(原創) 如何以2進位顯示8位數的七段顯示器? (SOC) (Verilog) (DE2)
Abstract
七段顯示器在DE2可當成Verilog的console，做為2進位的輸出結果。
Introduction
使用環境：Quartus II 7.2 SP3 + DE2(Cyclone II EP2C35F627C6)
簡單的使用switch當成二進位輸入，並用8位數的七段顯示器顯示2進位的結果。
Verilog / SWITCH_SEG7.v
1 /*
2 (C) OOMusou 2008 http://oomusou.cnblogs.com
3
4 Filename : SWITCH_SEG7.v
5 Compiler : Quartus II 7.2 SP3
6 Description : Demo how to use 2 bit 7 segment display
7 Release : 07/04/2008 1.0
8 */
9 module SWITCH_SEG7 (
10 //Host side
11 input CLOCK_50, // 50 MHz
12 input [3:0] KEY,
13 input [17:0] SW,
14 output [6:0] HEX0,
15 output [6:0] HEX1,
16 output [6:0] HEX2,
17 output [6:0] HEX3,
18 output [6:0] HEX4,
19 output [6:0] HEX5,
20 output [6:0] HEX6,
21 output [6:0] HEX7
22 );
23
24 SEG7_LUT_8 u0 (
25 .oSEG0(HEX0),
26 .oSEG1(HEX1),
27 .oSEG2(HEX2),
28 .oSEG3(HEX3),
29 .oSEG4(HEX4),
30 .oSEG5(HEX5),
31 .oSEG6(HEX6),
32 .oSEG7(HEX7),
33 .iDIG(SW),
34 .iWR(1'b1),
35 .iCLK(CLOCK_50),
36 .iRESET_n(KEY[0])
37 );
38
39 endmodule
2 (C) OOMusou 2008 http://oomusou.cnblogs.com
3
4 Filename : SWITCH_SEG7.v
5 Compiler : Quartus II 7.2 SP3
6 Description : Demo how to use 2 bit 7 segment display
7 Release : 07/04/2008 1.0
8 */
9 module SWITCH_SEG7 (
10 //Host side
11 input CLOCK_50, // 50 MHz
12 input [3:0] KEY,
13 input [17:0] SW,
14 output [6:0] HEX0,
15 output [6:0] HEX1,
16 output [6:0] HEX2,
17 output [6:0] HEX3,
18 output [6:0] HEX4,
19 output [6:0] HEX5,
20 output [6:0] HEX6,
21 output [6:0] HEX7
22 );
23
24 SEG7_LUT_8 u0 (
25 .oSEG0(HEX0),
26 .oSEG1(HEX1),
27 .oSEG2(HEX2),
28 .oSEG3(HEX3),
29 .oSEG4(HEX4),
30 .oSEG5(HEX5),
31 .oSEG6(HEX6),
32 .oSEG7(HEX7),
33 .iDIG(SW),
34 .iWR(1'b1),
35 .iCLK(CLOCK_50),
36 .iRESET_n(KEY[0])
37 );
38
39 endmodule
這是top module，主要將switch的值傳入iDIG，iWR是個enable，這裡沒特別用到，就傳1'b1即可。
Verilog / SWITCH_LUT.v
1 /*
2 (C) OOMusou 2008 http://oomusou.cnblogs.com
3
4 Filename : SWITCH_LUT.v
5 Compiler : Quartus II 7.2 SP3
6 Description : Demo how to use 8 bit 7 segment display
7 Release : 07/04/2008 1.0
8 */
9 module SEG7_LUT (
10 input [3:0] iDIG,
11 output reg [6:0] oSEG
12 );
13
14 always@(iDIG) begin
15 case(iDIG)
16 4'h1: oSEG = 7'b1111001; // ---t----
17 4'h2: oSEG = 7'b0100100; // | |
18 4'h3: oSEG = 7'b0110000; // lt rt
19 4'h4: oSEG = 7'b0011001; // | |
20 4'h5: oSEG = 7'b0010010; // ---m----
21 4'h6: oSEG = 7'b0000010; // | |
22 4'h7: oSEG = 7'b1111000; // lb rb
23 4'h8: oSEG = 7'b0000000; // | |
24 4'h9: oSEG = 7'b0011000; // ---b----
25 4'ha: oSEG = 7'b0001000;
26 4'hb: oSEG = 7'b0000011;
27 4'hc: oSEG = 7'b1000110;
28 4'hd: oSEG = 7'b0100001;
29 4'he: oSEG = 7'b0000110;
30 4'hf: oSEG = 7'b0001110;
31 4'h0: oSEG = 7'b1000000;
32 endcase
33 end
34
35 endmodule
2 (C) OOMusou 2008 http://oomusou.cnblogs.com
3
4 Filename : SWITCH_LUT.v
5 Compiler : Quartus II 7.2 SP3
6 Description : Demo how to use 8 bit 7 segment display
7 Release : 07/04/2008 1.0
8 */
9 module SEG7_LUT (
10 input [3:0] iDIG,
11 output reg [6:0] oSEG
12 );
13
14 always@(iDIG) begin
15 case(iDIG)
16 4'h1: oSEG = 7'b1111001; // ---t----
17 4'h2: oSEG = 7'b0100100; // | |
18 4'h3: oSEG = 7'b0110000; // lt rt
19 4'h4: oSEG = 7'b0011001; // | |
20 4'h5: oSEG = 7'b0010010; // ---m----
21 4'h6: oSEG = 7'b0000010; // | |
22 4'h7: oSEG = 7'b1111000; // lb rb
23 4'h8: oSEG = 7'b0000000; // | |
24 4'h9: oSEG = 7'b0011000; // ---b----
25 4'ha: oSEG = 7'b0001000;
26 4'hb: oSEG = 7'b0000011;
27 4'hc: oSEG = 7'b1000110;
28 4'hd: oSEG = 7'b0100001;
29 4'he: oSEG = 7'b0000110;
30 4'hf: oSEG = 7'b0001110;
31 4'h0: oSEG = 7'b1000000;
32 endcase
33 end
34
35 endmodule
這個一個七段顯示器的lookup table。
Verilog / SWITCH_LUT8.v
1 /*
2 (C) OOMusou 2008 http://oomusou.cnblogs.com
3
4 Filename : SWITCH_LUT8.v
5 Compiler : Quartus II 7.2 SP3
6 Description : Demo how to use 2 bit 7 segment display
7 Release : 07/04/2008 1.0
8 */
9 module SEG7_LUT_8 (
10 output [6:0] oSEG0,
11 output [6:0] oSEG1,
12 output [6:0] oSEG2,
13 output [6:0] oSEG3,
14 output [6:0] oSEG4,
15 output [6:0] oSEG5,
16 output [6:0] oSEG6,
17 output [6:0] oSEG7,
18 input [31:0] iDIG,
19 input iWR,
20 input iCLK,
21 input iRESET_n
22 );
23
24 reg [31:0] dig;
25
26 always@(posedge iCLK or negedge iRESET_n) begin
27 if (!iRESET_n)
28 dig <= 0;
29 else begin
30 if (iWR)
31 dig <= iDIG;
32 end
33 end
34
35 SEG7_LUT u0 (
36 .iDIG(dig[0:0]),
37 .oSEG(oSEG0),
38 );
39
40 SEG7_LUT u1 (
41 .iDIG(dig[1:1]),
42 .oSEG(oSEG1)
43 );
44
45 SEG7_LUT u2 (
46 .iDIG(dig[2:2]),
47 .oSEG(oSEG2)
48 );
49
50 SEG7_LUT u3 (
51 .iDIG(dig[3:3]),
52 .oSEG(oSEG3)
53 );
54
55 SEG7_LUT u4 (
56 .iDIG(dig[4:4]),
57 .oSEG(oSEG4)
58 );
59
60 SEG7_LUT u5 (
61 .iDIG(dig[5:5]),
62 .oSEG(oSEG5)
63 );
64
65 SEG7_LUT u6 (
66 .iDIG(dig[6:6]),
67 .oSEG(oSEG6)
68 );
69
70 SEG7_LUT u7 (
71 .iDIG(dig[7:7]),
72 .oSEG(oSEG7)
73 );
74
75 endmodule
2 (C) OOMusou 2008 http://oomusou.cnblogs.com
3
4 Filename : SWITCH_LUT8.v
5 Compiler : Quartus II 7.2 SP3
6 Description : Demo how to use 2 bit 7 segment display
7 Release : 07/04/2008 1.0
8 */
9 module SEG7_LUT_8 (
10 output [6:0] oSEG0,
11 output [6:0] oSEG1,
12 output [6:0] oSEG2,
13 output [6:0] oSEG3,
14 output [6:0] oSEG4,
15 output [6:0] oSEG5,
16 output [6:0] oSEG6,
17 output [6:0] oSEG7,
18 input [31:0] iDIG,
19 input iWR,
20 input iCLK,
21 input iRESET_n
22 );
23
24 reg [31:0] dig;
25
26 always@(posedge iCLK or negedge iRESET_n) begin
27 if (!iRESET_n)
28 dig <= 0;
29 else begin
30 if (iWR)
31 dig <= iDIG;
32 end
33 end
34
35 SEG7_LUT u0 (
36 .iDIG(dig[0:0]),
37 .oSEG(oSEG0),
38 );
39
40 SEG7_LUT u1 (
41 .iDIG(dig[1:1]),
42 .oSEG(oSEG1)
43 );
44
45 SEG7_LUT u2 (
46 .iDIG(dig[2:2]),
47 .oSEG(oSEG2)
48 );
49
50 SEG7_LUT u3 (
51 .iDIG(dig[3:3]),
52 .oSEG(oSEG3)
53 );
54
55 SEG7_LUT u4 (
56 .iDIG(dig[4:4]),
57 .oSEG(oSEG4)
58 );
59
60 SEG7_LUT u5 (
61 .iDIG(dig[5:5]),
62 .oSEG(oSEG5)
63 );
64
65 SEG7_LUT u6 (
66 .iDIG(dig[6:6]),
67 .oSEG(oSEG6)
68 );
69
70 SEG7_LUT u7 (
71 .iDIG(dig[7:7]),
72 .oSEG(oSEG7)
73 );
74
75 endmodule
35行
1 SEG7_LUT u0 (
2 .iDIG(dig[0:0]),
3 .oSEG(oSEG0),
4 );
2 .iDIG(dig[0:0]),
3 .oSEG(oSEG0),
4 );
不同於(原創) 如何以16進位顯示8位數的七段顯示器? (SOC) (Verilog) (DE2)顯示的是16進位，所以要傳入dig[3:0]，現在只要顯示2進位，所以只傳入dig[0:0]即可，其餘同理。
完整程式碼下載
switch_seg7_hw_binary.7z
Conclusion
由於有讀者問起如何用七段顯示器顯示2進位，以(原創) 如何以16進位顯示8位數的七段顯示器? (SOC) (Verilog) (DE2)為藍本，做了小修改後，就可顯示2進位了。
