spi 主机控制器驱动(spi_master)
spi_master
/* linux/drivers/spi/spi_s3c24xx.c
*
* Copyright (c) 2006 Ben Dooks
* Copyright (c) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/io.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
#include <plat/regs-spi.h>
#include <mach/spi.h>
/**
* s3c24xx_spi_devstate - per device data
* @hz: Last frequency calculated for @sppre field.
* @mode: Last mode setting for the @spcon field.
* @spcon: Value to write to the SPCON register.
* @sppre: Value to write to the SPPRE register.
*/
struct s3c24xx_spi_devstate {
unsigned int hz;
unsigned int mode;
u8 spcon;
u8 sppre;
};
struct s3c24xx_spi {
/* bitbang has to be first */
struct spi_bitbang bitbang;
struct completion done;
void __iomem *regs;
int irq;
int len;
int count;
void (*set_cs)(struct s3c2410_spi_info *spi,
int cs, int pol);
/* data buffers */
const unsigned char *tx;
unsigned char *rx;
struct clk *clk;
struct resource *ioarea;
struct spi_master *master;
struct spi_device *curdev;
struct device *dev;
struct s3c2410_spi_info *pdata;
};
#define SPCON_DEFAULT (S3C2410_SPCON_MSTR | S3C2410_SPCON_SMOD_INT)
#define SPPIN_DEFAULT (S3C2410_SPPIN_KEEP)
static inline struct s3c24xx_spi *to_hw(struct spi_device *sdev)
{
return spi_master_get_devdata(sdev->master);
}
static void s3c24xx_spi_gpiocs(struct s3c2410_spi_info *spi, int cs, int pol)
{
gpio_set_value(spi->pin_cs, pol);
}
static void s3c24xx_spi_chipsel(struct spi_device *spi, int value)
{
struct s3c24xx_spi_devstate *cs = spi->controller_state;
struct s3c24xx_spi *hw = to_hw(spi);
unsigned int cspol = spi->mode & SPI_CS_HIGH ? 1 : 0;
/* change the chipselect state and the state of the spi engine clock */
switch (value) {
case BITBANG_CS_INACTIVE:
hw->set_cs(hw->pdata, spi->chip_select, cspol^1);
writeb(cs->spcon, hw->regs + S3C2410_SPCON);
break;
case BITBANG_CS_ACTIVE:
writeb(cs->spcon | S3C2410_SPCON_ENSCK,
hw->regs + S3C2410_SPCON);
hw->set_cs(hw->pdata, spi->chip_select, cspol);
break;
}
}
static int s3c24xx_spi_update_state(struct spi_device *spi,
struct spi_transfer *t)
{
struct s3c24xx_spi *hw = to_hw(spi);
struct s3c24xx_spi_devstate *cs = spi->controller_state;
unsigned int bpw;
unsigned int hz;
unsigned int div;
unsigned long clk;
bpw = t ? t->bits_per_word : spi->bits_per_word;
hz = t ? t->speed_hz : spi->max_speed_hz;
if (!bpw)
bpw = 8;
if (!hz)
hz = spi->max_speed_hz;
if (bpw != 8) {
dev_err(&spi->dev, "invalid bits-per-word (%d)\n", bpw);
return -EINVAL;
}
if (spi->mode != cs->mode) {
u8 spcon = SPCON_DEFAULT;
if (spi->mode & SPI_CPHA)
spcon |= S3C2410_SPCON_CPHA_FMTB;
if (spi->mode & SPI_CPOL)
spcon |= S3C2410_SPCON_CPOL_HIGH;
cs->mode = spi->mode;
cs->spcon = spcon;
}
if (cs->hz != hz) {
clk = clk_get_rate(hw->clk);
div = DIV_ROUND_UP(clk, hz * 2) - 1;
if (div > 255)
div = 255;
dev_dbg(&spi->dev, "pre-scaler=%d (wanted %d, got %ld)\n",
div, hz, clk / (2 * (div + 1)));
cs->hz = hz;
cs->sppre = div;
}
return 0;
}
static int s3c24xx_spi_setupxfer(struct spi_device *spi,
struct spi_transfer *t)
{
struct s3c24xx_spi_devstate *cs = spi->controller_state;
struct s3c24xx_spi *hw = to_hw(spi);
int ret;
ret = s3c24xx_spi_update_state(spi, t);
if (!ret)
writeb(cs->sppre, hw->regs + S3C2410_SPPRE);
return ret;
}
static int s3c24xx_spi_setup(struct spi_device *spi)
{
struct s3c24xx_spi_devstate *cs = spi->controller_state;
struct s3c24xx_spi *hw = to_hw(spi);
int ret;
/* allocate settings on the first call */
if (!cs) {
cs = kzalloc(sizeof(struct s3c24xx_spi_devstate), GFP_KERNEL);
if (!cs) {
dev_err(&spi->dev, "no memory for controller state\n");
return -ENOMEM;
}
cs->spcon = SPCON_DEFAULT;
cs->hz = -1;
spi->controller_state = cs;
}
/* initialise the state from the device */
ret = s3c24xx_spi_update_state(spi, NULL);
if (ret)
return ret;
spin_lock(&hw->bitbang.lock);
if (!hw->bitbang.busy) {
hw->bitbang.chipselect(spi, BITBANG_CS_INACTIVE);
/* need to ndelay for 0.5 clocktick ? */
}
spin_unlock(&hw->bitbang.lock);
return 0;
}
static void s3c24xx_spi_cleanup(struct spi_device *spi)
{
kfree(spi->controller_state);
}
static inline unsigned int hw_txbyte(struct s3c24xx_spi *hw, int count)
{
return hw->tx ? hw->tx[count] : 0;
}
static int s3c24xx_spi_txrx(struct spi_device *spi, struct spi_transfer *t)
{
struct s3c24xx_spi *hw = to_hw(spi);
dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
t->tx_buf, t->rx_buf, t->len);
hw->tx = t->tx_buf;
hw->rx = t->rx_buf;
hw->len = t->len;
hw->count = 0;
init_completion(&hw->done);
/* send the first byte */
writeb(hw_txbyte(hw, 0), hw->regs + S3C2410_SPTDAT);
wait_for_completion(&hw->done);
return hw->count;
}
static irqreturn_t s3c24xx_spi_irq(int irq, void *dev)
{
struct s3c24xx_spi *hw = dev;
unsigned int spsta = readb(hw->regs + S3C2410_SPSTA);
unsigned int count = hw->count;
if (spsta & S3C2410_SPSTA_DCOL) {
dev_dbg(hw->dev, "data-collision\n");
complete(&hw->done);
goto irq_done;
}
if (!(spsta & S3C2410_SPSTA_READY)) {
dev_dbg(hw->dev, "spi not ready for tx?\n");
complete(&hw->done);
goto irq_done;
}
hw->count++;
if (hw->rx)
hw->rx[count] = readb(hw->regs + S3C2410_SPRDAT);
count++;
if (count < hw->len)
writeb(hw_txbyte(hw, count), hw->regs + S3C2410_SPTDAT);
else
complete(&hw->done);
irq_done:
return IRQ_HANDLED;
}
static void s3c24xx_spi_initialsetup(struct s3c24xx_spi *hw)
{
/* for the moment, permanently enable the clock */
clk_enable(hw->clk);
/* program defaults into the registers */
writeb(0xff, hw->regs + S3C2410_SPPRE);
writeb(SPPIN_DEFAULT, hw->regs + S3C2410_SPPIN);
writeb(SPCON_DEFAULT, hw->regs + S3C2410_SPCON);
if (hw->pdata) {
if (hw->set_cs == s3c24xx_spi_gpiocs)
gpio_direction_output(hw->pdata->pin_cs, 1);
if (hw->pdata->gpio_setup)
hw->pdata->gpio_setup(hw->pdata, 1);
}
}
static int __init s3c24xx_spi_probe(struct platform_device *pdev)
{
struct s3c2410_spi_info *pdata;
struct s3c24xx_spi *hw;
struct spi_master *master;
struct resource *res;
int err = 0;
master = spi_alloc_master(&pdev->dev, sizeof(struct s3c24xx_spi));
if (master == NULL) {
dev_err(&pdev->dev, "No memory for spi_master\n");
err = -ENOMEM;
goto err_nomem;
}
hw = spi_master_get_devdata(master);
memset(hw, 0, sizeof(struct s3c24xx_spi));
hw->master = spi_master_get(master);
hw->pdata = pdata = pdev->dev.platform_data;
hw->dev = &pdev->dev;
if (pdata == NULL) {
dev_err(&pdev->dev, "No platform data supplied\n");
err = -ENOENT;
goto err_no_pdata;
}
platform_set_drvdata(pdev, hw);
init_completion(&hw->done);
/* setup the master state. */
/* the spi->mode bits understood by this driver: */
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
master->num_chipselect = hw->pdata->num_cs;
master->bus_num = pdata->bus_num;
/* setup the state for the bitbang driver */
hw->bitbang.master = hw->master;
hw->bitbang.setup_transfer = s3c24xx_spi_setupxfer;
hw->bitbang.chipselect = s3c24xx_spi_chipsel;
hw->bitbang.txrx_bufs = s3c24xx_spi_txrx;
hw->master->setup = s3c24xx_spi_setup;
hw->master->cleanup = s3c24xx_spi_cleanup;
dev_dbg(hw->dev, "bitbang at %p\n", &hw->bitbang);
/* find and map our resources */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (res == NULL) {
dev_err(&pdev->dev, "Cannot get IORESOURCE_MEM\n");
err = -ENOENT;
goto err_no_iores;
}
hw->ioarea = request_mem_region(res->start, resource_size(res),
pdev->name);
if (hw->ioarea == NULL) {
dev_err(&pdev->dev, "Cannot reserve region\n");
err = -ENXIO;
goto err_no_iores;
}
hw->regs = ioremap(res->start, resource_size(res));
if (hw->regs == NULL) {
dev_err(&pdev->dev, "Cannot map IO\n");
err = -ENXIO;
goto err_no_iomap;
}
hw->irq = platform_get_irq(pdev, 0);
if (hw->irq < 0) {
dev_err(&pdev->dev, "No IRQ specified\n");
err = -ENOENT;
goto err_no_irq;
}
err = request_irq(hw->irq, s3c24xx_spi_irq, 0, pdev->name, hw);
if (err) {
dev_err(&pdev->dev, "Cannot claim IRQ\n");
goto err_no_irq;
}
hw->clk = clk_get(&pdev->dev, "spi");
if (IS_ERR(hw->clk)) {
dev_err(&pdev->dev, "No clock for device\n");
err = PTR_ERR(hw->clk);
goto err_no_clk;
}
/* setup any gpio we can */
if (!pdata->set_cs) {
if (pdata->pin_cs < 0) {
dev_err(&pdev->dev, "No chipselect pin\n");
goto err_register;
}
err = gpio_request(pdata->pin_cs, dev_name(&pdev->dev));
if (err) {
dev_err(&pdev->dev, "Failed to get gpio for cs\n");
goto err_register;
}
hw->set_cs = s3c24xx_spi_gpiocs;
gpio_direction_output(pdata->pin_cs, 1);
} else
hw->set_cs = pdata->set_cs;
s3c24xx_spi_initialsetup(hw);
/* register our spi controller */
err = spi_bitbang_start(&hw->bitbang);
if (err) {
dev_err(&pdev->dev, "Failed to register SPI master\n");
goto err_register;
}
return 0;
err_register:
if (hw->set_cs == s3c24xx_spi_gpiocs)
gpio_free(pdata->pin_cs);
clk_disable(hw->clk);
clk_put(hw->clk);
err_no_clk:
free_irq(hw->irq, hw);
err_no_irq:
iounmap(hw->regs);
err_no_iomap:
release_resource(hw->ioarea);
kfree(hw->ioarea);
err_no_iores:
err_no_pdata:
spi_master_put(hw->master);
err_nomem:
return err;
}
static int __exit s3c24xx_spi_remove(struct platform_device *dev)
{
struct s3c24xx_spi *hw = platform_get_drvdata(dev);
platform_set_drvdata(dev, NULL);
spi_unregister_master(hw->master);
clk_disable(hw->clk);
clk_put(hw->clk);
free_irq(hw->irq, hw);
iounmap(hw->regs);
if (hw->set_cs == s3c24xx_spi_gpiocs)
gpio_free(hw->pdata->pin_cs);
release_resource(hw->ioarea);
kfree(hw->ioarea);
spi_master_put(hw->master);
return 0;
}
#ifdef CONFIG_PM
static int s3c24xx_spi_suspend(struct device *dev)
{
struct s3c24xx_spi *hw = platform_get_drvdata(to_platform_device(dev));
if (hw->pdata && hw->pdata->gpio_setup)
hw->pdata->gpio_setup(hw->pdata, 0);
clk_disable(hw->clk);
return 0;
}
static int s3c24xx_spi_resume(struct device *dev)
{
struct s3c24xx_spi *hw = platform_get_drvdata(to_platform_device(dev));
s3c24xx_spi_initialsetup(hw);
return 0;
}
static struct dev_pm_ops s3c24xx_spi_pmops = {
.suspend = s3c24xx_spi_suspend,
.resume = s3c24xx_spi_resume,
};
#define S3C24XX_SPI_PMOPS &s3c24xx_spi_pmops
#else
#define S3C24XX_SPI_PMOPS NULL
#endif /* CONFIG_PM */
MODULE_ALIAS("platform:s3c2410-spi");
static struct platform_driver s3c24xx_spi_driver = {
.remove = __exit_p(s3c24xx_spi_remove),
.driver = {
.name = "s3c2410-spi",
.owner = THIS_MODULE,
.pm = S3C24XX_SPI_PMOPS,
},
};
static int __init s3c24xx_spi_init(void)
{
return platform_driver_probe(&s3c24xx_spi_driver, s3c24xx_spi_probe);
}
static void __exit s3c24xx_spi_exit(void)
{
platform_driver_unregister(&s3c24xx_spi_driver);
}
module_init(s3c24xx_spi_init);
module_exit(s3c24xx_spi_exit);
MODULE_DESCRIPTION("S3C24XX SPI Driver");
MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>");
MODULE_LICENSE("GPL");/*
* spi_bitbang.c - polling/bitbanging SPI master controller driver utilities
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/spinlock.h>
#include <linux/workqueue.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_bitbang.h>
/*----------------------------------------------------------------------*/
/*
* FIRST PART (OPTIONAL): word-at-a-time spi_transfer support.
* Use this for GPIO or shift-register level hardware APIs.
*
* spi_bitbang_cs is in spi_device->controller_state, which is unavailable
* to glue code. These bitbang setup() and cleanup() routines are always
* used, though maybe they're called from controller-aware code.
*
* chipselect() and friends may use use spi_device->controller_data and
* controller registers as appropriate.
*
*
* NOTE: SPI controller pins can often be used as GPIO pins instead,
* which means you could use a bitbang driver either to get hardware
* working quickly, or testing for differences that aren't speed related.
*/
struct spi_bitbang_cs {
unsigned nsecs; /* (clock cycle time)/2 */
u32 (*txrx_word)(struct spi_device *spi, unsigned nsecs,
u32 word, u8 bits);
unsigned (*txrx_bufs)(struct spi_device *,
u32 (*txrx_word)(
struct spi_device *spi,
unsigned nsecs,
u32 word, u8 bits),
unsigned, struct spi_transfer *);
};
static unsigned bitbang_txrx_8(
struct spi_device *spi,
u32 (*txrx_word)(struct spi_device *spi,
unsigned nsecs,
u32 word, u8 bits),
unsigned ns,
struct spi_transfer *t
) {
unsigned bits = spi->bits_per_word;
unsigned count = t->len;
const u8 *tx = t->tx_buf;
u8 *rx = t->rx_buf;
while (likely(count > 0)) {
u8 word = 0;
if (tx)
word = *tx++;
word = txrx_word(spi, ns, word, bits);
if (rx)
*rx++ = word;
count -= 1;
}
return t->len - count;
}
static unsigned bitbang_txrx_16(
struct spi_device *spi,
u32 (*txrx_word)(struct spi_device *spi,
unsigned nsecs,
u32 word, u8 bits),
unsigned ns,
struct spi_transfer *t
) {
unsigned bits = spi->bits_per_word;
unsigned count = t->len;
const u16 *tx = t->tx_buf;
u16 *rx = t->rx_buf;
while (likely(count > 1)) {
u16 word = 0;
if (tx)
word = *tx++;
word = txrx_word(spi, ns, word, bits);
if (rx)
*rx++ = word;
count -= 2;
}
return t->len - count;
}
static unsigned bitbang_txrx_32(
struct spi_device *spi,
u32 (*txrx_word)(struct spi_device *spi,
unsigned nsecs,
u32 word, u8 bits),
unsigned ns,
struct spi_transfer *t
) {
unsigned bits = spi->bits_per_word;
unsigned count = t->len;
const u32 *tx = t->tx_buf;
u32 *rx = t->rx_buf;
while (likely(count > 3)) {
u32 word = 0;
if (tx)
word = *tx++;
word = txrx_word(spi, ns, word, bits);
if (rx)
*rx++ = word;
count -= 4;
}
return t->len - count;
}
int spi_bitbang_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
{
struct spi_bitbang_cs *cs = spi->controller_state;
u8 bits_per_word;
u32 hz;
if (t) {
bits_per_word = t->bits_per_word;
hz = t->speed_hz;
} else {
bits_per_word = 0;
hz = 0;
}
/* spi_transfer level calls that work per-word */
if (!bits_per_word)
bits_per_word = spi->bits_per_word;
if (bits_per_word <= 8)
cs->txrx_bufs = bitbang_txrx_8;
else if (bits_per_word <= 16)
cs->txrx_bufs = bitbang_txrx_16;
else if (bits_per_word <= 32)
cs->txrx_bufs = bitbang_txrx_32;
else
return -EINVAL;
/* nsecs = (clock period)/2 */
if (!hz)
hz = spi->max_speed_hz;
if (hz) {
cs->nsecs = (1000000000/2) / hz;
if (cs->nsecs > (MAX_UDELAY_MS * 1000 * 1000))
return -EINVAL;
}
return 0;
}
EXPORT_SYMBOL_GPL(spi_bitbang_setup_transfer);
/**
* spi_bitbang_setup - default setup for per-word I/O loops
*/
int spi_bitbang_setup(struct spi_device *spi)
{
struct spi_bitbang_cs *cs = spi->controller_state;
struct spi_bitbang *bitbang;
int retval;
unsigned long flags;
bitbang = spi_master_get_devdata(spi->master);
if (!cs) {
cs = kzalloc(sizeof *cs, GFP_KERNEL);
if (!cs)
return -ENOMEM;
spi->controller_state = cs;
}
/* per-word shift register access, in hardware or bitbanging */
cs->txrx_word = bitbang->txrx_word[spi->mode & (SPI_CPOL|SPI_CPHA)];
if (!cs->txrx_word)
return -EINVAL;
retval = bitbang->setup_transfer(spi, NULL);
if (retval < 0)
return retval;
dev_dbg(&spi->dev, "%s, %u nsec/bit\n", __func__, 2 * cs->nsecs);
/* NOTE we _need_ to call chipselect() early, ideally with adapter
* setup, unless the hardware defaults cooperate to avoid confusion
* between normal (active low) and inverted chipselects.
*/
/* deselect chip (low or high) */
spin_lock_irqsave(&bitbang->lock, flags);
if (!bitbang->busy) {
bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
ndelay(cs->nsecs);
}
spin_unlock_irqrestore(&bitbang->lock, flags);
return 0;
}
EXPORT_SYMBOL_GPL(spi_bitbang_setup);
/**
* spi_bitbang_cleanup - default cleanup for per-word I/O loops
*/
void spi_bitbang_cleanup(struct spi_device *spi)
{
kfree(spi->controller_state);
}
EXPORT_SYMBOL_GPL(spi_bitbang_cleanup);
static int spi_bitbang_bufs(struct spi_device *spi, struct spi_transfer *t)
{
struct spi_bitbang_cs *cs = spi->controller_state;
unsigned nsecs = cs->nsecs;
return cs->txrx_bufs(spi, cs->txrx_word, nsecs, t);
}
/*----------------------------------------------------------------------*/
/*
* SECOND PART ... simple transfer queue runner.
*
* This costs a task context per controller, running the queue by
* performing each transfer in sequence. Smarter hardware can queue
* several DMA transfers at once, and process several controller queues
* in parallel; this driver doesn't match such hardware very well.
*
* Drivers can provide word-at-a-time i/o primitives, or provide
* transfer-at-a-time ones to leverage dma or fifo hardware.
*/
static void bitbang_work(struct work_struct *work)
{
struct spi_bitbang *bitbang =
container_of(work, struct spi_bitbang, work);
unsigned long flags;
int do_setup = -1;
int (*setup_transfer)(struct spi_device *,
struct spi_transfer *);
setup_transfer = bitbang->setup_transfer;
spin_lock_irqsave(&bitbang->lock, flags);
bitbang->busy = 1;
while (!list_empty(&bitbang->queue)) {
struct spi_message *m;
struct spi_device *spi;
unsigned nsecs;
struct spi_transfer *t = NULL;
unsigned tmp;
unsigned cs_change;
int status;
m = container_of(bitbang->queue.next, struct spi_message,
queue);
list_del_init(&m->queue);
spin_unlock_irqrestore(&bitbang->lock, flags);
/* FIXME this is made-up ... the correct value is known to
* word-at-a-time bitbang code, and presumably chipselect()
* should enforce these requirements too?
*/
nsecs = 100;
spi = m->spi;
tmp = 0;
cs_change = 1;
status = 0;
list_for_each_entry (t, &m->transfers, transfer_list) {
/* override speed or wordsize? */
if (t->speed_hz || t->bits_per_word)
do_setup = 1;
/* init (-1) or override (1) transfer params */
if (do_setup != 0) {
if (!setup_transfer) {
status = -ENOPROTOOPT;
break;
}
status = setup_transfer(spi, t);
if (status < 0)
break;
}
/* set up default clock polarity, and activate chip;
* this implicitly updates clock and spi modes as
* previously recorded for this device via setup().
* (and also deselects any other chip that might be
* selected ...)
*/
if (cs_change) {
bitbang->chipselect(spi, BITBANG_CS_ACTIVE);
ndelay(nsecs);
}
cs_change = t->cs_change;
if (!t->tx_buf && !t->rx_buf && t->len) {
status = -EINVAL;
break;
}
/* transfer data. the lower level code handles any
* new dma mappings it needs. our caller always gave
* us dma-safe buffers.
*/
if (t->len) {
/* REVISIT dma API still needs a designated
* DMA_ADDR_INVALID; ~0 might be better.
*/
if (!m->is_dma_mapped)
t->rx_dma = t->tx_dma = 0;
status = bitbang->txrx_bufs(spi, t);
}
if (status > 0)
m->actual_length += status;
if (status != t->len) {
/* always report some kind of error */
if (status >= 0)
status = -EREMOTEIO;
break;
}
status = 0;
/* protocol tweaks before next transfer */
if (t->delay_usecs)
udelay(t->delay_usecs);
if (!cs_change)
continue;
if (t->transfer_list.next == &m->transfers)
break;
/* sometimes a short mid-message deselect of the chip
* may be needed to terminate a mode or command
*/
ndelay(nsecs);
bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
ndelay(nsecs);
}
m->status = status;
m->complete(m->context);
/* restore speed and wordsize if it was overridden */
if (do_setup == 1)
setup_transfer(spi, NULL);
do_setup = 0;
/* normally deactivate chipselect ... unless no error and
* cs_change has hinted that the next message will probably
* be for this chip too.
*/
if (!(status == 0 && cs_change)) {
ndelay(nsecs);
bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
ndelay(nsecs);
}
spin_lock_irqsave(&bitbang->lock, flags);
}
bitbang->busy = 0;
spin_unlock_irqrestore(&bitbang->lock, flags);
}
/**
* spi_bitbang_transfer - default submit to transfer queue
*/
int spi_bitbang_transfer(struct spi_device *spi, struct spi_message *m)
{
struct spi_bitbang *bitbang;
unsigned long flags;
int status = 0;
m->actual_length = 0;
m->status = -EINPROGRESS;
bitbang = spi_master_get_devdata(spi->master);
spin_lock_irqsave(&bitbang->lock, flags);
if (!spi->max_speed_hz)
status = -ENETDOWN;
else {
list_add_tail(&m->queue, &bitbang->queue);
queue_work(bitbang->workqueue, &bitbang->work);
}
spin_unlock_irqrestore(&bitbang->lock, flags);
return status;
}
EXPORT_SYMBOL_GPL(spi_bitbang_transfer);
/*----------------------------------------------------------------------*/
/**
* spi_bitbang_start - start up a polled/bitbanging SPI master driver
* @bitbang: driver handle
*
* Caller should have zero-initialized all parts of the structure, and then
* provided callbacks for chip selection and I/O loops. If the master has
* a transfer method, its final step should call spi_bitbang_transfer; or,
* that's the default if the transfer routine is not initialized. It should
* also set up the bus number and number of chipselects.
*
* For i/o loops, provide callbacks either per-word (for bitbanging, or for
* hardware that basically exposes a shift register) or per-spi_transfer
* (which takes better advantage of hardware like fifos or DMA engines).
*
* Drivers using per-word I/O loops should use (or call) spi_bitbang_setup,
* spi_bitbang_cleanup and spi_bitbang_setup_transfer to handle those spi
* master methods. Those methods are the defaults if the bitbang->txrx_bufs
* routine isn't initialized.
*
* This routine registers the spi_master, which will process requests in a
* dedicated task, keeping IRQs unblocked most of the time. To stop
* processing those requests, call spi_bitbang_stop().
*/
int spi_bitbang_start(struct spi_bitbang *bitbang)
{
int status;
if (!bitbang->master || !bitbang->chipselect)
return -EINVAL;
INIT_WORK(&bitbang->work, bitbang_work);
spin_lock_init(&bitbang->lock);
INIT_LIST_HEAD(&bitbang->queue);
if (!bitbang->master->mode_bits)
bitbang->master->mode_bits = SPI_CPOL | SPI_CPHA | bitbang->flags;
if (!bitbang->master->transfer)
bitbang->master->transfer = spi_bitbang_transfer;
if (!bitbang->txrx_bufs) {
bitbang->use_dma = 0;
bitbang->txrx_bufs = spi_bitbang_bufs;
if (!bitbang->master->setup) {
if (!bitbang->setup_transfer)
bitbang->setup_transfer =
spi_bitbang_setup_transfer;
bitbang->master->setup = spi_bitbang_setup;
bitbang->master->cleanup = spi_bitbang_cleanup;
}
} else if (!bitbang->master->setup)
return -EINVAL;
/* this task is the only thing to touch the SPI bits */
bitbang->busy = 0;
bitbang->workqueue = create_singlethread_workqueue(
dev_name(bitbang->master->dev.parent));
if (bitbang->workqueue == NULL) {
status = -EBUSY;
goto err1;
}
/* driver may get busy before register() returns, especially
* if someone registered boardinfo for devices
*/
status = spi_register_master(bitbang->master);
if (status < 0)
goto err2;
return status;
err2:
destroy_workqueue(bitbang->workqueue);
err1:
return status;
}
EXPORT_SYMBOL_GPL(spi_bitbang_start);
/**
* spi_bitbang_stop - stops the task providing spi communication
*/
int spi_bitbang_stop(struct spi_bitbang *bitbang)
{
spi_unregister_master(bitbang->master);
WARN_ON(!list_empty(&bitbang->queue));
destroy_workqueue(bitbang->workqueue);
return 0;
}
EXPORT_SYMBOL_GPL(spi_bitbang_stop);
MODULE_LICENSE("GPL");
