iMX6 NFS启动
1、Tftp下载uImage：
1.1，设置ubuntu
(1) Setup tftp server files
# apt-get install tftpd tftp openbsd-inetd
(2) make a tftp directory Here we make /opt/tftpboot be a tftp directory.
# mkdir /opt/tftpboot
# chmod 777 /opt/tftpboot
(3) Open /etc/inetd.conf and edit it
# gedit /etc/inetd.conf
Add this line:
tftp dgram udp wait nobody /usr/sbin/tcpd /usr/sbin/in.tftpd /opt/tftpboot
(4)Restarting tftp service
#sudo /etc/init.d/openbsd-inetd restart
可以根据你的uImage文件放在路径，修改上述路径；也可以在/opt/tftpboot目录下生成一个目标连接文件。
1.2，tftp下载uImage
MX6Q SABRESD U-Boot >tftpboot uImage
2、文件系统以NFS方式加载
2.1 ，设置ubuntu
(1)， Install NFS server package
# apt-get install nfs-kernel-server
(2)， Configure portmap
# dpkg-reconfigure portmap
Select “NO”
(3) ，Configure mounted directory and authority
# gedit /etc/exports
Add the following line at the end of the
file:
/home/ rootfs *(rw,sync,no_root_squash)
(4) ，Restart the NFS service
#sudo /etc/init.d/portmap restart
#sudo /etc/init.d/nfs-kernel-server restart
2.2，通过串口设置uboot变量设置
setenv ipaddr 192.168.1.xxx #设置板子IP
setenv serverip 192.168.1.xxx #设置为开发机的IP
setenv bootfile uImage
setenv nfsroot /home/rootfs
setenv bootargs_base 'setenv bootargs console=ttymxc0,115200'
setenv bootargs_nfs 'setenv bootargs ${bootargs} root=/dev/nfs ip=dhcp nfsrootdebug nfsroot=${serverip}:${nfsroot},v3,tcp fec_mac=${ethaddr} video=mxcfb0:dev=ldb,CVBS-TV,if=RGB666,bpp=16'
setenv bootcmd_net 'run bootargs_base bootargs_nfs;bootm'
setenv bootcmd 'tftpboot uImage; run bootcmd_net'
saveenv
重启板子即可。
启动log：
U-Boot 2009.08-dirty (Jan 10 2014 - 16:58:26)
CPU: Freescale i.MX6 family TO1.2 at 792 MHz
Thermal sensor with ratio = 177
Temperature: 51 C, calibration data 0x5624ce69
mx6q pll1: 792MHz
mx6q pll2: 528MHz
mx6q pll3: 480MHz
mx6q pll8: 50MHz
ipg clock : 66000000Hz
ipg per clock : 66000000Hz
uart clock : 80000000Hz
cspi clock : 60000000Hz
ahb clock : 132000000Hz
axi clock : 264000000Hz
emi_slow clock: 132000000Hz
ddr clock : 528000000Hz
usdhc1 clock : 198000000Hz
usdhc2 clock : 198000000Hz
usdhc3 clock : 198000000Hz
usdhc4 clock : 198000000Hz
nfc clock : 24000000Hz
Board: i.MX6Q-SABRESD: unknown-board Board: 0x63012 [POR ]
Boot Device: MMC
I2C: ready
DRAM: 1 GB
hello,I am runing ok!
MMC: FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2,FSL_USDHC: 3
In: serial
Out: serial
Err: serial
Net: got MAC address from IIM: 00:00:00:00:00:00
FEC0 [PRIME]
detect 13088[2.7]
m13088_check_sum
err=0
Hit any key to stop autoboot: 0
PHY indentify @ 0x1 = 0x004dd072
FEC: Link is Up 796d
Using FEC0 device
TFTP from server 138.88.8.192; our IP address is 138.88.8.122
Filename 'uImage'.
Load address: 0x10800000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################
done
Bytes transferred = 4158452 (3f73f4 hex)
## Booting kernel from Legacy Image at 10800000 ...
Image Name: Linux-3.0.35-2666-gbdde708-g181b
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4158388 Bytes = 4 MB
Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.35-2666-gbdde708-g181bd49-dirty (bfg@tianfeng-Honmax-Server) 4
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX 6Quad/DualLite/Solo Sabre-SD Board
Ignoring unrecognised tag 0x54410008
Memory policy: ECC disabled, Data cache writealloc
CPU identified as i.MX6Q, silicon rev 1.2
PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 194560
Kernel command line: console=ttymxc0,115200 root=/dev/nfs ip=dhcp nfsrootdebug 6
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 512MB 256MB = 768MB total
Memory: 765124k/765124k available, 283452k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.init : 0x80008000 - 0x80087000 ( 508 kB)
.text : 0x80087000 - 0x80b3dd54 (10972 kB)
.data : 0x80b3e000 - 0x80ba1f80 ( 400 kB)
.bss : 0x80ba1fa4 - 0x80bf1f0c ( 320 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:624
MXC GPIO hardware
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
arm_max_freq=1GHz
MXC_Early serial console at MMIO 0x2020000 (options '115200')
bootconsole [ttymxc0] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3162.11 BogoMIPS).
print_constraints: dummy:
NET: Registered protocol family 16
print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
mx6_sabresd_board_init
yzw==>init_usb...
yzw==>imx6q_add_device_buttons
===================flexcan1 init.
register device:gpio_switch_mixdev
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
hw-breakpoint: maximum watchpoint size is 4 bytes.
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
bio: create slab <bio-0> at 0
mxs-dma mxs-dma-apbh: initialized
print_constraints: vmmc: 3300 mV
vgaarb: loaded
SCSI subsystem initialized
spi_imx imx6q-ecspi.0: probed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Freescale USB OTG Driver loaded, $Revision: 1.55 $
yzw==>pca953x_probe
Undetect 0
yzw==>chip->chip_type = 1000
yzw==>chip=bfcdcd28
pca953x 0-0018: failed reading register
mc_pfuze 1-0008: recv failed!:-5,80
mc_pfuze: probe of 1-0008 failed with error -1
imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7)
mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed
mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a
MIPI CSI2 driver module loaded
******************** mcu_i2c_init
-----------mcu_i2c_probe
Advanced Linux Sound Architecture Driver Version 1.0.24.
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
honmax_max7310_init==============================
pca953x 0-0018: failed writing register
Switching to clocksource mxc_timer1
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
honmax hm13088 version: 2 7
honmax hm13088 mac1: 66:55:44:33:22:11
honmax hm13088 mac2: cc:bb:aa:99:88:77
get config = 0
i2c-core: driver [hm13088] using legacy suspend method
i2c-core: driver [hm13088] using legacy resume method
PMU: registered new PMU device of type 0
Static Power Management for Freescale i.MX6
wait mode is enabled for i.MX6
cpaddr = c0880000 suspend_iram_base=c0918000
PM driver module loaded
iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering.
PCIE: imx_pcie_pltfm_probe start link up.
IMX PCIe port: link up.
ljc----------debug: pci_find_next_bus
PCI: bus0: Fast back to back transfers disabled
ljc----------debug: pci_find_next_bus
ljc----------debug: pci_find_next_bus
liutest start fixup imx6dq pcie tw6869
pci 0000:01:00.0: Setting PCI class for tw6868 PCIe device
liutest END fixup imx6dq pcie tw6869
PCI: bus1: Fast back to back transfers disabled
pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff 64bit pref]
pci 0000:00:00.0: BAR 0: set to [mem 0x01000000-0x010fffff 64bit pref] (PCI add)
pci 0000:00:00.0: BAR 9: assigned [mem 0x01100000-0x011fffff pref]
pci 0000:00:00.0: BAR 6: assigned [mem 0x01200000-0x0120ffff pref]
pci 0000:01:00.0: BAR 0: assigned [mem 0x01100000-0x01100fff pref]
pci 0000:01:00.0: BAR 0: set to [mem 0x01100000-0x01100fff pref] (PCI address [)
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io disabled]
pci 0000:00:00.0: bridge window [mem disabled]
pci 0000:00:00.0: bridge window [mem 0x01100000-0x011fffff pref]
liutest PCI: r->start =0x1000000 r->end =0x10fffff
IMX usb wakeup probe
add wake up source irq 75
IMX usb wakeup probe
cpu regulator mode:ldo_enable
i.MXC CPU frequency driver
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 1494
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
mxc_mipi_dsi mxc_mipi_dsi: i.MX MIPI DSI driver probed
MIPI DSI driver module loaded
mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver ldb
_regulator_get: get() with no identifier
Console: switching to colour frame buffer device 80x29
mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb
mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver lcd
mxc_sdc_fb mxc_sdc_fb.3: register mxc display driver ldb
mxc_sdc_fb mxc_sdc_fb.3: ipu1-di0 already in use
mxc_sdc_fb: probe of mxc_sdc_fb.3 failed with error -16
ch7024: TV encoder present: id = 45
ch7024: irq = ffffffff
ch7024: probe ok
CH7024: change to PAL video
CH7024: setup finished.
i2c-core: driver [ch7024] using legacy suspend method
i2c-core: driver [ch7024] using legacy resume method
imx-sdma imx-sdma: loaded firmware 1.1
imx-sdma imx-sdma: initialized
Serial: IMX driver
imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX
console [ttymxc0] enabled, bootconsole disabled
console [ttymxc0] enabled, bootconsole disabled
imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
imx-uart.2: ttymxc2 at MMIO 0x21ec000 (irq = 60) is a IMX
imx-uart.3: ttymxc3 at MMIO 0x21f0000 (irq = 61) is a IMX
imx-uart.4: ttymxc4 at MMIO 0x21f4000 (irq = 62) is a IMX
loop: module loaded
No sata disk.
m25p80 spi0.0: found m25p05-nonjedec, expected sst25vf016b
m25p80 spi0.0: m25p05-nonjedec (64 Kbytes)
Creating 2 MTD partitions on "m25p80":
0x000000000000-0x000000100000 : "bootloader"
mtd: partition "bootloader" extends beyond the end of device "m25p80" -- size t0
0x000000010000-0x000000010000 : "kernel"
mtd: partition "kernel" is out of reach -- disabled
GPMI NAND driver registered. (IMX)
vcan: Virtual CAN interface driver
CAN device driver interface
flexcan netdevice driver
flfec_enet_mii_bus: probed
PPP generic driver version 2.4.2
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
add wake up source irq 72
imx6q_sabresd_host1_vbus:1
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200
fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
ARC USBOTG Device Controller driver (1 August 2005)
mousedev: PS/2 mouse device common for all mice
yzw==>gpio_keys_probe
input: gpio-keys as /devices/platform/gpio-keys/input/input0
max11801_ts 1-0048: Failed to register interruptr [isl29023] using legacy susped
i2c-core: driver [isl29023] using legacy resume method
snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
TW6868_: v4l2 driver version 2.0.1 loaded
PCI register init called
liutest PCI: r->start =0x1100000 r->end =0x1100fff
PCI: enabling device 0000:01:00.0 (0140 -> 0142)
TW6869[0] TW68_devcount: 0
TW6869[0]: found at 0000:01:00.0, rev: 1, irq: 155, latency: 0, mmio: 0x1100000
TW6869[0]: Hi: 32bit PCI DMA supported
TW6869[0]: subsystem: 0000:0000, board: TW6869 [card=1,insmod option]
TW6869 hwinit1
usb 2-1: new high speed USB device number 2 using fsl-ehci
set tw68 VIDEO_CTRL2 2b :: 0xff00ff
DMA TW6869[0]: tw DMA_CONFIG 2b :: 0xff00ff
read tw68 VDELAY0 108 :: 0x14
read tw68 MISC_CONTROL2 196 :: 0xe7
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 4 ports detected
------set tv norm = PAL
------dev->crop setting set tv norm = PAL, width720 height576 size 829440
TW68_initdev TW6869[0]: request IRQ 155
Adding TW686v_devlist 80b8cddc
TW6869[0]: Overlay supported -1 .
*****1*****video DEVICE NAME : TW6869[0] video (TW686922) vfdev[1] 0xba1c9000
*****1*****video DEVICE NAME : TW6869[0] video (TW686922) minor 0 DMA 0 er
*****6*****video DEVICE NAME : TW6869[0] video (TW686922) minor 5 DMA 5 er
*****7*****video DEVICE NAME : TW6869[0] video (TW686922) vfdev[7] 0xba1c9e00
*****7*****video DEVICE NAME : T9[0] video (TW686922) minor 6 DMA 6 err0 0
*****8*****video DEVICE NAME : TW6869[0] video (TW686922) vfdev[8] 0xbad76000
*****8*****video DEVICE NAME : TW6869[0] video (TW686922) minor 7 DMA 7 er
vdev_init8 Video DEVICE NAME : TW6869[0] video (TW686922)
TW6869[0]: registered PCI device 1 [v4l2]:0 err: |9|
DBG sensor data is at 80bc3d18
==adv7180_io_init==
usb 2-1.2: new low speed USB device number 3 using fsl-ehci
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
mma8451 0-001c: read chip ID 0x1 is not equal to 0x1a or 0x2a!
mma8451: probe of 0-001c failed with error -22
imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1)
Bluetooth: Virtual HCI driver ver 1.3
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCIATH3K protocol initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci sdhci-esdhc-imx.2: no write-protect pin available!
mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA
mmc1: SDHCI controller on platform [sdhci-esdhc-imx.3] using DMA
mmc2: SDHCI controller on platform [sdhci-esdhc-imx.1] using DMA
mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed
VPU initialized
mxc_asrc registered
Galcore version 4.6.9.6622
Thermal calibration data is 0x5624ce69
Thermal sensor with ratio = 177
Anatop Thermal registered as thermal_zone0
anatop_thermal_probe: default cooling device is cpufreq!
input: USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2:1.0/1
generic-usb 0003:09DA:0260.0001: input,hidraw0: USB HID v1.10 Keyboard [ USB K0
input: USB Keyboard as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.2/2-1.2:1.1/2
generic-usb 0003:09DA:0260.0002: input,hidraw1: USB HID v1.10 Device [ USB Key1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
pca953x 0-0018: failed writing register
pca953x 0-0018: failed writing register
gps_ctrl_mixdev_init
gps_ctrl_mixdev_probe
gps_power_on:[1]
gps_power_on:1
gps_ctrl_mixdev_probe ok
gpio_switch_mixdev_init
gpio_switch_mixdev_probe
gpio_switch_mixdev_probe ok
usbcore: registered new interface driver snd-usb-audio
mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio
imx-hdmi-soc-dai imx-hdmi-soc-dai.0: Failed: Load HDMI-video first.
asoc: wm8960 <-> imx-ssi.1 mapping ok
Initialize HDMI-audio failed. Load HDMI-video first!
ALSA device list:
#0: wm8960-audio
NET: Registered protocol family 26
TCP cubic registered
NET: Registered protocol family 17
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
can: raw protocol (rev 20090105)
can: broadcast manager protocol (rev 20090105 t)
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
mmc1: new high speed DDR MMC card at address 0001
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
Bus freq driver module loaded
mmcblk0: mmc1:0001 MMC04G 3.54 GiB
mmcblk0boot0: mmc1:0001 MMC04G partition 1 2.00 MiB
Bus freq driver Enabled
mxc_dvfs_core_probe
mmcblk0boot1: mmc1:0001 MMC04G partition 2 2.00 MiB
DVFS driver module loaded
mmcblk0: p1
snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:01 UTC (1)
mmcblk0boot1: unknown partition table
eth0: Freescale FEC PHY driver [Generic PHY] (mii_bus:phy_addr=1:01, irq=-1)
mmcblk0boot0: unknown partition table
mmc2: new high speed SDIO card at address 0001
usb 2-1.1: new high speed USB device number 4 using fsl-ehci
option 2-1.1:1.0: GSM modem (1-port) converter detected
usb 2-1.1: GSM modem (1-port) converter now attached to ttyUSB0
option 2-1.1:1.1: GSM modem (1-port) converter detected
usb 2-1.1: GSM modem (1-port) converter now attached to ttyUSB1
option 2-1.1:1.2: GSM modem (1-port) converter detected
usb 2-1.1: GSM modem (1-port) converter now attached to ttyUSB2
PHY: 1:01 - Link is Up - 100/Full
Sending DHCP requests ., OK
IP-Config: Got DHCP answer from 0.0.0.0, my address is 138.88.8.151
IP-Config: Complete:
device=eth0, addr=138.88.8.151, mask=255.255.255.0, gw=138.88.8.1,
host=138.88.8.151, domain=, nis-domain=(none),
bootserver=0.0.0.0, rootserver=138.88.8.192, rootpath=, mtu=576
Root-NFS: nfsroot=/home/zhushangzhi/ltib/rootfs,v3,tcp
NFS: nfs mount opts='vers=2,udp,rsize=4096,wsize=4096,v3,tcp,nolock,addr=138.88'
NFS: parsing nfs mount option 'vers=2'
NFS: parsing nfs mount option 'udp'
NFS: parsing nfs mount option 'rsize=4096'
NFS: parsing nfs mount option 'wsize=4096'
NFS: parsing nfs mount option 'v3'
NFS: parsing nfs mount option 'tcp'
NFS: parsing nfs mount option 'nolock'
NFS: parsing nfs mount option 'addr=138.88.8.192'
NFS: MNTPATH: '/home/zhushangzhi/ltib/rootfs'
NFS: sending MNT request for 138.88.8.192:/home/zhushangzhi/ltib/rootfs
NFS: received 0 auth flavors
NFS: MNT request succeeded
VFS: Mounted root (nfs filesystem) on device 0:12.
Freeing init memory: 508K
starting pid 1482, tty '': '/etc/rc.d/rcS'
Mounting /proc and /sys
Starting the hotplug events dispatcher udevd
udevd (1491): /proc/1491/oom_adj is deprecated, please use /proc/1491/oom_score.
Synthesizing initial hotplug events
Setting the hostname to freescale
Mounting filesystems
mount: mounting usbfs on /proc/bus/usb failed: No such file or directory
starting pid 2687, tty '': '/etc/rc.d/rc_gpu.S'
enter: ch7024_fb_event
enter ch7024_fb_event val=9 ch7024_cur_mode=0
mount: mounting /dev/mmcblk1p1 on /sdcard failed: No such file or directory
starting pid 2698, tty '': '/etc/rc.d/rc_mxc.S'
can't mount SDCARD
update system failed
arm-none-linux-gnueabi-gcc (Freescale MAD -- Linaro 2011.07 -- Built at 2011/08)
root filesystem built on Sat, 02 Nov 2013 16:22:00 +0800
Freescale Semiconductor, Inc.
freescale login: -----------------rootfs boot OK
