C# windows API方式操作串口
最近使用.Net下的SerialPort类操作串口，参数正确报错:连到系统上的设备没有发挥作用。使用C++程序调用正常，未找到问题原因，使用windows API 方式打开串口正常。
`
class CommPort {
public string PortNum;
public int BaudRate;
public byte ByteSize;
public byte Parity; // 0-4=no,odd,even,mark,space
public byte StopBits; // 0,1,2 = 1, 1.5, 2
public int ReadTimeout;
//comm port win32 file handle
private int hComm = -1;
public bool Opened = false;
//win32 api constants
private const uint GENERIC_READ = 0x80000000;
private const uint GENERIC_WRITE = 0x40000000;
private const int OPEN_EXISTING = 3;
private const int INVALID_HANDLE_VALUE = -1;
[StructLayout(LayoutKind.Sequential)]
public struct DCB {
//taken from c struct in platform sdk
public int DCBlength; // sizeof(DCB)
public int BaudRate; // 指定当前波特率 current baud rate
// these are the c struct bit fields, bit twiddle flag to set
public int fBinary; // 指定是否允许二进制模式,在windows95中必须主TRUE binary mode, no EOF check
public int fParity; // 指定是否允许奇偶校验 enable parity checking
public int fOutxCtsFlow; // 指定CTS是否用于检测发送控制，当为TRUE是CTS为OFF，发送将被挂起。 CTS output flow control
public int fOutxDsrFlow; // 指定CTS是否用于检测发送控制 DSR output flow control
public int fDtrControl; // DTR_CONTROL_DISABLE值将DTR置为OFF, DTR_CONTROL_ENABLE值将DTR置为ON, DTR_CONTROL_HANDSHAKE允许DTR"握手" DTR flow control type
public int fDsrSensitivity; // 当该值为TRUE时DSR为OFF时接收的字节被忽略 DSR sensitivity
public int fTXContinueOnXoff; // 指定当接收缓冲区已满,并且驱动程序已经发送出XoffChar字符时发送是否停止。TRUE时，在接收缓冲区接收到缓冲区已满的字节XoffLim且驱动程序已经发送出XoffChar字符中止接收字节之后，发送继续进行。 FALSE时，在接收缓冲区接收到代表缓冲区已空的字节XonChar且驱动程序已经发送出恢复发送的XonChar之后，发送继续进行。XOFF continues Tx
public int fOutX; // TRUE时，接收到XoffChar之后便停止发送接收到XonChar之后将重新开始 XON/XOFF out flow control
public int fInX; // TRUE时，接收缓冲区接收到代表缓冲区满的XoffLim之后，XoffChar发送出去接收缓冲区接收到代表缓冲区空的XonLim之后，XonChar发送出去 XON/XOFF in flow control
public int fErrorChar; // 该值为TRUE且fParity为TRUE时，用ErrorChar 成员指定的字符代替奇偶校验错误的接收字符 enable error replacement
public int fNull; // eTRUE时，接收时去掉空（0值）字节 enable null stripping
public int fRtsControl; // RTS flow control
/*RTS_CONTROL_DISABLE时,RTS置为OFF
RTS_CONTROL_ENABLE时, RTS置为ON
RTS_CONTROL_HANDSHAKE时,
当接收缓冲区小于半满时RTS为ON
当接收缓冲区超过四分之三满时RTS为OFF
RTS_CONTROL_TOGGLE时,
当接收缓冲区仍有剩余字节时RTS为ON ,否则缺省为OFF*/
public int fAbortOnError; // TRUE时,有错误发生时中止读和写操作 abort on error
public int fDummy2; // 未使用 reserved
public uint flags;
public ushort wReserved; // 未使用,必须为0 not currently used
public ushort XonLim; // 指定在XON字符发送这前接收缓冲区中可允许的最小字节数 transmit XON threshold
public ushort XoffLim; // 指定在XOFF字符发送这前接收缓冲区中可允许的最小字节数 transmit XOFF threshold
public byte ByteSize; // 指定端口当前使用的数据位 number of bits/byte, 4-8
public byte Parity; // 指定端口当前使用的奇偶校验方法,可能为:EVENPARITY,MARKPARITY,NOPARITY,ODDPARITY 0-4=no,odd,even,mark,space
public byte StopBits; // 指定端口当前使用的停止位数,可能为:ONESTOPBIT,ONE5STOPBITS,TWOSTOPBITS 0,1,2 = 1, 1.5, 2
public char XonChar; // 指定用于发送和接收字符XON的值 Tx and Rx XON character
public char XoffChar; // 指定用于发送和接收字符XOFF值 Tx and Rx XOFF character
public char ErrorChar; // 本字符用来代替接收到的奇偶校验发生错误时的值 error replacement character
public char EofChar; // 当没有使用二进制模式时,本字符可用来指示数据的结束 end of input character
public char EvtChar; // 当接收到此字符时,会产生一个事件 received event character
public ushort wReserved1; // 未使用 reserved; do not use
}
[StructLayout(LayoutKind.Sequential)]
private struct COMMTIMEOUTS {
public int ReadIntervalTimeout;
public int ReadTotalTimeoutMultiplier;
public int ReadTotalTimeoutConstant;
public int WriteTotalTimeoutMultiplier;
public int WriteTotalTimeoutConstant;
}
[StructLayout(LayoutKind.Sequential)]
private struct OVERLAPPED {
public int Internal;
public int InternalHigh;
public int Offset;
public int OffsetHigh;
public int hEvent;
}
[DllImport("kernel32.dll")]
private static extern int CreateFile(
string lpFileName, // 要打开的串口名称
uint dwDesiredAccess, // 指定串口的访问方式，一般设置为可读可写方式
int dwShareMode, // 指定串口的共享模式，串口不能共享，所以设置为0
int lpSecurityAttributes, // 设置串口的安全属性，WIN9X下不支持，应设为NULL
int dwCreationDisposition, // 对于串口通信，创建方式只能为OPEN_EXISTING
int dwFlagsAndAttributes, // 指定串口属性与标志，设置为FILE_FLAG_OVERLAPPED(重叠I/O操作)，指定串口以异步方式通信
int hTemplateFile // 对于串口通信必须设置为NULL
);
//hComm = CreateFile(PortNum ,GENERIC_READ | GENERIC_WRITE,0, 0,OPEN_EXISTING,0,0);
[DllImport("kernel32.dll")]
private static extern bool GetCommState(
int hFile, //通信设备句柄
ref DCB lpDCB // 设备控制块DCB
);
[DllImport("kernel32.dll")]
private static extern bool BuildCommDCB(
string lpDef, // 设备控制字符串
ref DCB lpDCB // 设备控制块
);
[DllImport("kernel32.dll")]
private static extern bool SetCommState(
int hFile, // 通信设备句柄
ref DCB lpDCB // 设备控制块
);
[DllImport("kernel32.dll")]
private static extern bool GetCommTimeouts(
int hFile, // 通信设备句柄 handle to comm device
ref COMMTIMEOUTS lpCommTimeouts // 超时时间 time-out values
);
[DllImport("kernel32.dll")]
private static extern bool SetCommTimeouts(
int hFile, // 通信设备句柄 handle to comm device
ref COMMTIMEOUTS lpCommTimeouts // 超时时间 time-out values
);
[DllImport("kernel32.dll")]
private static extern bool ReadFile(
int hFile, // 通信设备句柄 handle to file
byte[] lpBuffer, // 数据缓冲区 data buffer
int nNumberOfBytesToRead, // 多少字节等待读取 number of bytes to read
ref int lpNumberOfBytesRead, // 读取多少字节 number of bytes read
ref OVERLAPPED lpOverlapped // 溢出缓冲区 overlapped buffer
);
[DllImport("kernel32.dll")]
private static extern bool WriteFile(
int hFile, // 通信设备句柄 handle to file
byte[] lpBuffer, // 数据缓冲区 data buffer
int nNumberOfBytesToWrite, // 多少字节等待写入 number of bytes to write
ref int lpNumberOfBytesWritten, // 已经写入多少字节 number of bytes written
ref OVERLAPPED lpOverlapped // 溢出缓冲区 overlapped buffer
);
[DllImport("kernel32.dll")]
private static extern bool CloseHandle(
int hObject // handle to object
);
[DllImport("kernel32.dll")]
private static extern uint GetLastError();
public void Open()
{
DCB dcbCommPort = new DCB();
COMMTIMEOUTS ctoCommPort = new COMMTIMEOUTS();
// 打开串口 OPEN THE COMM PORT.
hComm = CreateFile(PortNum ,GENERIC_READ | GENERIC_WRITE,0, 0,OPEN_EXISTING,0,0);
// 如果串口没有打开，就打开 IF THE PORT CANNOT BE OPENED, BAIL OUT.
if(hComm == INVALID_HANDLE_VALUE)
{
throw(new ApplicationException("非法操作，不能打开串口！"));
}
// 设置通信超时时间 SET THE COMM TIMEOUTS.
GetCommTimeouts(hComm,ref ctoCommPort);
ctoCommPort.ReadTotalTimeoutConstant = ReadTimeout;
ctoCommPort.ReadTotalTimeoutMultiplier = 0;
ctoCommPort.WriteTotalTimeoutMultiplier = 0;
ctoCommPort.WriteTotalTimeoutConstant = 0;
SetCommTimeouts(hComm,ref ctoCommPort);
// 设置串口 SET BAUD RATE, PARITY, WORD SIZE, AND STOP BITS.
GetCommState(hComm, ref dcbCommPort);
dcbCommPort.BaudRate=BaudRate;
dcbCommPort.flags=0;
//dcb.fBinary=1;
dcbCommPort.flags|=1;
if (Parity>0)
{
//dcb.fParity=1
dcbCommPort.flags|=2;
}
dcbCommPort.Parity=Parity;
dcbCommPort.ByteSize=ByteSize;
dcbCommPort.StopBits=StopBits;
if (!SetCommState(hComm, ref dcbCommPort))
{
//uint ErrorNum=GetLastError();
throw(new ApplicationException("非法操作，不能打开串口！"));
}
//unremark to see if setting took correctly
//DCB dcbCommPort2 = new DCB();
//GetCommState(hComm, ref dcbCommPort2);
Opened = true;
}
public void Close() {
if (hComm!=INVALID_HANDLE_VALUE) {
CloseHandle(hComm);
}
}
public byte[] Read(int NumBytes) {
byte[] BufBytes;
byte[] OutBytes;
BufBytes = new byte[NumBytes];
if (hComm!=INVALID_HANDLE_VALUE) {
OVERLAPPED ovlCommPort = new OVERLAPPED();
int BytesRead=0;
ReadFile(hComm,BufBytes,NumBytes,ref BytesRead,ref ovlCommPort);
OutBytes = new byte[BytesRead];
Array.Copy(BufBytes,OutBytes,BytesRead);
}
else {
throw(new ApplicationException("串口未打开！"));
}
return OutBytes;
}
public void Write(byte[] WriteBytes) {
if (hComm!=INVALID_HANDLE_VALUE) {
OVERLAPPED ovlCommPort = new OVERLAPPED();
int BytesWritten = 0;
WriteFile(hComm,WriteBytes,WriteBytes.Length,ref BytesWritten,ref ovlCommPort);
}
else {
throw(new ApplicationException("串口未打开！"));
}
}
}
`
用createfile 打开串口时，当串口号小于10时，打开正常。
当串口号大于9时则打开失败，GetLastError 返回值为2，错误提示为 系统找不到指定的文件。
原因是设备名不对。当串口小10时设备名为COMx, 当串口时大于9时为\\.\COMx
浙公网安备 33010602011771号