在鲲鹏920服务器上编译和安装dpdk踩坑（二）

网卡配置如下

注意：使用VFIO需要BIOS开启SMMU

[root@localhost dpdk-19.11]# ethtool -i enp6s0
driver: hinic
version: 
firmware-version: 
expansion-rom-version: 
bus-info: 0000:06:00.0
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
[root@localhost dpdk-19.11]#

[root@localhost dpdk-19.11]# lspci | grep -i ether 
05:00.0 Ethernet controller: Huawei Technologies Co., Ltd. Hi1822 Family (2*25GE) (rev 45)
06:00.0 Ethernet controller: Huawei Technologies Co., Ltd. Hi1822 Family (2*25GE) (rev 45)
7d:00.0 Ethernet controller: Huawei Technologies Co., Ltd. HNS GE/10GE/25GE RDMA Network Controller (rev 21)
7d:00.1 Ethernet controller: Huawei Technologies Co., Ltd. HNS GE/10GE/25GE Network Controller (rev 21)
7d:00.2 Ethernet controller: Huawei Technologies Co., Ltd. HNS GE/10GE/25GE RDMA Network Controller (rev 21)
7d:00.3 Ethernet controller: Huawei Technologies Co., Ltd. HNS GE/10GE/25GE Network Controller (rev 21)

1、升级驱动

https://support.huawei.com/enterprise/zh/management-software/taishanserver-idriver-pid-251215329/software/251215334?idAbsPath=fixnode01%7C7919749%7C9856522%7C9856629%7C251215329

安装依赖包

yum install pciutils -y

支持华为驱动

dpdk-19.11./config/common_base文件中的板载网卡PMD驱动开关：

Line 286: # Compile burst-oriented HNS3 PMD driver

Line 288: CONFIG_RTE_LIBRTE_HNS3_PMD=y

[root@localhost dpdk-19.11]# grep -n CONFIG_RTE_LIBRTE_HNS3_PMD  config/common_base 
288:CONFIG_RTE_LIBRTE_HNS3_PMD=n

[root@localhost dpdk-19.11]# grep -n CONFIG_RTE_LIBRTE_HNS3_PMD config/common_base
288:CONFIG_RTE_LIBRTE_HNS3_PMD=y
[root@localhost dpdk-19.11]#

1)        编译DPDK19.11版本需要gcc5.0及以上版本，本文推荐使用gcc7.3.0

yum install -y *gcc*

yum install -y *glibc*

yum install -y *stdc*

yum install –y *gfortran*

yum install –y m4

yum install -y numactl*

yum install -y automake

[root@localhost dpdk-19.11]# ls /sys/kernel/mm/hugepages/
hugepages-2048kB  hugepages-524288kB
[root@localhost dpdk-19.11]#  grep Hugepagesize /proc/meminfo
Hugepagesize:     524288 kB
[root@localhost dpdk-19.11]# cat   /sys/devices/system/node/node*/meminfo |grep -i huge
Node 0 AnonHugePages:         0 kB
Node 0 ShmemHugePages:        0 kB
Node 0 HugePages_Total:     0
Node 0 HugePages_Free:      0
Node 0 HugePages_Surp:      0
Node 1 AnonHugePages:         0 kB
Node 1 ShmemHugePages:        0 kB
Node 1 HugePages_Total:     0
Node 1 HugePages_Free:      0
Node 1 HugePages_Surp:      0
Node 2 AnonHugePages:         0 kB
Node 2 ShmemHugePages:        0 kB
Node 2 HugePages_Total:     0
Node 2 HugePages_Free:      0
Node 2 HugePages_Surp:      0
Node 3 AnonHugePages:         0 kB
Node 3 ShmemHugePages:        0 kB
Node 3 HugePages_Total:     0
Node 3 HugePages_Free:      0
Node 3 HugePages_Surp:      0
[root@localhost dpdk-19.11]#

运行

./usertools/dpdk-setup.sh

选择其中的选项49：设置大页，让每个numa node均分同样的大页数量

[root@localhost dpdk-19.11]# ./usertools/dpdk-setup.sh
------------------------------------------------------------------------------
 RTE_SDK exported as /root/dpdk-19.11
------------------------------------------------------------------------------
----------------------------------------------------------
 Step 1: Select the DPDK environment to build
----------------------------------------------------------
[1] arm64-armada-linuxapp-gcc
[2] arm64-armada-linux-gcc
[3] arm64-armv8a-linuxapp-clang
[4] arm64-armv8a-linuxapp-gcc
[5] arm64-armv8a-linux-clang
[6] arm64-armv8a-linux-gcc
[7] arm64-bluefield-linuxapp-gcc
[8] arm64-bluefield-linux-gcc
[9] arm64-dpaa-linuxapp-gcc
[10] arm64-dpaa-linux-gcc
[11] arm64-emag-linuxapp-gcc
[12] arm64-emag-linux-gcc
[13] arm64-n1sdp-linuxapp-gcc
[14] arm64-n1sdp-linux-gcc
[15] arm64-octeontx2-linuxapp-gcc
[16] arm64-octeontx2-linux-gcc
[17] arm64-stingray-linuxapp-gcc
[18] arm64-stingray-linux-gcc
[19] arm64-thunderx2-linuxapp-gcc
[20] arm64-thunderx2-linux-gcc
[21] arm64-thunderx-linuxapp-gcc
[22] arm64-thunderx-linux-gcc
[23] arm64-xgene1-linuxapp-gcc
[24] arm64-xgene1-linux-gcc
[25] arm-armv7a-linuxapp-gcc
[26] arm-armv7a-linux-gcc
[27] i686-native-linuxapp-gcc
[28] i686-native-linuxapp-icc
[29] i686-native-linux-gcc
[30] i686-native-linux-icc
[31] ppc_64-power8-linuxapp-gcc
[32] ppc_64-power8-linux-gcc
[33] x86_64-native-bsdapp-clang
[34] x86_64-native-bsdapp-gcc
[35] x86_64-native-freebsd-clang
[36] x86_64-native-freebsd-gcc
[37] x86_64-native-linuxapp-clang
[38] x86_64-native-linuxapp-gcc
[39] x86_64-native-linuxapp-icc
[40] x86_64-native-linux-clang
[41] x86_64-native-linux-gcc
[42] x86_64-native-linux-icc
[43] x86_x32-native-linuxapp-gcc
[44] x86_x32-native-linux-gcc

----------------------------------------------------------
 Step 2: Setup linux environment
----------------------------------------------------------
[45] Insert IGB UIO module
[46] Insert VFIO module
[47] Insert KNI module
[48] Setup hugepage mappings for non-NUMA systems
[49] Setup hugepage mappings for NUMA systems
[50] Display current Ethernet/Baseband/Crypto device settings
[51] Bind Ethernet/Baseband/Crypto device to IGB UIO module
[52] Bind Ethernet/Baseband/Crypto device to VFIO module
[53] Setup VFIO permissions

----------------------------------------------------------
 Step 3: Run test application for linux environment
----------------------------------------------------------
[54] Run test application ($RTE_TARGET/app/test)
[55] Run testpmd application in interactive mode ($RTE_TARGET/app/testpmd)

----------------------------------------------------------
 Step 4: Other tools
----------------------------------------------------------
[56] List hugepage info from /proc/meminfo

----------------------------------------------------------
 Step 5: Uninstall and system cleanup
----------------------------------------------------------
[57] Unbind devices from IGB UIO or VFIO driver
[58] Remove IGB UIO module
[59] Remove VFIO module
[60] Remove KNI module
[61] Remove hugepage mappings

[62] Exit Script

Option:

[root@localhost dpdk-19.11]# echo 256 >   /sys/kernel/mm/hugepages/hugepages-524288kB/nr_hugepages
[root@localhost dpdk-19.11]# cat   /sys/devices/system/node/node*/meminfo |grep -i huge
Node 0 AnonHugePages:         0 kB
Node 0 ShmemHugePages:        0 kB
Node 0 HugePages_Total:    64
Node 0 HugePages_Free:     64
Node 0 HugePages_Surp:      0
Node 1 AnonHugePages:         0 kB
Node 1 ShmemHugePages:        0 kB
Node 1 HugePages_Total:    64
Node 1 HugePages_Free:     64
Node 1 HugePages_Surp:      0
Node 2 AnonHugePages:         0 kB
Node 2 ShmemHugePages:        0 kB
Node 2 HugePages_Total:    64
Node 2 HugePages_Free:     64
Node 2 HugePages_Surp:      0
Node 3 AnonHugePages:         0 kB
Node 3 ShmemHugePages:        0 kB
Node 3 HugePages_Total:    64
Node 3 HugePages_Free:     64
Node 3 HugePages_Surp:      0

[root@localhost dpdk-19.11]# umount /mnt
[root@localhost dpdk-19.11]#   mkdir -p /mnt/huge
[root@localhost dpdk-19.11]# mount -t hugetlbfs none /mnt/huge
[root@localhost dpdk-19.11]# grep -i  hugepage /proc/meminfo 
AnonHugePages:         0 kB
ShmemHugePages:        0 kB
HugePages_Total:     256
HugePages_Free:      256
HugePages_Rsvd:        0
HugePages_Surp:        0
Hugepagesize:     524288 kB

编译报错

输出make日志

yum install kernel-devel

[root@localhost dpdk-19.11]# ln -sf /usr/src/kernels/4.18.0-193.28.1.el7.aarch64/  /lib/modules/4.14.0-115.el7a.0.1.aarch64/build 
[root@localhost dpdk-19.11]# ls  /usr/src/kernels/ -al
total 4
drwxr-xr-x.  3 root root   41 Jun 10 02:46 .
drwxr-xr-x.  4 root root   34 Jun  9 23:15 ..
drwxr-xr-x. 23 root root 4096 Jun 10 02:46 4.18.0-193.28.1.el7.aarch64
[root@localhost dpdk-19.11]#

make -j 64 V=2

[root@localhost dpdk-19.11]#  ./usertools/dpdk-devbind.py  -s

Network devices using kernel driver
===================================
0000:05:00.0 'Hi1822 Family (2*25GE) 0200' if=enp5s0 drv=hinic unused= 
0000:06:00.0 'Hi1822 Family (2*25GE) 0200' if=enp6s0 drv=hinic unused= 
0000:7d:00.0 'HNS GE/10GE/25GE RDMA Network Controller a222' if=enp125s0f0 drv=hns3 unused=hns_roce_hw_v2 *Active*
0000:7d:00.1 'HNS GE/10GE/25GE Network Controller a221' if=enp125s0f1 drv=hns3 unused= 
0000:7d:00.2 'HNS GE/10GE/25GE RDMA Network Controller a222' if=enp125s0f2 drv=hns3 unused=hns_roce_hw_v2 
0000:7d:00.3 'HNS GE/10GE/25GE Network Controller a221' if=enp125s0f3 drv=hns3 unused= 

No 'Baseband' devices detected
==============================

No 'Crypto' devices detected
============================

No 'Eventdev' devices detected
==============================

No 'Mempool' devices detected
=============================

No 'Compress' devices detected
==============================

No 'Misc (rawdev)' devices detected
===================================
[root@localhost dpdk-19.11]#

[root@localhost dpdk-19.11]# modprobe vfio
[root@localhost dpdk-19.11]# modprobe   vfio-pci
选择其中的选项53：增加VFIO permission
[root@localhost dpdk-19.11]# ./usertools/dpdk-setup.sh

[root@localhost dpdk-19.11]# ethtool enp5s0
Settings for enp5s0:
        Supported ports: [ ]
        Supported link modes:   Not reported
        Supported pause frame use: No
        Supports auto-negotiation: Yes
        Supported FEC modes: Not reported
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: Yes
        Advertised FEC modes: Not reported
        Speed: 40000Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: on
        MDI-X: Unknown
        Link detected: yes
[root@localhost dpdk-19.11]# ethtool -i  enp5s0
driver: hinic
version: 
firmware-version: 
expansion-rom-version: 
bus-info: 0000:05:00.0
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
[root@localhost dpdk-19.11]#

[root@localhost dpdk-19.11]# ./usertools/dpdk-devbind.py  -s

Network devices using kernel driver
===================================
0000:05:00.0 'Hi1822 Family (2*25GE) 0200' if=enp5s0 drv=hinic unused=vfio-pci 
0000:06:00.0 'Hi1822 Family (2*25GE) 0200' if=enp6s0 drv=hinic unused=vfio-pci 
0000:7d:00.0 'HNS GE/10GE/25GE RDMA Network Controller a222' if=enp125s0f0 drv=hns3 unused=hns_roce_hw_v2,vfio-pci *Active*
0000:7d:00.1 'HNS GE/10GE/25GE Network Controller a221' if=enp125s0f1 drv=hns3 unused=vfio-pci 
0000:7d:00.2 'HNS GE/10GE/25GE RDMA Network Controller a222' if=enp125s0f2 drv=hns3 unused=hns_roce_hw_v2,vfio-pci 
0000:7d:00.3 'HNS GE/10GE/25GE Network Controller a221' if=enp125s0f3 drv=hns3 unused=vfio-pci

[root@localhost dpdk-19.11]# ./usertools/dpdk-devbind.py  --bind=vfio-pci  0000:05:00.0  0000:06:00.0
绑定成功后用ethtool看不到了

[root@localhost dpdk-19.11]# ethtool -i  enp5s0
Cannot get driver information: No such device
[root@localhost dpdk-19.11]# ethtool -i  enp5s1
Cannot get driver information: No such device
[root@localhost dpdk-19.11]#

/sys/class/net/下也没有了

[root@localhost dpdk-19.11]# cat   /sys/class/net/enp5s0/device/numa_node     
cat: /sys/class/net/enp5s0/device/numa_node: No such file or directory

[root@localhost ~]# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: enp125s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether b0:08:75:5f:b7:d9 brd ff:ff:ff:ff:ff:ff
    inet 10.10.16.229/24 scope global enp125s0f0
       valid_lft forever preferred_lft forever
3: enp125s0f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether b0:08:75:5f:b7:da brd ff:ff:ff:ff:ff:ff
4: enp125s0f2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether b0:08:75:5f:b7:db brd ff:ff:ff:ff:ff:ff
5: enp125s0f3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether b0:08:75:5f:b7:dc brd ff:ff:ff:ff:ff:ff
6: enp5s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 44:a1:91:a4:9b:eb brd ff:ff:ff:ff:ff:ff
7: enp6s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 44:a1:91:a4:9b:ec brd ff:ff:ff:ff:ff:ff
绑定后看不到了
[root@localhost ~]# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: enp125s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether b0:08:75:5f:b7:d9 brd ff:ff:ff:ff:ff:ff
    inet 10.10.16.229/24 scope global enp125s0f0
       valid_lft forever preferred_lft forever
3: enp125s0f1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether b0:08:75:5f:b7:da brd ff:ff:ff:ff:ff:ff
4: enp125s0f2: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether b0:08:75:5f:b7:db brd ff:ff:ff:ff:ff:ff
5: enp125s0f3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether b0:08:75:5f:b7:dc brd ff:ff:ff:ff:ff:ff
[root@localhost ~]#

查看pci 05:00.0 、 06:00.0 的numa

[root@localhost dpdk-19.11]# lspci -vvv   | grep '05:00.0' -A 5
05:00.0 Ethernet controller: Huawei Technologies Co., Ltd. Hi1822 Family (2*25GE) (rev 45)
        Subsystem: Huawei Technologies Co., Ltd. Device d139
        Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
        NUMA node: 0
        Region 0: [virtual] Memory at 80007b00000 (64-bit, prefetchable) [size=128K]
[root@localhost dpdk-19.11]#

[root@localhost dpdk-19.11]# lspci -vvv | grep '06:00.0' -A 5
06:00.0 Ethernet controller: Huawei Technologies Co., Ltd. Hi1822 Family (2*25GE) (rev 45)
Subsystem: Huawei Technologies Co., Ltd. Device d139
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
NUMA node: 0
Region 0: [virtual] Memory at 80010400000 (64-bit, prefetchable) [size=128K]

使用numactl -H 查看对应numa node下的CPU核
[root@localhost dpdk-19.11]# numactl -H 
available: 4 nodes (0-3)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
node 0 size: 130048 MB
node 0 free: 95951 MB
node 1 cpus: 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
node 1 size: 130937 MB
node 1 free: 97039 MB
node 2 cpus: 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95
node 2 size: 130937 MB
node 2 free: 96458 MB
node 3 cpus: 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127
node 3 size: 130935 MB
node 3 free: 95428 MB
node distances:
node   0   1   2   3 
  0:  10  16  32  33 
  1:  16  10  25  32 
  2:  32  25  10  16 
  3:  33  32  16  10

[root@localhost dpdk-19.11]# ls arm64-armv8a-linuxapp-gcc/
app  build  include  kmod  lib  Makefile
[root@localhost dpdk-19.11]# ./arm64-armv8a-linuxapp-gcc/app/testpmd   -l 64-72 -n 8 -w 0000:05:00.0 -w 0000:06:00.0  -- --rxd=1024 --txd=1024   --rxq=1 --txq=1 --nb-cores=4 -i
EAL: Detected 128 lcore(s)
EAL: Detected 4 NUMA nodes
EAL: Multi-process socket /var/run/dpdk/rte/mp_socket
EAL: Selected IOVA mode 'VA'
EAL: No available hugepages reported in hugepages-2048kB
EAL: Probing VFIO support...
EAL: VFIO support initialized
EAL: PCI device 0000:05:00.0 on NUMA socket 0
EAL:   probe driver: 19e5:200 net_hinic
EAL:   using IOMMU type 1 (Type 1)
net_hinic: Initializing pf hinic-0000:05:00.0 in primary process
net_hinic: Device 0000:05:00.0 hwif attribute:
net_hinic: func_idx:0, p2p_idx:0, pciintf_idx:0, vf_in_pf:0, ppf_idx:0, global_vf_id:15, func_type:2
net_hinic: num_aeqs:4, num_ceqs:4, num_irqs:32, dma_attr:2
net_hinic: Get public resource capability:
net_hinic: host_id: 0x0, ep_id: 0x0, intr_type: 0x0, max_cos_id: 0x7, er_id: 0x0, port_id: 0x0
net_hinic: host_total_function: 0xf2, host_oq_id_mask_val: 0x8, max_vf: 0x78
net_hinic: pf_num: 0x2, pf_id_start: 0x0, vf_num: 0xf0, vf_id_start: 0x10
net_hinic: Get share resource capability:
net_hinic: host_pctxs: 0x0, host_cctxs: 0x0, host_scqs: 0x0, host_srqs: 0x0, host_mpts: 0x0
net_hinic: Get l2nic resource capability:
net_hinic: max_sqs: 0x10, max_rqs: 0x10, vf_max_sqs: 0x4, vf_max_rqs: 0x4
net_hinic: Initialize 0000:05:00.0 in primary successfully
EAL: PCI device 0000:06:00.0 on NUMA socket 0
EAL:   probe driver: 19e5:200 net_hinic
net_hinic: Initializing pf hinic-0000:06:00.0 in primary process
net_hinic: Device 0000:06:00.0 hwif attribute:
net_hinic: func_idx:1, p2p_idx:1, pciintf_idx:0, vf_in_pf:0, ppf_idx:0, global_vf_id:135, func_type:0
net_hinic: num_aeqs:4, num_ceqs:4, num_irqs:32, dma_attr:2
net_hinic: Get public resource capability:
net_hinic: host_id: 0x0, ep_id: 0x1, intr_type: 0x0, max_cos_id: 0x7, er_id: 0x1, port_id: 0x1
net_hinic: host_total_function: 0xf2, host_oq_id_mask_val: 0x8, max_vf: 0x78
net_hinic: pf_num: 0x2, pf_id_start: 0x0, vf_num: 0xf0, vf_id_start: 0x10
net_hinic: Get l2nic resource capability:
net_hinic: max_sqs: 0x10, max_rqs: 0x10, vf_max_sqs: 0x4, vf_max_rqs: 0x4
net_hinic: Initialize 0000:06:00.0 in primary successfully
Interactive-mode selected
testpmd: create a new mbuf pool <mbuf_pool_socket_2>: n=211456, size=2176, socket=2
testpmd: preferred mempool ops selected: ring_mp_mc
testpmd: create a new mbuf pool <mbuf_pool_socket_0>: n=211456, size=2176, socket=0
testpmd: preferred mempool ops selected: ring_mp_mc
Configuring Port 0 (socket 0)
net_hinic: Disable vlan filter succeed, device: hinic-0000:05:00.0, port_id: 0
net_hinic: Disable vlan strip succeed, device: hinic-0000:05:00.0, port_id: 0
net_hinic: Set new mac address 44:a1:91:a4:9b:eb

net_hinic: Disable promiscuous, nic_dev: hinic-0000:05:00.0, port_id: 0, promisc: 0
net_hinic: Disable allmulticast succeed, nic_dev: hinic-0000:05:00.0, port_id: 0
Port 0: 44:A1:91:A4:9B:EB
Configuring Port 1 (socket 0)
net_hinic: Disable vlan filter succeed, device: hinic-0000:06:00.0, port_id: 1
net_hinic: Disable vlan strip succeed, device: hinic-0000:06:00.0, port_id: 1
net_hinic: Set new mac address 44:a1:91:a4:9b:ec

net_hinic: Disable promiscuous, nic_dev: hinic-0000:06:00.0, port_id: 1, promisc: 0
net_hinic: Disable allmulticast succeed, nic_dev: hinic-0000:06:00.0, port_id: 1
Port 1: 44:A1:91:A4:9B:EC
Checking link statuses...
Done
net_hinic: Enable promiscuous, nic_dev: hinic-0000:05:00.0, port_id: 0, promisc: 0
net_hinic: Enable promiscuous, nic_dev: hinic-0000:06:00.0, port_id: 1, promisc: 0
testpmd>

testpmd 退出

uio

[root@localhost dpdk-19.11]#  modprobe uio
[root@localhost dpdk-19.11]# find ./ -name igb_uio.ko 
./build/build/kernel/linux/igb_uio/igb_uio.ko
./build/kmod/igb_uio.ko
./arm64-armv8a-linuxapp-gcc/build/kernel/linux/igb_uio/igb_uio.ko ----------------另外一个版本的4.18
./arm64-armv8a-linuxapp-gcc/kmod/igb_uio.ko

[root@localhost dpdk-19.11]# insmod  ./arm64-armv8a-linuxapp-gcc/build/kernel/linux/igb_uio/igb_uio.ko
insmod: ERROR: could not insert module ./arm64-armv8a-linuxapp-gcc/build/kernel/linux/igb_uio/igb_uio.ko: Invalid module format
[root@localhost dpdk-19.11]# uname -a
Linux localhost.localdomain 4.14.0-115.el7a.0.1.aarch64 #1 SMP Sun Nov 25 20:54:21 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
[root@localhost dpdk-19.11]# insmod  ./build/kmod/igb_uio.ko
[root@localhost dpdk-19.11]#

[root@localhost dpdk-19.11]# insmod  ./build/kmod/igb_uio.ko
[root@localhost dpdk-19.11]#  rmmod igb_uio.ko
[root@localhost dpdk-19.11]# insmod  ./build/build/kernel/linux/igb_uio/igb_uio.ko
[root@localhost dpdk-19.11]#

[root@localhost dpdk-19.11]#  ./usertools/dpdk-devbind.py  --bind=igb_uio  0000:06:00.0

https://bbs.huaweicloud.com/forum/thread-27382-1-1.html

https://bbs.huaweicloud.com/forum/thread-40741-1-1.html

posted on 2020-04-14 10:22 tycoon3 阅读(5068) 评论(3) 编辑收藏举报

刷新页面返回顶部

登录后才能查看或发表评论，立即登录或者逛逛博客园首页

阅读排行：
· 震惊！C++程序真的从main开始吗？99%的程序员都答错了
· 单元测试从入门到精通
· 【硬核科普】Trae如何「偷看」你的代码？零基础破解AI编程运行原理
· 上周热点回顾（3.3-3.9）
· winform 绘制太阳，地球，月球运作规律

在鲲鹏920服务器上编译和安装dpdk踩坑（二）

导航

公告

统计

搜索

常用链接

随笔分类

随笔档案

阅读排行榜

评论排行榜

推荐排行榜

最新评论