
Port Mode Encapsulation Status Native vlan
Fa0/24 on 802.1q trunking 1
6.配置VLAN
1）.创建VLAN
SW1(config)#vlan 2 //创建VLAN2
SW1(config)#name VLAN2 //命名为VLAN2,默认为vlan002,命名是可选命令
2）.将端口加入VLAN
SW1(config-if)#switchport mode access //设配端口为access 模式
SW1(config-if)#switchport access vlan 2 //把端口加到vlan2
3）.检查的命令
Switch#show vlan
例子：
创建 VLAN2 命令为widom ,
创建VLAN3 命令为market
把端口F0/4 加入VLAN2
SW1#config t
SW1(config)#vlan 2
SW1(config-vlan)#name wisdom
SW1(config-vlan)#exit
SW1(config)#vlan 3
SW1(config-vlan)#name market
SW1(config-vlan)#exit
SW1(config)#int fas0/4
SW1(config-if)#switchport mode access
SW1(config-if)#switchport access vlan 2
可以同时把多个端口加入到相应VLAN
SW1(config)#interface range fastEthernet 0/10 – 15 //可以同时把多个端口加入到一个VLAN 里
SW1(config-if-range)#switchport mode access
SW1(config-if-range)#switchport access vlan 3 //把端口10-15 都加入到VLAN3 里
SW1#show vlan //检查VLAN 信息
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24
2 wisdom active Fa0/4
3 market active Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15
SW1#
7.配置VTP----VTP 技术使得在大型的网络里布置多个VLAN 变得简单.
VTP 的配置步骤:
1、配置Trunk (交换机和交换机相连的端口要设置为TRUNK)
2、配置VTP DOMAIN
3、配置VTP MODE
4、配置VLAN
5、将端口加入VLAN
6、检查
Switch#show interface xx/xx switchport //查看相应该接口的trunk 状态
Switch#show vtp status //查看vtp 状态
Switch#show vlan //查看VLAN
配置 SW1:
SW1#configure terminal
SW1(config)#interface fastEthernet 0/24
SW1(config-if)#switchport mode trunk
SW1(config-if)#no shutdown
SW1(config-if)#exit
SW1(config)#vtp domain wisdom
Domain name already set to wisdom.
SW1(config)#vtp mode server
Device mode already VTP SERVER.
SW1(config)#vtp password cisco
Setting device VLAN database password to cisco
SW1(config)#vtp pruning //配置VTP 的修剪,只要在SERVER 端配置就行.
Pruning switched on
SW1#sho vtp status
VTP Version : 2
Configuration Revision : 1
Maximum VLANs supported locally : 64
Number of existing VLANs : 5
VTP Operating Mode : Server
VTP Domain Name : wisdom
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0xE8 0x5A 0x7D 0xB1 0x0E 0xBC 0xEB 0x1F
Configuration last modified by 11.1.1.2 at 3-1-93 02:56:31
Local updater ID is 11.1.1.2 on interface Vl1 (lowest numbered VLAN interface found)
创建 VLAN2 VLAN3 VLAN4 VLAN5
SW1(config)#vlan 2
SW1(config-vlan)#vlan 3
SW1(config-vlan)#vlan 4
SW1(config-vlan)#vlan 5
SW1(config-vlan)#
在 SW1 上创建VLAN 后查看修订版本:
SW1#show vtp status
VTP Version : 2
Configuration Revision : 5
Maximum VLANs supported locally : 128
Number of existing VLANs : 9
VTP Operating Mode : Server
VTP Domain Name : wisdom
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x9C 0x64 0xD6 0x44 0x5E 0x54 0x9E 0xFC
Configuration last modified by 11.1.1.2 at 3-1-93 02:59:04
Local updater ID is 11.1.1.2 on interface Vl1 (lowest numbered VLAN interface found)
在交换机 SW1 上检查已创建的VLAN
SW1#sho vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/5, Fa0/6, Fa0/7
Fa0/8, Fa0/9, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24
2 VLAN0002 active
3 VLAN0003 active
4 VLAN0004 active
5 VLAN0005 active
检查 trunk 端口:
SW1#show interfaces fastEthernet 0/24 switchport
Name: Fa0/24
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Appliance trust: none
配置 SW2:
Switch#
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
SW2(config)#hostname SW2
SW2(config)#int fastEthernet 0/24
SW2(config-if)#switchport mode trunk
SW2(config-if)#exit
SW2(config)#vtp domain wisdom
Changing VTP domain name from test to wisdom
SW2(config)#vtp mode client
Setting device to VTP CLIENT mode.
SW2(config)#vtp password cisco
Setting device VLAN database password to cisco
SW2(config)#
查看 F0/24 的trunk 状态:
SW2#show interfaces fastEthernet 0/24 switchport
Name: Fa0/24
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Administrative Trunking Encapsulation: dot1q
Operational Trunking Encapsulation: dot1q
Negotiation of Trunking: On
Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default)
Voice VLAN: none
Administrative private-vlan host-association: none
Administrative private-vlan mapping: none
Administrative private-vlan trunk native VLAN: none
Administrative private-vlan trunk encapsulation: dot1q
Administrative private-vlan trunk normal VLANs: none
Administrative private-vlan trunk private VLANs: none
Operational private-vlan: none
Trunking VLANs Enabled: ALL
Pruning VLANs Enabled: 2-1001
Capture Mode Disabled
Capture VLANs Allowed: ALL
Protected: false
Appliance trust: none
查看 VTP 状态:
SW2#show vtp status
VTP Version : 2
Configuration Revision : 5
Maximum VLANs supported locally : 128
Number of existing VLANs : 9
VTP Operating Mode : Client
VTP Domain Name : wisdom
VTP Pruning Mode : Enabled
VTP V2 Mode : Disabled
VTP Traps Generation : Disabled
MD5 digest : 0x9C 0x64 0xD6 0x44 0x5E 0x54 0x9E 0xFC
Configuration last modified by 11.1.1.2 at 3-1-93 02:59:04
----------此处可以看到SW2 的VLAN 信息是从SW1-11.1.1.2 同步过来的
SW2#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/2, Fa0/3, Fa0/4, Fa0/5
Fa0/6, Fa0/7, Fa0/8, Fa0/9
Fa0/10, Fa0/11, Fa0/12, Fa0/13
Fa0/14, Fa0/15, Fa0/16, Fa0/17
Fa0/18, Fa0/19, Fa0/20, Fa0/21
Fa0/22, Fa0/23, Fa0/24
2 VLAN0002 active
3 VLAN0003 active
4 VLAN0004 active
5 VLAN0005 active
实验结果：
SW2 不用配置VLAN,已同步了SW1 的VLAN 信息.实验成功
SW2 同步VTP SERVER 的VLAN 后,接下来的操作就是安要求把相应的端口加入到相应的VLAN
